Page 1: Command Reference
Command Reference MODEL : CT-D150 CT-D151 CT-E351 CT-E651 CT-S251 CT-S280 CT-S281 CT-S300 CT-S310 CT-S310II CT-S601(II) CT-S651(II) CT-S801(II) CT-S851(II) CT-S2000 CT-S4000 CT-P29x Series Revision 0.24 2017/6/1...
Page 2 Supported CT-D150 and CT-E351 0.24 2017/6/1 Supported CT-D151 and CT-E651 ESC/POS is a trade mark of SEIKO EPSON Corporation. CITIZEN is a registered trade mark of CITIZEN WATCH CO., LTD., Japan. CITIZEN es una marca registrada de CITIZEN WATCH CO., LTD., Japón.
Page 3: Table Of Contents
2.1.7 CT-S4000 ..............................28 2.1.8 CT-S601/651/801/851 ..........................32 2.1.9 CT-S601 II/CT-S651 II/CT-S801 II/CT-S851 II ................... 36 2.1.10 CT-S251 ..............................40 2.1.11 CT-P29x series ............................44 2.1.12 CT-D150 ..............................47 2.1.13 CT-E351 ..............................50 2.1.14 CT-D151 ..............................53 2.1.15 CT-E651 ..............................57 ..........................61 2.2 C...
Page 4 ESC & s n m [ a [p] s x a ] m-n+1 ........................74 ESC - n ................................76 ESC ? n ................................77 ESC E n ................................78 ESC G n ................................79 ESC M n ................................80 ESC R n ................................
Page 5 GS ^ n1 n2 n3 ..............................150 2.2.11 Cutter Commands ..........................151 ESC i ................................. 151 ESC m ................................152 GS V m --- (1) ..............................153 GS V m n --- (2) ..............................153 2.2.12 Bar Code Commands ........................154 GS H n ................................
Page 6 GS C 0 m n ................................ 198 GS C 1 n1 n2 n3 n4 n5 n6 ..........................199 GS C 2 n1 n2 ..............................200 GS C ; n1 ; n2 ; n3 ; n4 ; n5 ; ..........................201 GS c ..................................
Page 7 2.2.18 Gray Scale Commands ........................380 GS ( z GrayBMP , ............................... 380 GS ( z WaterMark,size,start,kc1,kc2,pass,feed,repeat ..................382 2.2.19 Other Commands ..........................384 DLE ENQ n ............................... 384 DLE DC4 fn m t (Specification of fn = 1) ......................385 DLE DC4 fn d1...d7 (Specification of fn = 8) .....................
Page 8 4.1.10 CT-S801 II/CT-S851 II ......................... 447 4.1.11 CT-S601 II/CT-S651 II ......................... 450 4.1.12 CT-S251 ............................. 452 4.1.13 CT-P29x series ..........................454 4.1.14 CT-D150 ............................. 456 4.1.15 CT-E351 ............................. 458 4.1.16 CT-D151 ............................. 460 4.1.17 CT-E651 ............................. 462 ...................... 464 4.2 D...
Page 9: Outline
BASIC programming is explained. Example 1 Let’s print a character string “CITIZEN” in enlarged (double-height, double-width) and in normal format. Program coding The Control Command shows that the command name for setting the size of a character is GS !. Let’s make a program using this code.
Page 10: Detail
2. DETAIL 2.1 ESC/POS Command List 2.1.1 CT-S280 Print Control Commands Commands Function MODE GS P Page Printing and paper feed S・P Back to printing S・P Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) ESC FF Printing data in PAGE MODE ○...
Page 11 Print Position Commands Command Function MODE GS P Page Horizontal tab S・P ○ ESC $ Specifying the absolute positions S・P ESC D Setting horizontal tab position S・P ESC T Selecting the character printing direction in PAGE MODE ○ ESC W Defining the print area in PAGE MODE ○...
Page 12 Bar Code Commands Command Function MODE GS P Page GS H Selecting of printing position of HRI characters S・P GS f Selecting the font of HRI characters S・P GS h Specifying the height of the bar code S・P GS k Printing the bar code S・P GS w...
Page 13: Ct-S281
2.1.2 CT-S281 Print Control Commands Commands Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark and paper feeding to the top of the print position (with Black mark/Label paper selected) ESC FF Printing data in PAGE MODE...
