Advertisement
To change the input type, remove the instrument from its housing. Grasp
the front bezel sides and pull forward to release it from the housing lock.
Locate the dip switch on the right pcb. Determine the input type desired
and change the dip switch setting as shown to the right.
NOTE :
NOTE :
NOTE : Factory default is set for thermocouple inputs.
NOTE :
NOTE :
After changing input selection with the DIP switches, be sure to change
the InP menu item (page 9) in the Secure Menu.
NOTE:
NOTE: InP menu item factory default is set for type "J" thermocouple,
NOTE:
NOTE:
NOTE:
Iron/Constantan
Scaling for thermocouple and RTD inputs is fixed for each range type.
See page 8 for scale ends.
Scaling for current and voltage inputs is field adjustable by using SCAL and SCAH in the Secure menu. Program
SCAL to the low end value of your transmitter. Program SCAH to the high end value of your transmitter. If the
span of your transmitter is less than 100 units (referred to as 'counts' in these instructions), multiply the
transmitter span by 10 and change the decimal point position in menu item dP.
For example, if you have a differential pressure transmitter with a range of -0.25 to +0.25 inches of water. SCAL
would be programmed to -250, SCAH to +250, and dP to 0.000.
VERIFY MODEL NUMBER ON THE INSTRUMENT TO DETERMINE OUTPUT TYPE
VERIFY MODEL NUMBER ON THE INSTRUMENT TO DETERMINE OUTPUT TYPE
VERIFY MODEL NUMBER ON THE INSTRUMENT TO DETERMINE OUTPUT TYPE
VERIFY MODEL NUMBER ON THE INSTRUMENT TO DETERMINE OUTPUT TYPE
VERIFY MODEL NUMBER ON THE INSTRUMENT TO DETERMINE OUTPUT TYPE
PRE-SET FROM FACTORY.
PRE-SET FROM FACTORY.
PRE-SET FROM FACTORY.
PRE-SET FROM FACTORY.
PRE-SET FROM FACTORY.
I n s t ruments with S S R
S S R
S S R
S S R o r MECHANICAL RELA
S S R
i n t h e f i e l d .
C A
C A
C A
C AUTION
C A
UTION
UTION
UTION
UTION: Dama
s t r i p .
s t r i p . Follo
s t r i p .
Follow the instructions carefull
Follo
Follo
s t r i p .
s t r i p .
Follo
1 . Remove the instrument from its housing. Grasp the front bezel sides and pull forward to release it
from the housing lock .
2 . Locate the desired logic jumper strip on the left printed circuit board. The OUTPUT A
is always located near the top edge.
INPUT SELECTION
INPUT SELECTION
INPUT SELECTION
INPUT SELECTION
INPUT SELECTION
OUTPUT
OUTPUT TYPE JUMPER SELECTION
OUTPUT
OUTPUT
OUTPUT
MECHANICAL RELAY Y Y Y Y type outputs can be changed to and from a 5 5 5 5 5 Vdc
MECHANICAL RELA
MECHANICAL RELA
MECHANICAL RELA
Dama
Dama
Damag g g g g e to the instrument ma
Dama
e to the instrument ma
e to the instrument ma
e to the instrument ma
e to the instrument may result fr
w the instructions carefull
w the instructions carefully y y y y . . . . .
w the instructions carefull
w the instructions carefull
TYPE JUMPER SELECTION
TYPE JUMPER SELECTION
TYPE JUMPER SELECTION
TYPE JUMPER SELECTION
y result from an incorrectl
y result fr
y result fr
y result fr
om an incorrectly installed jumper
om an incorrectl
om an incorrectl
om an incorrectl
3
DIP SWITCH LOCATION
THERMOCOUPLE INPUTS
RTD INPUTS
CURRENT INPUT
VOLTAGE INPUT
Vdc
Vdc output
Vdc
Vdc
y installed jumper
y installed jumper
y installed jumper
y installed jumper
OUTPUT A
OUTPUT A
OUTPUT A jumper stri p
OUTPUT A
1 2 3 4
Advertisement
