Page 3
Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.
Page 4
It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please go to www.enterasys.com/support/ or contact Enterasys Customer Support at 353 61 705586 (Ireland).
Page 5
SJ/T 11363-2006 standard. This table shows where these substances may be found in the supply chain of Enterasys electronic information products, as of the date of sale of the enclosed product. Note that some of the component types listed above may or may not be a part of the enclosed product.
Page 6
CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc., on behalf of itself and its Affiliates (as hereinafter defined) (“Enterasys”) that sets forth Your rights and obligations with respect to the Enterasys software program/firmware (including any accompanying documentation, hardware or media) (“Program”) in the package...
Page 7
Enterasys, and, accordingly, You hereby agree to maintain complete books, records and accounts showing (i) license fees due and paid, and (ii) the use, copying and deployment of the Program. You also grant to Enterasys and its authorized...
Page 8
Agreement. 12. WAIVER. A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition. Enterasys’ failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion.
Mounting the Power Supply to a Wall ....................2-13 Mounting the Power Supply to a Pole ....................2-13 Connecting the DC Power Supply to the WS-AP3660 ................2-14 Connecting the Power Supply to AC Power ................... 2-16 Appendix A: Specifications Appendix B: Regulatory Information WS-AP3660 ..............................B-1...
Page 10
WS-AP3660 Bottom View........................1-3 Mounting Bracket and Spacer Orientation..................2-4 Completed Bracket Installation ......................2-4 Mounting the WS-AP3660 to a Wall ....................2-5 WS-AP3660 Pole Mount Options ....................... 2-6 Attaching Straps to the Mounting Bracket ..................2-7 Installing Terminator Caps........................2-8 RJ45 Cable Gland Adapter Assembly ....................
About This Guide The guide describes how to mount and connect cables to the Enterasys Wireless Outdoor Access Point WS-AP3660. In addition, this guide provides information on the product certifications and national approvals for the WS-AP3660. Note: This guide does not provide information on configuration of the Enterasys Wireless Outdoor APs.
The manuals listed below can be obtained from the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site: https://extranet.enterasys.com/downloads/ • Enterasys Wireless AP External Antenna Site Preparation and Installation Guide • Enterasys Wireless Convergence Software User Guide Typographical Conventions The following typographical conventions and icons are used in this document.
Getting Help Getting Help For additional support related to the WS-AP3660 or this document, contact Enterasys Networks using one of the following methods: World Wide Web www.enterasys.com/support/ Phone 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/support/...
AP3660 to walls, rails, and poles. The WS-AP3660 is an 802.11n AP that supports 802.11a/802.11g and 802.11b legacy devices. It is delivered in a rugged enclosure. The WS-AP3660 supports a variety of antennas, providing range and coverage versatility.
WS-AP3660 Overview Figure 1-1 WS-AP3660 Front View Note: The Enterasys Wireless Outdoor APs do not work without the Enterasys Wireless Controller. The following views (see Figure 1-2 Figure 1-3) illustrate the connections to the WS-AP3660. Figure 1-2 WS-AP3660 Top View...
Note: The WS-AP3660 provides six external antenna ports. The network administrator determines which antenna port will be used based on the external antenna selected. The WS-AP3660 can also be configured to select the antenna that provides the best possible data transmission (diversity).
Figure 1-3 on page 1-3). This port is used to connect a console device to the WS-AP3660 through a serial cable. The console device can be a PC or workstation running a VT-100 terminal adapter emulator, or a VT-100 terminal.
The WS-AP3660 includes an internal temperature sensor for monitoring the temperature of the PCB. If the WS-AP3660 temperature changes (either too low or too high), an alert is generated and written to the log file for the AP. The sensor monitors the AP internal temperature, and creates the alert when the temperature enters either zone.
Installation This chapter provides installation instructions for the Enterasys Wireless Outdoor Access Point WS-AP3660 and the optional WS-AP3660 Power Supply. For information about... Refer to page... Package Contents Separately Ordered Components WS-AP3660 Installation Procedures WS-AP3660 Power Supply Installation Procedures 2-11 Package Contents The WS-AP3660 package includes components necessary for installation.
Item Waterproof cable gland adapter assembly Enterasys Wireless Outdoor AP Quick Reference Perform a visual inspection of the WS-AP3660 for any signs of physical damage. Contact Enterasys Networks if there are any signs of damage. Refer to “Getting Help” on page xi for details.
PD-9001GR-ENT (this is an indoor PoE injector) • Terminator cap. This part is listed as a spare item as the WS-AP3660 is shipped with six terminator caps. If you are not attaching six antennas to the WS-AP3660, you must use a terminator cap on the antenna connector not being used.
Determine the desired orientation (vertical or horizontal) of the mounting bracket (see Figure 2-1 on page 2-4). Attach the mounting bracket and spacer to the WS-AP3660 using four M6 screws, four spring washers, and four flat washers (see Figure 2-2 on page 2-4).
Secure the WS-AP3660 to the wall with four screws (see Figure 2-3 on page 2-5). Note: Screws for attaching the WS-AP3660 to a wall are not supplied with the product. The type and length of the screws will depend on the wall type and thickness. Figure 2-3...
Installation WS-AP3660 Installation Procedures Mounting the WS-AP3660 to a Pole To fit the mounting plate to a pole: Determine the desired mounting orientation of the WS-AP3660 (see Figure 2-4). Figure 2-4 WS-AP3660 Pole Mount Options Vertical bracket on vertical pole...
Tighten the tensioning screw to adapt the strap to the diameter of the pole. Attaching Antennas Notes: The total number of required antennas and associated port locations on the WS-AP3660 is dependant on the coverage area and the type of antennas selected.