Page 14 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 15 Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S・P FS & Setting Kanji mode S・P FS - Setting/Canceling Kanji underline S・P FS ． Canceling Kanji mode S・P FS 2 Defining external character S・P FS C Selecting Kanji code system...
Page 16: Ct-S300
2.1.3 CT-S300 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 17 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 18 Commands for Non-volatile Memory Command Function MODE GS P Page FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S・P FS &...
Page 19: Ct-S310
2.1.4 CT-S310 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 20 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 21 Commands for Non-volatile Memory Command Function MODE GS P Page FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S・P FS &...
Page 22: Ct-S310Ii
2.1.5 CT-S310II Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 23 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 24 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 25: Ct-S2000
2.1.6 CT-S2000 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 26 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 27 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 28 Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC = Data input control S・P ESC @ Initializing the printer S・P ESC L Selecting PAGE MODE ESC S Selecting STANDARD MODE ESC p...
Page 29: Ct-S4000
2.1.7 CT-S4000 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 30 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 31 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 32 Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC = Data input control S・P ESC @ Initializing the printer S・P ESC L Selecting PAGE MODE ESC S Selecting STANDARD MODE ESC p...
Page 33: Ct-S601/651/801/851
2.1.8 CT-S601/651/801/851 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 34 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 35 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 36 Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC = Data input control S・P ESC @ Initializing the printer S・P ESC L Selecting PAGE MODE ESC S Selecting STANDARD MODE ESC p...
Page 37: Ct-S601 Ii/Ct-S651 Ii/Ct-S801 Ii/Ct-S851 Ii
2.1.9 CT-S601 II/CT-S651 II/CT-S801 II/CT-S851 II Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 38 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 39 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L GS D Definition to NV Memory of Windows Bitmap FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function...
Page 40 Gray Scale Commands Command Function MODE GS P Page Print of the gray scale raster graphics （_z_GrayBMP Specifying WaterMark Printing WaterMark Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC =...
Page 41: Ct-S251
2.1.10 CT-S251 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) ESC FF Printing data in PAGE MODE ○...
Page 42 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 43 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L GS D Definition to NV Memory of Windows Bitmap FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function...
Page 44 Gray Scale Commands Command Function MODE GS P Page Print of the gray scale raster graphics （_z_GrayBMP Specifying WaterMark Printing WaterMark Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC =...
Page 45: Ct-P29X Series
2.1.11 CT-P29x series Print Control Commands Command Function MODE GS P Page Printing and paper feed S･P Back to printing S･P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 46 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S･P ○ ESC 3 Setting line feed rate of minimum pitch S･P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S･P GS *...
Page 47 Kanji Control Commands Command Function MODE GS P Page FS ! Collectively setting Kanji print mode S・P FS & Setting Kanji mode S・P FS - Setting/Canceling Kanji underline S・P FS ． Canceling Kanji mode S・P FS 2 Defining external character S・P FS C Selecting Kanji code system...
Page 48: Ct-D150
2.1.12 CT-D150 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the...
Page 49 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 50 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 51: Ct-E351
2.1.13 CT-E351 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P (1)Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) (2)Printing of Black mark/Label paper and feeding paper to the top of the print position (with Black mark/Label paper selected) ESC FF...
Page 52 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 53 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function MODE GS P Page...
Page 54: Ct-D151
2.1.14 CT-D151 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) ESC FF Printing data in PAGE MODE ○...
Page 55 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 56 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L GS D Definition to NV Memory of Windows Bitmap FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function...
Page 57 Gray Scale Commands Command Function MODE GS P Page Print of the gray scale raster graphics （_z_GrayBMP Specifying WaterMark Printing WaterMark Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC =...
Page 58: Ct-E651
2.1.15 CT-E651 Print Control Commands Command Function MODE GS P Page Printing and paper feed S・P Back to printing S・P Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) ESC FF Printing data in PAGE MODE ○...
Page 59 Line Feed Span Commands Command Function MODE GS P Page ESC 2 Specifying initial line feed rate S・P ○ ESC 3 Setting line feed rate of minimum pitch S・P Bit Image Commands Command Function MODE GS P Page ESC * Specifying the bit image mode S・P GS *...
