Parameter Table - YASKAWA L1000A Quick Start Manual

7

Parameter Table

This table below lists the most important parameters with
default settings appearing in bold type. Refer to the
Technical Manual for a complete list of parameters.
No. Name
Initialization Parameters
0: English
1: Japanese
2: German
3: French
4: Italian
5: Spanish
6: Portuguese
7: Chinese
8: Czech
9: Russian
10: Turkish
Language
A1-00
11: Polish
Selection
12: Greek
Note:1.
12 can be selected from an LCD operator
with version (REV) F or later. The version
number of the LCD operator's PRG
software is shown on the back of the digital
operator.
Note:2.
12 are available in drive software PRG:
7017 or later.
0: View and set parameters A1-01 and A1-
04 (U- parameters can also be
viewed)
1: User Parameters (access to a set of
Access Level
A1-01
parameters selected by the user, A2-01 to
Selection
A2-32)
2: Advanced Access (access to
view and set all parameters)
0: V/f Control
Control
2: Open Loop Vector Control
A1-02 Method
3: Closed Loop Vector Control
Selection
7: Closed Loop Vector Control for PM
0: No initialization
1110: User Initialize (parameter values must
Initialize
A1-03
be stored using parameter o2-03)
Parameters
2220: 2-wire initialization
5550: oPE04 error reset
Operation Mode Selection
0: Digital operator
Speed
1: Analog input terminals
b1-01 Reference
2: MEMOBUS/Modbus communications
Selection
3: Option Card
0: Digital operator
Up/Down
1: Digital input terminals
b1-02 Command
2: MEMOBUS/Modbus communications
Selection
3: Option Card
Output phase order with an Up command.
Phase Order
0: U-V-W
b1-14
Selection
1: U-W-V
YASKAWA ELECTRIC TOEP C710616 33G AC Drive L1000A - Quick Start Guide
Description
Language selection settings 8 to
Language selection settings 8 to
No. Name
Acceleration/ Deceleration Ramps
These parameters set the acceleration and
Acceleration/
deceleration ramps. Setting units are
C1- Deceleration
determined by parameter o1-03. Refer to
Ramps
page 23.
These parameters adjust the Jerk settings.
C2- Jerk Settings Setting units are determined by parameter
o1-03. Refer to page 23.
Slip Compensation
• Increase C3-01 if motor slip requires more
Slip
compensation (motor speed is lower than
C3-01 Compensation
speed reference).
Gain
• Decrease if slip is overcompensated.
Slip
• Decrease if the drive does not provide
Compensation
C3-02 motor slip compensation quickly enough.
Primary Delay
• Increase if motor oscillation occurs.
Time
Speed Control Loop Settings
Speed Control
C5-01
Loop Gain 1
Set the speed control loop responsiveness at
high speed.
Speed Control
C5-02
Loop I Time 1
Speed Control
C5-03
Loop Gain 2
Set the speed control loop responsiveness at
low speed during start.
Speed Control
C5-04
Loop I Time 2
Speed Control
Settings Sets the switching speed for speed loop
C5-07
Switching settings.
Speed
Speed Control
C5-13
Loop Gain 3
Set the speed control loop responsiveness at
low speed during stop.
Speed Control
C5-14
Loop I Time 3
Carrier Frequency
Carrier Sets the carrier frequency. Settings above
C6-03
Frequency the default requires output current derating.
Speed Reference
Speed Speed reference values for multi-speed
d1-01 to
Reference 1 to inputs. Setting units are determined by
d1-08
8 parameter o1-03. Refer to page 23.
0: Multi-speed references 1 to 8
1: Higher speed reference has
Speed
priority
Reference
d1-18
Selection
2: Leveling speed reference has priority
Mode
3: Multi-Speed References 2 to 8 (with
Multi-speed 1 selected the drive stops)
7 Parameter Table
Description
EN 37