ˆ
Operation
Note: To use the speakerphone, you must
use the base keypad; to use the handset,
you must use the handset keypad.
MAKING A CALL
Using the Handset
To make a call, lift the handset and press
JWba
JWba
JWba
JWba
.
and current volume setting appear
TALK
on the handset's display.
pears on the base's display and CHARGE/IN
USE lights. Dial the number. You see the
number as you dial, then (after a few sec-
onds) the call's elapsed time.
Note: You can also dial the number before
you press
. If you make a mistake, re-
TALK
peatedly press
DELETE/CH
digit up to the wrong entry, then enter the
correct number. You can also press and hold
for more than one second to de-
DELETE/CH
lete the entire number.
To end a call, place the handset on the base
or press
.
TALK
Using the Speakerphone
To make or answer a call using the speaker-
phone, simply press
SPEAKER
pears on the base's display. Use the base's
keypad to dial the number. You see the num-
ber as you dial, then (after a few seconds)
the call's elapsed time.
Note: You can also dial the number before
you press
. If you make a mistake,
SPEAKER
repeatedly press
MUTE/DELETE
each digit up to the wrong entry, then enter
the correct number. You can also press and
hold
for more than one sec-
MUTE/DELETE
ond to delete the entire number.
14
To end a speakerphone call, press
again.
RECEIVING A CALL
When the phone receives a call,
appears. If you subscribe to Caller ID service
from your telephone company, the number
and name (if available) also appear.
To answer the call using the handset, lift the
>WdZi[j
>WdZi[j
>WdZi[j _d _d _d _d Ki[
>WdZi[j
Ki[
Ki[
Ki[
ap-
handset off the base and press
talk is on, just lift the handset or press any
key on the handset. To answer a call using
the speakerphone, press
ADJUSTING THE VOLUME
To adjust the volume you hear through the
to erase each
handset during a call, press
increase or
kc[ CWn_ckc
kc[
kc[
kc[
or
To adjust the speakerphone's volume, press
VOL
shows a bar graph of the volume level.
Note: If you press
the maximum or press
is low, the setting does not change and the
If[Wa[h
If[Wa[h
If[Wa[h
If[Wa[h
.
ap-
phone beeps three times.
SELECTING THE CHANNEL
The phone scans 20 channels (frequency
pairs used between the base and the hand-
set) and automatically selects a clear chan-
nel each time you make or receive a call. If
to erase
you hear other conversations or excessive
noise during a call, press
lect a different channel.
Note: If the handset is too far from the base,
the channel might not change and you hear
Operation
SPEAKER
9 9 9 9
to decrease the volume.
CWn_ckc
Lebkc[ >_]^
Lebkc[
>_]^
CWn_ckc
CWn_ckc
Lebkc[
Lebkc[
>_]^
>_]^
,
Lebkc[
Lebkc[ Bemý
Bemý
Lebkc[
Lebkc[
Bemý
Bemý
appears.
8 8 8 8
9 9 9 9
or
on the base. The display
8 8 8 8
while the volume is at
9 9 9 9
DELETE/CH
IYWdd_d]
IYWdd_d]
IYWdd_d]
IYWdd_d]
SPEAKER
?dYec_d]
?dYec_d] 9Wbb
?dYec_d]
?dYec_d]
9Wbb
9Wbb
9Wbb
. If auto
TALK
.
8 8 8 8
to
VOL/CID
Leb#
Leb#
Leb#
Leb#
Lebkc[ C[Z_kc
Lebkc[
C[Z_kc
Lebkc[
Lebkc[
C[Z_kc
C[Z_kc
,
,
while the volume
to se-
appears.