Page 60 Commands for Non-volatile Memory Command Function MODE GS P Page GS ( L Specifying graphics data GS 8 L GS D Definition to NV Memory of Windows Bitmap FS p Printing the download NV bit images FS q Defining the download NV bit image Kanji Control Commands Command Function...
Page 61 Gray Scale Commands Command Function MODE GS P Page Print of the gray scale raster graphics （_z_GrayBMP Specifying WaterMark Printing WaterMark Other Commands Command Function MODE GS P Page DLE ENQ Real-time request to printer S・P DLE DC4 Outputting specified pulse in real-time/Buffer clear S・P 385/386 ESC =...
Page 62: Command Details
2.2 Command Details 2.2.1 Description of Items XXXX support model [Function] The name of a command. [Code] The string of codes comprising the command is represented by < >H for hexadecimal numbers, < >B for binary numbers, and < > for decimal numbers, [ ] k denotes the number of repetition of “k” times. [Range] Indicates the values (setting range) of arguments of the command.
Page 63: Print Control Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.2 Print Control Commands [Function] Printing and paper feed [Code] <0A>H [Outline] [The specification which is common to the model] • Prints data inside the print buffer and feeds paper based on the line feed amount having been set.
Page 64 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Function] Back to printing [Code] <0D>H [Outline] [The specification which is common to the model] (1) MSW* 1-5 OFF: This command is ignored. (2) MSW 1-5 ON: The same operation as LF is executed.
Page 65: Ff (At Selection Of
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FF (At selection of PAGE MODE) [Function] Printing in PAGE MODE and returning to STANDARD MODE (at the selection of PAGE MODE) [Code] <0C>H...
Page 66: Ff (Valid Only For Black Mark/Label Specification)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 (valid only for Black mark/Label specification) [Function] At selection of Black mark/Label paper (valid only for Black mark/Label specification) [Outline] [The specification which is common to the model] •...
Page 67: Esc Ff
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC FF [Function] Printing data in PAGE MODE [Code] <1B>H<0C>H [Outline] [The specification which is common to the model] • Executes a batch printout of the data mapped in the entire print area in PAGE MODE.
Page 68: Esc J N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC J n [Function] Printing and feeding paper in minimum pitch [Code] <1B>H<4A>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 69: Esc D N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC d n [Function] Printing and feeding the paper by “n” lines [Code] <1B>H<64>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] Prints data in the print buffer and feeds paper by “n”...
Page 70: Print Character Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.3 Print Character Commands [Function] Canceling print data in PAGE MODE [Code] <18>H [Outline] [The specification which is common to the model] Erases all data contained in the currently effective print area in PAGE MODE.
Page 71: Esc Sp N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC SP n [Function] Setting the right spacing of the character [Code] <1B>H<20>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 72: Esc ! N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC ! n [Function] Collectively specifying the printing mode [Code] <1B>H<21>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] Printing mode is assigned.
Page 73 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Caution] • With double height and double width being specified simultaneously, quadruple characters are created. • An underline is attached to the full character width, which, however, is not attached to the part having been skipped by the horizontal tab (HT).
Page 74: Esc % N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC % n [Function] Specifying/canceling download character set [Code] <1B>H<25>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] Specifying/canceling download characters.
Page 75: Esc & S N M [ A [P] S X A ] M-N+1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC & s n m [ a [p] s x a ] m-n+1 [Function] Defining the download characters [Code] <1B>H<26>H<s>H<n>H<m>H [<a>H<p1>H<p2>---<ps×a>] m-n+1 [Range] s=3(Font A, B), s=2(Font C) 32≤n≤m≤126...
Page 76 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Example] 12dot 24dot Font A Create each data bit by setting “1” for a printed dot and “0” for an unprinted dot. [Sample Program] Refer to Sample Program and Print Results for ESC %.
Page 77: Esc - N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC - n [Function] Specifying /canceling underline [Code] <1B>H<2D>H<n> [Range] 0≤n≤2, 48≤n≤50 [Outline] [The specification which is common to the model] • Specifying /canceling an underline.
Page 78: Esc ? N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC ? n [Function] Deleting download characters [Code] <1B>H<3F>H<n> [Range] 32≤n≤126 [Outline] [The specification which is common to the model] Deletes the downloaded characters of specified code.
Page 79: Esc E N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC E n [Function] Specifying/canceling emphasis printing [Code] <1B>H<45>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • Specifying/canceling the emphasized characters.
