Index Paper Attachment; Changing The Media Size Of The Front Deck (Left/Right); Image/Operation Check In User Mode; Adjustment Of Image Left End Margin - Canon imageRUNNER 5065 series Service Manual

2.2.17 Index Paper Attachment

iR5065 / iR 5055 / iR5075 / / /
1) Determine the cassette for index paper from either of Cassette 3 or 4. Press
the release button of the cassette you determined to slide it toward the
front. Fit the 2 one-touch supports [1] onto the holes [2] of the cassette,
and press the pin into the hole to fix them in place.
2) Fit the holes of the index paper attachment [3] on the one-touch supports
[1].
3) Set the base sheet [4] on the cassette.
[1]
[2]
4) Close the cassette.
2.2.18 Changing the Media Size of the Front Deck (Left/
Right)
iR5065 / iR 5055 / iR5075 / / /
1) Hold down the release button to slide the deck out.
2) Remove the screw [4] of the trailing end plate [1], the left guide plate [2],
and the right guide plate [3] respectively, and secure each plate in place
at the position of the size that user wishes.
Default setting: A4 size
After setting the size, set the deck into the host machine.
[3]
[4]
3) Attach the new media size label onto the media size plate of the deck.
4) In case the size is changed, register the front deck media size in service
mode.
Right deck: COPIER > OPTION > CST > P-SZ-C1
Left deck: COPIER > OPTION > CST > P-SZ-C2
A4=6, B5=15, and LTR=18

2.2.19 Image/Operation Check in User Mode

iR5065 / iR 5055 / iR5075 / / /
1) Press [Reset] twice and return to the main screen. Using test sheet, check
the copy operation and copy image.
- Copy operation: Check to see that the copy operation is appropriate.
- Duplexing copy operation: Check to see that the paper feeding at the
duplexing unit is appropriate.
- Pickup operation: Check to see that paper pickup from each source of paper
is appropriate.
- Operation noise: Check to see that there is no abnormal sound.
- Fixed ratio reproduction: Check the image quality for each fixed ratio
reproduction.
- Multiple copies: Check to see that the copy operation for a specified
number of sheets is appropriate.
- Check to see that print images picked up from each cassette/deck are within
the scope of specifications.
Specification for image left end margin: 2.5 -/+1.5mm
Specification for image leading edge margin: 4.0-1.5/-1.0mm
[3]
[1]
[4]
F-2-51
[1]
[2]
[4]
F-2-52
In case the values is/are out of the scope of the specifications, see
'Adjustment of image left end margin' and 'Adjustment of image leading
0015-4673
edge margin'.
* In case there is a difference in density between the left and the right of the
image, adjust the height of the primary charging wire at the rear side to
correct it.
Due to the drop of toner from the drum separation claw, there may be a
dirty image in the initial 10 sheets. This dirt disappears as copy volume
goes on.
2) At customer's desire, set the standard mode from user mode or service
mode.
3) Place media in the right/left decks.
4) Close the right/left decks. Tear off the relevant media size label [1] from
the mount sheet, and then attach it onto the media size plate of the deck.
5) Hold down the release button, and then slide Cassette3 and 4 out.
6) Tear off the relevant media size label [1] from the mount sheet, and attach
it onto the media size plate [2] of the cassette. Set the media size plate in
0015-4674
the cassette.
7) Close each cassette.

2.2.20 Adjustment of Image Left End Margin

iR5065 / iR 5055 / iR5075 / / /
<Cassette 3/4>
1) Hold down the cassette release button, and then slide Cassette 3 and 4 out.
2) Loosen the 2 fixing screws [1] at the left/right of the cassette.
0015-4675
3) Adjust the position of the cassette body [1] by shifting it to the front or the
rear.
Shift to the rear = Decreases the left end margin
Shift to the front = Increases the left end margin
[1]
F-2-53
[1] [2]
F-2-54
[1]
F-2-55
Chapter 2
0015-4676
2-13