Page 2
Precautions Do not install the camera near electric or magnetic fields. Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere with camera operation. Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination beyond the capability of the camera to compensate. Keep the power cable away from water and other liquids and never touch the power cord with wet hands. Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric shock. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera. Do not operate the camera beyond the specified temperature, humidity or power source ratings. This camera is suitable for indoor operation only. Use the camera at temperatures within ‐10°C~50°C (‐14°F~122°F) and humidity less than 80%; this device is not rated as submersible. The input power source is 12VDC. Be sure to connect the proper + / ‐ polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail, and such damage is not covered by the warranty. Mounting. Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind, snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional support for the camera. ...
Page 3
afety No otice Federal l Communic cation Com mission Int terference S Statement This equ uipment ha as been test ed and foun nd to comp ly with the limits for a Class A dig ital device, pursuan nt to Part 15 5 of the FCC C Rules. The ese limits ar re designed to provide reasonable e protection n against harmful int terference i n a residen tial installat tion. This eq quipment g generates us ses and can radiate radio frequ uency energ gy and, if no ot installed a...
The EMD93 35F with its 3 Axis rotat tion design allows wall l or ceiling m mounting fl exibility in a an IP66 weather re esistant. The e EMD935F comes with h 6 IR LEDs, , supporting g up to 10m m (~33ft.) IR distance in night vision n, also can w work in both h indoor an d outdoor e environmen nts. The EM D935F supp ports both NTSC and P PAL scannin g systems, w which can b...
MD935F Out tdoor Mobi ile IR Mini B Ball Camera 2. Cab le Descri iption No. me Desc criptions 1 wer Cable Conn nects to a 1 12VDC powe er source. 1080 0p, 720p an nd 960H out tput, using a a 75 Ohm B BNC‐type 2 Vide eo Output coax xial cable. Opti onal power r pigtail cab le. The red wire is posi itive (+); 3 DC P Power Pigta ail Cable whil e the black ...
MD935F Out tdoor Mobi ile IR Mini B Ball Camera 3. Insta allation 3.1 In stallation and Adju ustment For Ceiling M Mount / Wa all Mount us sers: Stick t he template e plate on t the position n where you u want to atta ach the cam mera, drill th ree holes o on the temp late plate a and insert th he supplied hree ancho ors. Drill ano other hole in n the temp late plate o nly if you w want to wire e the cables hrough the wall / ceilin ng. ...
Page 8
MD935F Out tdoor Mobi ile IR Mini B Ball Camera Screw the ca amera base e plate to th e wall / ceil ling using th he supplied three screw ws. Screw the ca amera body y back to ba ase plate wi th supplied hexagon w wrench , par rticularly noted the tw wo ways on cable wirin ng as follow ing illustrat ion: Wire the e Cables fro om the Side e ...
Page 9
MD935F Out tdoor Mobi ile IR Mini B Ball Camera Connect the e camera to the 12VDC C power sou rce using th he supplied DC power pigtail cable e or power ad dapter, while e connectin ng the video o‐out cable to the mon itor. After selecte ed the desir red angle, t hen tighten n the two sc crews using the supplie ed hexagon wrench , wh hich close to o base plate e and one o n each side of camera. . ...
Page 10
MD935F Out tdoor Mobi ile IR Mini B Ball Camera 4. Con figuratio on in the OSD Me enu You can con nfigure cam mera setting s in the OSD D menu from m DVR end . For details s on the OSD D menu structure as s below: No. Mai in ub Menu Sub Menu / / Function 1 s anual NTSC: 1/30 0, 1/60, FL LK, 1/240, 1/480, ...
Page 11
MD935F Out tdoor Mobi ile IR Mini B Ball Camera pecial 2 * pecial 1 * Blue 0‐100 anual Red 0‐100 WB 0‐60 D→N(Delay y) xt 0‐60 N→D(Delay y) 1‐255 D→N(AGC) ) D→N(Delay y) 0‐60 uto N→D(AGC) ) 1‐255 y & N→D(Delay y) 0‐60 5 Nigh ht olor Burst Off/On n ...
Page 12
MD935F Out tdoor Mobi ile IR Mini B Ball Camera me 1‐15 Defau lt Off Select ea1,Area2,A Area3,Area4 4 f Position, S Size,↑,↓, lor →,← Displa y Position, S Size,↑,↓, osaic →,← rivacy On Position, S Size,↑,↓, v →,← hite, Black, Red, Blue, C CYAN, Color llow, Green 00,0.75,0.50 0, Trans 25 ...
Page 13
MD935F Out tdoor Mobi ile IR Mini B Ball Camera Baud Rate 2400,4 4800,9600,1 19200 ,3840 00 Off Level 0‐1 10 harpness Auto Start A AGC 0‐2 255 End AG GC 0‐2 255 Black Level 0‐6 60 CRT Blue G Gain 0‐1 100 Red G ain 0‐2 255 8 Adju ust er,0.45,0.50 0,0.55,0.60, ,0.65,0.70,0 onitor ...
MD935F Out tdoor Mobi ile IR Mini B Ball Camera 5. Specif fications P/N MD935F Pickup De evice /2.9" Sony 2 2.24M pixe ls CMOS Video For mat TSC and PA AL(can be sw witched via OSD) Effective P Pixels 920 (H)x108 80(V) Scanning S System rogressive S Scan Sensitivity y 0 lux with IR on Electronic c Shutter UTO/Manu ual (X30~1/5 50,000)/FLK K Gamma C orrection ...
Page 15
TEL: +81 3 5 5625 8188 844 8838 FAX: +81 3 5 5625 8189 us.com www.everfo ocus.co.jp ocus.com info@everfo ocus.co.jp Ihr EverFocus Pr rodukt wurde Your EverFocus p product is designed an entwickelt und h hergestellt mit manufactured wi th high quality materia qualitativ hochw wertigen Materialien and components...