Editing A Kit's Settings (Kit Edit); Kit; Kit: Reverb - Roland TR-8S Reference Manual

Editing a Kit's Settings
Selecting kits

(KIT)

Here's how to select kits.
1.
[KIT]
Press the button to make it light.
The KIT screen appears.
If the kit is being edited, an
number.
2.
[VALUE]
Use the knob to select a kit.
3.
Press the [KIT] button once again.
The [KIT] button goes dark, and you exit the KIT screen.
Copying a kit
(KIT COPY)
1.
[COPY]
Hold down the
button.
The KIT COPY screen appears.
2.
Use the [VALUE] knob to select the copy-source,
and press the [ENTER]
3.
Use the [VALUE] knob to select the copy-
destination, and press the
A confirmation message appears.
4.
To copy, use the [VALUE]knob to select
press the [ENTER]
If you decide to cancel, use the
[ENTER]
and then press the
Here's how to edit the settings of the currently selected kit.
* If you want to keep the edited kit settings, you must save the kit
(p. 29).
1.
[SHIFT]
Hold down the
button.
The KIT Edit screen appears.
2.
Select a parameter.
2-1.
Use the [VALUE]
2-2.
Press the [ENTER]
Proceed to editing the parameter value (step 3).
3.
Modify values.
3-1.
Use the [VALUE]
3-2.
[ENTER]
Press the
Return to selecting a parameter (step 2).
4.
[KIT]
Press the button.
Exit the KIT Edit screen.
22
"*"
is shown at the left side of the kit
button and press the
button.
[ENTER] button.
"OK,"
button.
[VALUE] knob to select
button.
button and press the
knob to select a parameter.
button.
knob to edit the parameter value.
button.
(KIT Edit)
Grouping instruments
You can create a group of multiple instruments and play their
layered sound with a single note.
You can use grouped master instruments in the following ways. The
slave instrument follows the master instrument.
5 Pattern input in
5 Pad performance in
5 Pad recording in
1.
Hold down the
button.
2.
Long-press the
specify as the master instrument.
The INST GROUP screen appears.
[KIT]
3.
While holding down the button that you pressed
in step 2, press the
to specify as the slave instrument.
The instruments that you selected as the master instrument and
the slave instrument are grouped.
MEMO
5 During TR-REC, when you press a grouped
[BD]–[RC]
the
and the [BD]–[RC]
5 During INST PLAY/INST REC, pressing a pad
grouped slave instrument does not produce sound.
and
5 If you press the
instrument's
instrument's
"Cancel,"
KIT
Parameter
[KIT]
Level

KIT: REVERB

Parameter
Type
Time
[KIT]+ REVERB
[LEVEL]
Level
[LEVEL]
REVERB
Pre Delay
"TR-REC"
"INST PLAY"
"INST REC"
[SHIFT] button and press the
[BD]–[RC] button that you want to
[BD]–[RC]
button that you want
button of the master instrument (
button of the slave instrument (
[MUTE] button, the same group's master
[BD]–[RC]
button lights and the slave
[BD]–[RC]
button blinks.
Value Explanation
-INF, -53.0dB–
Specifies the volume of the kit.
0.0dB–+10.0dB
Value Explanation
AMBI, ROOM,
HALL1, HALL2, Selects the type of reverb.
PLATE, MOD
0–255 Specifies the reverb time.
OFF, 1–255 Specifies the volume of the reverb.
Adjusts the time until the reverb
0ms–100ms
sound appears.
[KIT]
[BD]–[RC]
button,
) lights
) blinks.
[1]–[11]
of a