Page 80: Esc G N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC G n [Function] Specifying/canceling double strike printing [Code] <1B>H<47>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • Specifying /canceling the double strike printing.
Page 81: Esc M N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC M n [Function] Selection of character fonts [Code] <1B>H<4D>H<n> [Range] 0≤n≤2, 48≤n≤50 [Outline] [The specification which is common to the model] • Selects character fonts.
Page 82: Esc R N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC R n [Function] Selecting the international character set [Code] <1B>H<52>H<n> [Range] [The specification which depend on the model] CT-S280/CT-S300 0≦n≦13 CT-S281/CT-S310/CT-S2000/CT-S4000/CT-P29x series 0≦n≦15...
Page 83: Esc V N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC V n [Function] Specifying/canceling 90°-right-turned characters [Code] <1B>H<56>H<n> [Range] 0≤n≤1, 48≤n≤49 [Outline] [The specification which is common to the model] • Specifying/canceling 90°-right-turned characters.
Page 84: Esc T N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC t n [Function] Selecting the character code table [Code] <1B>H<74>H<n> [Range] 0≤n≤9, 16≤n≤19, n=26, 40, 255 [The specification which depend on the model]...
Page 85: Esc { N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC { n [Function] Specifying/canceling the inverted characters [Code] <1B>H<7B>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • “n” is valid only for the lowest bit (n0).
Page 86: Esc ˜ J N (Valid In Cbm-270-Compatible Mode)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC ˜ J n (Valid in CBM-270-Compatible Mode) [Function] Specifies/cancels printing in red (black-based paper) [Code] <1B>H<7E>H<4A>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 87: Esc ˜ J N (Valid In Cbm1000-Compatible Mode)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC ˜ J n (Valid in CBM1000-Compatible Mode) [Function] Specifies/cancels printing in red (black-based paper) [Code] <1B>H<7E>H<4A>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 88: Dc3 N (Valid In Cbm-270-Compatible Mode)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 DC3 n (Valid in CBM-270-Compatible Mode) [Function] Specifies/cancels printing in red (black-based paper) [Code] <13>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 89 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Default] [Sample Program] LPRINT CHR$(&H13); CHR$(1); LPRINT "AAAAA"; CHR$(&HA); LPRINT CHR$(&H13); CHR$(0); LPRINT "AAAAA"; CHR$ (&HA); [Print Results] Red printing ＡＡＡＡＡ Black printing ＡＡＡＡＡ...
Page 90: Dc3 N (Valid In Cbm1000-Compatible Mode)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 DC3 n (Valid in CBM1000-Compatible Mode) [Function] Specifies/cancels printing in red (black-based paper) [Code] <13>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 91: Gs ! N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ! n [Function] Specifying the character size [Code] <1D>H<21>H<n> [Range] 0≤n≤255 Where: 1≤vertical magnification≤8, 1≤horizontal magnification≤8 [Outline] [The specification which is common to the model] •...
Page 92 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Caution] [The specification which is common to the model] • This command is valid for all characters (alphanumeric, kana, and kanji) except for HRI characters.
Page 93: Gs B N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS B n [Function] Specifying/canceling the black/white inverted printing [Code] <1D>H<42>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • This command specifies or cancels the black/white inverted printing.
Page 94: Gs B N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS b n [Function] Specifying/canceling the smoothing [Code] <1D>H<62>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • This command specifies or cancels the smoothing.
Page 95: Print Position Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.4 Print Position Commands [Function] Horizontal tab [Code] <09>H [Outline] [The specification which is common to the model] • Shifts the printing position to the next horizontal tab position.
Page 96: Esc $ N1 N2
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC $ n1 n2 [Function] Specifying the absolute positions [Code] <1B>H<24>H<n1><n2> [Range] 0≤n1≤255 0≤n2≤255 [Outline] [The specification which is common to the model] • The printing start position is specified by the absolute position from the left margin with the number of dots divided by 256 and quotient specified as “n2”...
Page 97: Esc D [N] K Null
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC D [n] k NULL [Function] Setting horizontal tab position [Code] <1B>H<44>H [<n>] k<00>H [Range] 1≤n≤255 0≤k≤32 [Outline] [The specification which is common to the model] •...
