Adding Reverberation To The Sound (Reverb); Adding Delay To The Sound (Delay); Applying An Effect (Modulation Fx); Applying Tremolo (Tremolo) - Roland RD-2000 Owner's Manual

Adding Reverberation to the Sound (REVERB)

Applying reverb adds pleasing reverberation to what you play, so it
sounds almost as if you were playing in a concert hall.
1.
Press the ZONE EFFECTS [SELECT] button several times, to select
the "REVERB/DELAY."
2.
Turn the REVERB [TYPE] knob, to select the reverb type.
3.
Turn the REVERB [LEVEL], [TIME] and [PRE DELAY] knobs to
adjust the amount of reverb effect to be applied.
MEMO
5 If you use the ZONE EFFECTS [SELECT] button to select "CTRL, " the
[REV SEND] knob can adjust the reverb send level. If this value is
"0, " turning the REVERB [LEVEL]–[PRE DELAY] knobs has no effect.
& REV (Reverb Send Level) in the zone settings (ZONE EDIT)
5 If you hold down the [SHIFT] button and turn the REVERB
[LEVEL]–[PRE DELAY] knobs, the Reverb screen appears. In the
Reverb screen, you can edit the reverb type and other reverb-
related parameters.

Adding Delay to the Sound (DELAY)

By adding the delay effect, you can give the sound greater dimension,
with more fatness and breadth.
1.
Press the ZONE EFFECTS [SELECT] button several times, to select
the "REVERB/DELAY."
2.
Press the [DELAY ON] button to make the indicator light.
The delay effect will turn on/off each time you press the button.
3.
Turn the DELAY [TYPE] knob, to select the delay type.
4.
Turn the DELAY [LEVEL], [TIME] and [FEEDBACK] knobs to adjust
the character of the delay effect.
MEMO
If you use the ZONE EFFECTS [SELECT] button to select "CTRL, " the
[DLY SEND] knob can adjust the delay send level. If this value is "0, "
turning the DELAY [LEVEL]–[FEEDBACK] knobs has no effect.
& "DLY (Delay Send Level)" in the zone settings (ZONE EDIT)
16

Applying an Effect (MODULATION FX)

In the MODULATION FX section you can apply a variety of effects such
as modulation-type effects to zones 1–4.
MEMO
Effects cannot be applied to zones 5–8.
1.
Press the [ZONE EFFECTS] button to make the indicator light.
2.
In the MODULATION FX section, press the [ON] button to make
the indicator light.
The effect will turn on/off each time you press the button.
3.
In the MODULATION FX section, turn the [TYPE] knob to select
the effect type.
For a list of the effects that can be used in modulation FX, refer to
"Parameter Guide (English)" (PDF).
4.
In the MODULATION FX section, turn the [DEPTH], [RATE] and
[FEEDBACK] knobs to adjust the effect.
MEMO
For details on the effect parameters, refer to "Parameter Guide
(English)" (PDF). For details on how to obtain the PDF, refer to
"Obtaining PDF Manuals" on the front cover.
* You can assign this to a pedal by setting the Program Edit
"Pedal" parameter. In this case, if the SYSTEM setting "Control
Destination" is set to PROGRAM, you can control the tones
whose zone setting (ZONE EDIT) has a check mark for "MOD FX
(Modulation FX Control Destination). "

Applying Tremolo (TREMOLO)

In the TREMOLO section, you can adjust the rate and depth of the
tremolo effect.
MEMO
Tremolo is applied only to zones 1–4. It does not apply to zones 5–8.
1.
Press the [ZONE EFFECTS] button to make the indicator light.
2.
In the TREMOLO section, press the [ON] button to make the
indicator light.
The tremolo will turn on/off each time you press the button.
3.
In the TREMOLO section, turn the [TYPE] to select the tremolo
waveform.
4.
In the TREMOLO section, turn the [DEPTH] and [RATE] knobs to
adjust the tremolo.