Terminator cap Antenna connector LAN/Console Connections (with Cable Gland Adapter Assembly) The WS-AP3660 has both a LAN and a Console port. Refer to Figure 1-3 on page 1-3 for the location of these ports. Before connecting an RJ45 cable (not provided) to either port, a waterproof...
Page 29
WS-AP3660 Installation Procedures Installation Slide the claw and seal onto the RJ45 cable. Screw the main body into the LAN or Console port of the WS-AP3660. Main body LAN or Console port Plug the RJ45 cable into the LAN or Console port.
Page 30
Installation WS-AP3660 Installation Procedures Slide the seal and claw into the main body. Secure the seal nut onto the main body. Tighten the assembly by hand. 2-10...
• Power over Ethernet (PoE) Power is provided to the LAN port of the WS-AP3660 with a PoE injector. The PoE injector must be 802.3at compliant and is not provided with the WS-AP3660. Note: The RJ45 connector used for providing PoE to the WS-AP3660 must be contained within a waterproof adapter assembly before being installed.
Installation WS-AP3660 Power Supply Installation Procedures Attaching the Mounting Bracket To attach the mounting bracket to the WS-AP3660 Power Supply: Determine the desired orientation (vertical or horizontal) of the mounting bracket (see Figure 2-9). In the horizontal position, two power supplies can be attached to one bracket.
Mounting the Power Supply to a Wall Mounting the Power Supply to a Pole To mount the power supply to a pole: Determine the desired mounting orientation of the power supply (see Figure 2-12 page 2-14). Enterasys Wireless Outdoor WS-AP3660 Installation Guide 2-13...
1-3 for the location of the DC connector). Screw on and hand tighten the knurled knob securely. Insert one end of the DC to DC cable into the DC connector on the bottom of the WS-AP3660 Power Supply (see Figure 2-13 on page 2-15).
AC Power Receptacle DC Connector Note: The DC to DC cable forms a drip loop that allows water to safely drip away from the connections to both the WS-AP3660 and Power Supply (see Figure 2-14 on page 2-15). Screw on and hand tighten the knurled knob securely.
WS-AP3660 Power Supply Installation Procedures Connecting the Power Supply to AC Power The WS-AP3660 Power Supply provides a power receptacle for connecting the unit to an external AC power source. The power supply is shipped with a waterproof AC connector assembly (see Figure 2-15), but a power cord is not provided.
Pin 1 - Hot Pin 3 - Neutral Pin 2 - Not used Pin 4 - Ground Secure the wires by tightening the single lock nut with a 1.5 mm (Hex) driver. Lock nut Enterasys Wireless Outdoor WS-AP3660 Installation Guide 2-17...
Page 38
10. Insert the plug into the AC power source. Electrical Hazard: The connection to the AC power source should be made by a properly trained and licensed electrician in accordance with local codes and regulations. This completes the installation of the WS-AP3660. 2-18...
Specifications This appendix lists the specifications for the Enterasys Wireless Outdoor Access Point WS-AP3660 and the WS-AP3660 Power Supply. Table A-1 Specifications for the WS-AP3660 Item Specification Enclosure material Metal enclosure IP67 rated Power source 802.3at compliant PoE PD 12V DC input Power consumption <...
Table A-2 Specifications for the WS-AP3660 Power Supply Item Specification Enclosure material Metal enclosure IP67 rated AC Input 90 to 264V DC output Outside dimensions (max) 8.5 x 4.8 inches 215 x 122 mm RoHS compliant Water/Dust Proof Ratings NEMA Type 4...
The following regulatory information applies to the WS-AP3660. WS-AP3660 External Antenna AP Approved external antennas The WS-AP3660 must only be used with certified external antennas. Any unused antenna ports must be terminated. For a list of approved external antennas, see “WS-AP3660 Approved External...
Warning: The WS-AP3660s must be installed and used in strict accordance with the manufacturer's instructions as described in this guide and related documentation for the device to which the WS-AP3660 is connected. Any other installation or use of the product violates FCC Part 15 regulations.
2.4 GHz and 5 GHz frequency ranges. This device must not be co-located or operated in conjunction with any other antenna or transmitter. The radiated output power of the WS-AP3660 is below the FCC radio frequency exposure limits as specified in “Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields” (OET Bulletin 65, Supplement C).
WS-AP3660 will use the proper frequencies and power outputs for that country code. The WS-AP3660 is intended for outdoor use and must be installed in a proper outdoor location. Contact local Authority for procedure to follow and regulatory information. For more details on legal combinations of frequencies, power levels and antennas, contact Enterasys.
Con la presente Enterasys dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Spanish Por medio de la presente Enterasys declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
WS-AP3660 Slovenian Šiuo Enterasys deklaruoja, kad šis Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Latvian Ar šo Enterasys deklarē, ka Radio LAN device atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem Lithuanian Enterasys deklaruoja, kad Radio LAN device atitinka 1999/5/EC Direktyvos esminius reikalavimus ir kitas nuostatas".
The WS-AP3660 must not be operated until properly configured for the customer’s geographic location. Caution: The user or installer is responsible to ensure that the WS-AP3660 is operated according to channel limitations, indoor / outdoor restrictions, license requirements, and within power level limits for the current country of operation.
WS-AP3660 European Spectrum Usage Rules The AP configured with approved internal or external antennas can be used for indoor and outdoor transmissions throughout the European community as displayed in Table B-1. Some restrictions apply in Belgium, France, Greece, and Italy.
Certifications of Other Countries WS-AP3660 Approved External Antennas The WS-AP3660 external antenna APs can be used with certified external antennas. However, in order to comply with the local laws and regulations, an approval may be required by the local regulatory authorities. The optional antennas listed in...