Remote Control; Hdmi - Pioneer VSX-LX60 Operating Instructions Manual

Additional information

Remote control

Symptom
Cannot be remote controlled.
Other components can't be
operated with the system remote.
The SR cable is connected, but
the connected components can't
be operated with the remote.

HDMI

Symptom
The HDMI indicator blinks
continuously.
No picture or sound.
No picture.
No sound, or sound suddenly
ceases.
Noisy or distorted picture.
HDCP ERROR shows in the
display.
Remedy
• Try replacing the batteries in the remote control (see Loading the batteries on page 6).
• Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see Operating range
of remote control unit on page 24).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this unit's
sensor on page 81).
• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
• Reinsert the SR cable, making sure it's connected to the right jack (see Using this receiver with a Pioneer
plasma display on page 61).
• Make sure that there is an analog or HDMI connection between the units. This is necessary for the SR
feature to work.
• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.
Remedy
• Check all the points below.
• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component, S-video or composite video jacks.
• Depending on the connected source component, it's possible that it will not work with this receiver (even
if it is HDCP-compatible). In this case, connect using the component, S-video or composite video jacks
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV or plasma display, try adjusting the resolution, DeepColor or
other setting for your component.
• If 'NOT SUPPORT' appears in the receiver's display, try adjusting the resolution, DeepColor or other
setting for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio output.
• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to THROUGH, you
cannot hear audio output from all channels. In this case, make a digital or analog audio connection.
• To output signals in DeepColor, use an HDMI cable (compliant with Version 1.3a, Category 2) to connect
this receiver to a component or TV with the DeepColor feature.
• Try changing the Resolution setting (in Setting the Video options on page 71).
• Check that the HDMI AV setting is set to AMP/THROUGH.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-video or composite), then start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
• Check whether or not the connected component is compatible with HDCP. If it is not compatible with
HDCP, reconnect the source device using a different type of connection (component, S-video or composite).
Some components that are compatible with HDCP still cause this message to be displayed, but so long as
there is no problem with displaying video, this is not a malfunction.
14
87
En