Table of Contents
Advertisement
Parameter
Value
FLAT, 20Hz,
25Hz, 31.5Hz,
40Hz, 50Hz,
63Hz, 80Hz,
Low Cut
100Hz, 125Hz,
160Hz, 200Hz,
250Hz, 315Hz,
400Hz, 500Hz,
630Hz, 800Hz
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
HighCut
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
Density
0–10
KIT: DELAY
Parameter
Value
DLY, PAN, TAPE
Type
ECHO
TempoSync
OFF, ON
Level
OFF, 1–255
DELAY
[LEVEL]
(TempoSync =
OFF) 0–255
(TempoSync =
ON) 1/32, 1/16T,
Time
1/32D, 1/16,
[TIME]
DELAY
1/8T, 1/16D, 1/8,
1/4T, 1/8D, 1/4,
1/2T, 1/4D, 1/2,
1/1T, 1/2D, 1/1
Feedback
0–255
DELAY
[FEEDBACK]
DLY, PAN
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
HighCut
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
0.0dB–-40.0dB
,
H Damp
(0.5 dB increments)
-INF
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
H DampF
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz
0.0dB–-40.0dB
,
L Damp
(0.5 dB increments)
-INF
Explanation
Specifies the frequency below which
the low-frequency region of the reverb
is cut.
Specifies the frequency above which
the high-frequency region of the
reverb is cut.
Adjusts the density of the reverb
sound.
Explanation
Selects the type of delay.
Choose ON if you want the delay time
to synchronize with the tempo.
Specifies the volume of the delay.
Specifies the time by which the sound
is delayed.
Adjusts the amount of feedback
(amount of repetition).
Specifies the frequency above which
the high-frequency region of the delay
sound is cut.
Adjusts the amount by which the
high-frequency region of the delay
sound is cut at each repetition.
Specifies the frequency above which H
Damp cuts the high-frequency region.
Adjusts the amount by which the low-
frequency region of the delay sound is
cut at each repetition.
Parameter
Value
80.0Hz, 100Hz,
125Hz, 160Hz,
200Hz, 250Hz,
L DampF
315Hz, 400Hz,
500Hz, 630Hz,
800Hz
PAN
Tap Time
0% –100%
TAP ECHO
S, M, L, S+M,
Mode
S+L, M+L,
S+M+L
-15dB–0dB–
Bass
+15dB
-15dB–0dB–
Treble
+15dB
L127–CENTER–
Pan S
R127
L127–CENTER–
Pan M
R127
L127–CENTER–
Pan L
R127
Tape Dist
0–8
W/F Rate
0–255
W/F Depth
0–255
KIT: MASTER FX
Parameter
Value
HPF, LPF,
LPF/HPF,
H BOOST,
L BOOST,
L/H BOOST,
ISOLATOR,
TRANSIENT,
TRANSIENT2,
Type
COMPRESSOR,
DRIVE,
OVERDRIVE,
DISTORTION,
FUZZ,
CRUSHER,
PHASER,
FLANGER, SBF,
NOISE
Editing a Kit's Settings (KIT Edit)
Explanation
Specifies the frequency below which L
Damp cuts the low-frequency region.
Adjusts the delay (tap) time of the
right side, relative to the left side as
100%.
Selects the combination of playback
heads.
S (Short), M (Middle), L (Long)
Adjusts the low-frequency region of
the echo sound.
Adjusts the high-frequency region of
the echo sound.
Specifies the panning of the S (Short)
playback head.
Specifies the panning of the M
(Middle) playback head.
Specifies the panning of the L (Long)
playback head.
Adjusts the amount of distortion for
the echo sound.
Adjusts the modulation speed of wow
and flutter.
Adjusts the depth of wow and flutter.
Explanation
Selects the type of MASTER FX.
HPF:
high pass filter
(cuts the low-frequency
region)
LPF:
low pass filter
(cuts the high-frequency
region)
LPF/HPF:
low pass filter / high pass
filter
(cuts the high-frequency or low-frequency
region)
H BOOST:
high boost
(boosts the high-
frequency region)
L BOOST:
low boost
(boosts the low-frequency
region)
L/H BOOST:
low boost / high boost
(boosts the low-frequency or high-frequency region)
ISOLATOR:
adjusts the balance of
the low, mid, and high-frequency
regions.
TRANSIENT:
strengthens or weakens
the attack and release.
TRANSIENT2:
uses the attack and
release to operate a filter.
COMPRESSOR:
compresses loud
input, making the maximum levels
more consistent.
DRIVE:
uncolored distortion.
OVERDRIVE:
overdrive
DISTORTION:
distortion
FUZZ:
fuzz
CRUSHER:
produces a lo-fi effect.
PHASER:
produces a phase effect.
FLANGER:
produces a flanging effect.
SBF:
side band filter
(a filter that passes only
.
specific frequency components)
NOISE:
adds noise.
23
Advertisement
Table of Contents
