Menu 0 - Emerson 2202 Advanced User's Manual

Parameter
Introduction
x.00 description format
9

Menu 0

Table 9-1 Menu 0 parameters: single line descriptions
Par Description
01 Minimum set speed (Hz)
02 Maximum set speed (Hz)
03 Acceleration rate (s/100Hz)
04 Deceleration rate (s/100Hz)
05 Drive configuration
06 Motor rated current (A)
07 Motor rated speed (rpm)
08 Motor rated voltage (V)
09 Motor power factor (cos ϕ)
10 Parameter access
11 Start/Stop logic select
12 Brake controller enable
15 Jog reference (Hz)
16 Analog input 1 mode (mA)
17 Enable negative preset speeds
18 Preset speed 1 (Hz)
19 Preset speed 2 (Hz)
20 Preset speed 3 (Hz)
21 Preset speed 4 (Hz)
22 Load display units
23 Speed display units
24 Customer defined scaling
25 User security code
27 Power up keypad reference
28 Parameter copying
29 Load defaults
30 Ramp mode select
31 Stop mode select
32 Dynamic V to f select
33 Catch a spinning motor select
34 Terminal B7 mode select
35 Digital output control (terminal B3)
36 Analog output control (terminal B1)
37 Maximum switching frequency (kHz)
38 Autotune
39 Motor rated frequency (Hz)
40 Number of motor poles
41 Voltage mode select
42 Low frequency voltage boost (%)
43 Serial comms baud rate
44 Serial comms address
45 Software version
46 Brake release current threshold (%)
47 Brake apply current threshold (%)
48 Brake release frequency (Hz)
49 Brake apply frequency (Hz)
50 Pre-brake release delay (s)
51 Post brake release delay (s)
52 *Solutions Module dependant
53 *Solutions Module dependant
54 *Solutions Module dependant
55 Last trip
30
Parameter Keypad and
display communications
230/400/575/
www.controltechniques.com
Serial CT Modbus PLC Ladder
RTU programming
Default
Eur USA
0.0
50.0 60.0
5.0 33.0
10.0 33.0
AI.AV PAd
Drive rating
1500 1800
230/460/575/
690 690
0.85
L1
0 4
diS
1.5
4-.20
OFF (0)
0.0
0.0
0.0
0.0
Ld
Fr
1.000
0
0
no
no
1
1
OFF (0)
0
dig
n=0
Fr
3
0
50.0 60.0
Auto
Ur I Fd
3.0 1.0
19.2
1
50
10
1.0
2.0
1.0
1.0
CTSoft Menu 0
Corresponding extended
menu parameter
Pr 1.07
Pr 1.06
Pr 2.11
Pr 2.21
Pr 11.27
Pr 5.07
Pr 5.08
Pr 5.09
Pr 5.10
Pr 11.44
Pr 6.04
Pr 12.41
Pr 1.05
Pr 7.06
Pr 1.10
Pr 1.21
Pr 1.22
Pr 1.23
Pr 1.24
Pr 4.21
Pr 5.34
Pr 11.21
Pr 11.30
Pr 1.51
Pr 11.42
Pr 11.43
Pr 2.04
Pr 6.01
Pr 5.13
Pr 6.09
Pr 8.35
Pr 8.41
Pr 7.33
Pr 5.18
Pr 5.12
Pr 5.06
Pr 5.11
Pr 5.14
Pr 5.15
Pr 11.25
Pr 11.23
Pr 11.29
Pr 12.42
Pr 12.43
Pr 12.44
Pr 12.45
Pr 12.46
Pr 12.47
Pr 15.03
Pr 15.04
Pr 15.06
Pr 10.20
Commander SK Advanced User Guide
Advanced parameter
descriptions
Setting
Issue Number: 9