Advertisement
Ô
Ô
NOTE
Connecting the Handset
Your local RadioShack store sells a variety of
longer coiled handset cords, which are
especially useful when you mount the phone
on a wall.
Using the Master/Secondary Setting
• If M is not set on at least one or more
phones, incoming calls might be
disconnected.
• If you connect only one system to a phone
line, set M/S to M.
• You can also connect other CID modules
that do not have the Call Waiting function to
the same phone line as your system, as long
as you do not connect more than four CID
modules total (including this phone).
• If you connect another type of CID module
that has Call Waiting (other than this system)
to the same phone line as your system, the
Call Waiting signal might be garbled or not
received.
Making a Call
If you dial a number over 15 digits, only the last
14 digits appear on the display.
Receiving a Call
• The NEW indicator remains flashing until
you have reviewed all new calls.
• The number of new calls does not change
until all calls have been reviewed and
NEW CALL
appears. The system new call
0
counter then resets to
.
Timer
If you lift the handset and don't dial a number,
the timer appears and starts to count up after
10 seconds.
2
2. Plug the other end of the cord into a
wall plate jack.
3. Align the base's keyhole slots with the
wall plate studs and slide the phone
downward to secure it.
4. To mount the phone directly on a wall
(after mounting the phone on a wall
plate), drill two holes 3
(83 mm) apart, one below the other.
5. Thread a screw into each hole, letting
the heads extend about 5mm from the
wall.
C
ONNECTING THE
Plug one end of the supplied coiled cord into
the handset's modular jack. Then connect it
to the jack on the left bottom of the base. Ô
S
U
P
ET
P THE
1. Hold down both
four seconds until
ENG ESP FRA
appear, with
2. Press
or
UP
DOWN
language, then press
LCD CONTRAST
confirm.
appear on the display, with
3. Press
or
UP
DOWN
contrast level (1-5), and press
ENTER AREA CODE
to confirm.
_ _ _
then
appears, with the first
flashing.
4. Press
and
UP
number of the area code, and press
END OF
to confirm the selection.
DELETE
5. Repeat step 4 to set the second and the
third digits.
S
ETTING THE
If you do not want to hear the phone ring,
slide
to
RINGER
OFF
calls with the ringer off, and you can still
answer calls if you hear another phone on
the same phone line ring. If you want to hear
the phone ring, set
S
ETTING THE
Slide
TONE/PULSE
of service you have. If you are not sure
which type you have, do this simple test.
1. Slide
TONE/PULSE
handset and listen for a dial tone.
2. Press any number except
phone requires that you dial an access
code (
, for example) before you dial an
9
outside number, do not press the
access code number.
• If the dial tone stops, you have touch-
tone service. Set the switch to
1
/
inches
4
H
ANDSET
HONE
and
for about
UP
DOWN
ENTER LANGUAGE
, then
ENG
flashing.
to select the desired
to
DELETE
1 2 3 4 5
and
3
flashing.
to select the
DELETE
appears,
_
to select the first
DOWN
R
INGER
. You can still make
to
or
.
RINGER
HI
LO
D
M
IALING
ODE
to the setting for the type
to
. Lift the
TONE
. If your
0
.
TONE
• If the dial tone continues, you have
pulse service. Set the switch to
.
PULSE
U
S
T
SING
PECIAL
ONE
S
ERVICES
Some computer services require tone
signals for communications. If you have
pulse service, you can still simulate special
tone service by following these steps.
1. Connect to the special service using
pulse dialing.
2. When the special service answers,
press * to temporarily switch to tone
dialing.
3. When you complete the call, hang up
and change the setting back to
U
M
/
SING THE
ASTER
S
S
ECONDARY
ETTING
(Master/Secondary) lets you easily
M/S
connect up to four system modules to the
same phone line, so CID and Call Waiting
information can be set to more than one
phone on that line.
1. Slide
to
.
M/S
M
2. Slide
on all (up to three) other
M/S
. Ô
systems to
S
3. Set one system to answer; set the
others to off.
OPERATION
M
C
AKING A
ALL
1. Pick up the handset and wait for a dial
tone.
2. Use the keypad to enter the number
you wish to dial. The number appears
on the display. Ô
3. When you complete your call, hang up
the handset. A few seconds later, the
number disappears, and the display
returns to normal.
R
C
ECEIVING A
ALL
When you receive a call, the phone rings
and the
indicator flashes.
NEW
the caller number appear on the display. To
answer the call, pick up the handset. Ô
T
IMER
This phone is designed with a clock timer to
count the off-hook time in seconds, up to
one hour. The timer appears on the display
and starts to count up when you dial a
number or answer an incoming call. Ô
U
F
SING
LASH
performs the electronic equivalent of
FLASH
a switchhook operation for special services,
.
PULSE
CALL#
and
Advertisement
