Night Light Replacement; Pilot Injector And Orifice Replacement - Napoleon GDS25N-1 Installation And Operating Instructions Manual

 rebox top. Ensure they open freely, and close sealed.
movement is experienced.
• Check the gas control valve pilot and Hi / Lo knobs move freely (if equipped) – replace if any stiffness in
• Check for gas leaks on all gas connections up and downstream from the gas valve including the pilot tube
movement is experienced.
connections.
• Check for gas leaks on all gas connections up and downstream from the gas valve including the pilot tube
connections.

10.2 NIGHT LIGHT REPLACEMENT

10.2 NIGHT LIGHT REPLACEMENT
This appliance comes equipped with our "Night Light". This appliance comes equipped with our "Night Light".
10.2 NIGHT LIGHT REPLACEMENT
If in the event the lamp or lens needs to be replaced, follow these instructions. If in the event the lamp or lens needs to be replaced, follow these instructions.
This appliance comes equipped with our "Night Light".
Disconnect the two wire leads at the wire nut. Remove the four screws
Disconnect the two wire leads at the wire nut. Remove the four screws
If in the event the lamp or lens needs to be replaced, follow these instructions.
securing the accent light assembly from the relief door. Disassemble the securing the accent light assembly from the relief door. Disassemble the
Disconnect the two wire leads at the wire nut. Remove the four screws
light and the lamp now can be accessed
light and the lamp now can be accessed
securing the accent light assembly from the relief door. Disassemble the
Note: Do not handle the lamp (bulb) with bare fingers, protect with
Note: Do not handle the lamp (bulb) with bare fi ngers, protect with
light and the lamp now can be accessed
a clean dry cloth.
a clean dry cloth.
Note: Do not handle the lamp (bulb) with bare fi ngers, protect with
The lamp will pull straight out of the socket. Replace with Wolf Steel
The lamp will pull straight out of the socket. Replace with Wolf Steel
a clean dry cloth.
parts only, as lamp and lens are special "high temperature" products.
parts only, as lamp and lens are special "high temperature" products.
The lamp will pull straight out of the socket. Replace with Wolf Steel
When re-installing, ensure integrity of gasket seal. When re-installing, ensure integrity of gasket seal.
parts only, as lamp and lens are special "high temperature" products.
THE FIREBOX MUST BE SEALED.
THE FIREBOX MUST BE SEALED. When re-installing, ensure integrity of gasket seal.
When re-assembling the light assembly, care must be taken
THE FIREBOX MUST BE SEALED.
When re-assembling the light assembly, care must be taken
with all gaskets.
When re-assembling the light assembly, care must be taken
with all gaskets.
"Light Leakage" from above the cast doors may with all gaskets.
"Light Leakage" from above the cast doors may
"Light Leakage" from above the cast doors may
be noticed. The holes in the lamp housing are
be noticed. The holes in the lamp housing are
be noticed. The holes in the lamp housing are
necessary for ventilation and must not be covered.
necessary for ventilation and must not be covered.
necessary for ventilation and must not be covered.
10.3

10.3 PILOT INJECTOR AND ORIFICE REPLACEMENT

PILOT INJECTOR AND ORIFICE REPLACEMENT
10.3 PILOT INJECTOR AND ORIFICE REPLACEMENT
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RAN OUT
This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL
This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL
This must be carried out by an AUTHORIZED REPRESENTATIVE OF WOLF STEEL
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the
LTD. or a QUALIFIED GAS INSTALLER in accordance with local codes or in the
absence of local codes with the requirements of the provincial / state authorities having
absence of local codes with the requirements of the provincial / state authorities having
absence of local codes with the requirements of the provincial / state authorities having
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
jurisdiction and in accordance with the requirements of the CAN1-B149 Installation Code
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
in Canada and the ANSI Z223.1 National Fuel Gas Code in the United States.
Turn off the electrical and gas supply to the appliance.
A.
A. Turn off the electrical and gas supply to the appliance.
A. Turn off the electrical and gas supply to the appliance.
Remove the cast front, glass viewing door and log set.
B.
B. Remove the cast front, glass viewing door and log set.
B. Remove the cast front, glass viewing door and log set.
Remove the 2 securing screws. Slide the burner assembly to the right and lift
C.
C.
Remove the 2 securing screws. Slide the burner assembly to the right and lift
C. Remove the 2 securing screws. Slide the burner assembly to the right and lift
out.
out.
out.
Using a deep socket wrench, remove the main burner orifice. A back-up
D. D. Using a deep socket wrench, remove the main burner ori ce. A back-up wrench
D. Using a deep socket wrench, remove the main burner ori ce. A back-up wrench
wrench must be used on themanifold, located below the housing to ensure that
must be used on themanifold, located below the housing to ensure that the
must be used on themanifold, located below the housing to ensure that the
the aluminum tubing does not twist or kink. Replace the correct burner orifice aluminum tubing does not twist or kink. Replace the correct burner ori ce using
aluminum tubing does not twist or kink. Replace the correct burner ori ce using
pipe thread compound.
using pipe thread compound.
pipe thread compound.
E. Loosen nut and replace with appropriate injector
Loosen nut and replace with appropriate injector
E.
E. Loosen nut and replace with appropriate injector
F.
Reinstall the burner ensuring that the Venturi tube  ts over the ori ce.
Reinstall the burner ensuring that the Venturi tube fits over the orifice.
F.
F. Reinstall the burner ensuring that the Venturi tube  ts over the ori ce.
G. Turn on the gas supply and check for gas leaks by brushing on a soap and water solution.
Turn on the gas supply and check for gas leaks by brushing on a soap and
G.
G. Turn on the gas supply and check for gas leaks by brushing on a soap and water solution.
Do not use open fl ame.
water solution. Do not use open flame.
Do not use open fl ame.
H. Replace the log set. Then light the pilot and main burner to ensure that the gas lines have
Replace the log set. Then light the pilot and main burner to ensure that the gas
H.
H. Replace the log set. Then light the pilot and main burner to ensure that the gas lines have
been purged.
lines have been purged.
been purged.
I.
Replace the glass viewing door and cast front. Turn on the electrical supply to the appliance.
Replace the glass viewing door and cast front. Turn on the electrical supply to
I.
I. Replace the glass viewing door and cast front. Turn on the electrical supply to the appliance.
the appliance.
WARNING
WARNING
!
!
WARNING
!
WITH THE GLASS DOOR OPEN OR REMOVED.
WITH THE GLASS DOOR OPEN OR REMOVED.
WITH THE GLASS DOOR OPEN OR REMOVED.
37.1C
37.1C
RAIL
RAIL
41
WIRE NUT
WIRE NUT
SHIELD
SHEILD
SHEILD
COVER PLATE
COVER PLATE
GASKET
GASKET
GLASS LENS
GLASS LENS
GASKET
GASKET
RELIEF
DOOR
RELIEF
RAIL
DOOR
RAIL
ORIFICE ORIFICE
LOCATION
LOCATION
BURNER
BURNER
ASSEMBLY
ASSEMBLY
W415-1332 / A / 11.21.14
W415-1332 / A / 11.21.14
W415-2207 / A / 08.28.17
EN
EN