Emerson 2202 Advanced User's Manual page 27

Parameter
Introduction
x.00 description format
• The Custom list enables parameters to be added to a custom list made up of all available drive parameters. This enables the viewing of unrelated
parameters on the same screen. Custom files may be saved by the user for use at a later date.
• Many of the menus have associated block diagrams that graphically indicate how all of the related parameters interact. To change a parameter
value simply right-click on a parameter and select "Edit Parameter".
Table 8-1 Feature look up table
Feature
Acceleration rates
Allow negative
references
Analog I/O Menu 7
Analog output
Analog speed
reference 1
Analog speed
reference 2
Application menus Menu 18
At speed indicator bit
Auto reset
Autotune
Binary sum
Brake control 12.40 to 12.47
Braking
Catch a spinning motor
Copying
Coast to stop
Comms 11.23 to 11.26
Cost - per kWh
electricity
Current controller
Current feedback
Current limits
Current rating
DC bus voltage
DC injection braking
Deceleration rates
Defaults
Digital I/O Menu 8
Digital I/O read word
Digital I/O B3
Digital Input B4
Digital Input B5
Digital input B6
Digital input B7
Direction
Display units
Display timeout
Drive active
Drive ok
Dynamic V/F
Enable
External trip
Fan speed
Frequency input
Frequency output
Frequency reference
selection
Hard speed reference
High stability space
vector modulation
Commander SK Advanced User Guide
Issue Number: 9
Parameter Keypad and
display communications
2.10 2.11 to 2.19 2.30
1.10
7.19 7.20 7.33
1.36 7.01 7.06
1.37 7.02 7.11
Menu 20
3.06 10.05 10.06
10.34 10.35 10.36
5.12 5.17 5.23
9.29 9.30 9.31
10.11 10.10 10.30
6.09 5.12 5.17
11.42
6.01
6.42 6.43
6.16 6.17 6.24
4.13 4.14
4.01 4.02 4.17
4.07 4.18 4.15
11.32 4.24
5.05 2.08
6.01 6.06 6.07
2.20 2.21 to 2.29 2.31
11.43 11.46
8.20
8.01 8.11 8.21
8.02 8.12 8.22
8.03 8.13 8.23
8.04 8.14 8.24
8.05 8.15 8.25
1.12 10.13 10.14
4.21 5.34
11.41
1.11 10.02 10.40
10.01 10.36 10.40
5.13
6.15 6.29 8.02
10.32
6.45
3.32 3.33 3.34
3.17 3.18 8.21
1.14 1.15
3.22 3.23
5.19
www.controltechniques.com
Serial CT Modbus PLC Ladder
RTU programming
Parameter number (Pr)
2.32 2.33
7.08 7.09
7.12 7.13
10.07
10.01
5.24 5.10
9.32 9.33
10.31 6.01
6.25 6.26
4.04 4.20
4.16 4.19
2.35 2.36
8.31 8.41
6.04
6.04
6.04
8.35 Menu 3
6.30 6.31
8.12 8.22
3.43 3.44
CTSoft Menu 0
2.34 2.39
7.10 7.28 7.30
7.14 7.31 1.41
5.11
9.34
2.04 10.12 10.39
4.24 4.26 10.08
5.07 5.10 10.08
2.37 2.39
12.41 Menu 3
6.32 6.33 6.37
3.45 8.25
Advanced parameter
descriptions
10.40
10.09 10.17
10.09 10.17
10.40
27