Page 98: Esc T N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC T n [Function] Selecting the character printing direction in PAGE MODE [Code] <1B>H<54>H<n> [Range] 0≤n≤3, 48≤n≤51 [Outline] [The specification which is common to the model] •...
Page 99: Esc W Xl Xh Yl Yh Dxl Dxh Dyl Dyh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC W xL xH yL yH dxL dxH dyL dyH [Function] Defining the print area in PAGE MODE [Code] <1B>H<57>H<xL><xH><yL><yH><dxL><dxH><dyL><dyH> 0≤xL, xH, yL, yH, dxL, dxH, dyL, dyH ≤255...
Page 100 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 • The maximum horizontal length that can the printing width. (Refer to the below Table) [The specification which is common to the model • The maximum setting length in the vertical direction is as follows...
Page 101: Esc \ Nl Nh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC \ nL nH [Function] Specifying the relative position [Code] <1B>H<5C>H<nL><nH> [Range] 0≤nL≤255 0≤nH≤255 [Outline] [The specification which is common to the model] • This command specifies the next print start position in a relative position with respect to the current position.
Page 102: Esc A N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC a n [Function] Aligning the characters [Code] <1B>H<61>H<n> [Range] 0≤n≤2, 48≤n≤50 [Outline] [The specification which is common to the model] • All the printed data within one line are aligned in the specified position.
Page 103: Gs $ Nl Nh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS $ nL nH [Function] Specifying the absolute position of character vertical direction in PAGE MODE [Code] <1D>H<24>H<nL><nH> [Range] 0≤nL≤255, 0≤nH≤255 [Outline] [The specification which is common to the model] •...
Page 104: Gs L Nl Nh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS L nL nH [Function] Setting the left margin [Code] <1D>H<4C>H<nL><nH> [Range] 0≤nL≤255, 0≤nH≤255 [Outline] [The specification which is common to the model] • This command sets the left margin specified by nL and nH.
Page 105: Gs W Nl Nh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS W nL nH [Function] Setting the print area width [Code] <1D>H<57>H<nL><nH> [Range] 0≤nL≤255 0≤nH≤255 [Outline] [The specification which is common to the model] •...
Page 106 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 (2) If a sufficient area cannot be provided as a result of step (1), the print area is extended toward the left (so, the left margin is decreased).
Page 107: Gs \ Nl Nh
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS \ nL nH [Function] Specifying the relative vertical position of a character in PAGE MODE [Code] <1D>H<5C>H<nL><nH> [Range] 0≤nL≤255, 0≤nH≤255 [Outline] [The specification which is common to the model] •...
Page 108: Line Feed Span Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.5 Line Feed Span Commands ESC 2 [Function] Specifying 1/6-inch line feed rate [Code] <1B>H<32>H [Outline] [The specification which depend on the model] CT-S280/CT-S281/CT-S300/CT-S310/CT-P29x series The line feed rate per line is specified by 1/6 inch.
Page 109: Esc 3 N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC 3 n [Function] Setting line feed rate of minimum pitch [Code] <1B>H<33>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] Sets the line feed width per line to [n×basic calculation pitch] inches.
Page 110: Bit Image Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.6 Bit Image Commands ESC * m n1 n2 [d] k [Function] Specifying the bit image mode [Code] <1B>H<2A>H<m>H<n1><n2> [<d>] k [Range] m=0, 1, 32, 33 0≤n1≤255, 0≤n2≤3...
Page 111 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [The specification which depend on the model] (1) - (4) unit: dpi paper print support model width width CT-S4000 112mm 104mm CT-S4000 112mm 90mm...
Page 112: Gs * N1 N2 [D] N1Xn2X8
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS * n1 n2 [d] n1xn2x8 [Function] Defining the download bit image [Code] <1D>H<2A>H<n1><n2> [<d>] n1×n2×8 [Range] 1≤n1≤255 1≤n2≤48 n1×n2≤1536 [Outline] [The specification which is common to the model] •...
Page 113: Gs / M
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS / m [Function] Printing the downloaded bit image [Code] <1D>H<2F>H<m> [Range] 0≤m≤3, 48≤m≤51 [Caution] [The specification which is common to the model] • Prints downloaded bit image in a mode specified by “m”.
Page 114: Gs V 0 M Xl Xh Yl Yh D1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS v 0 m xL xH yL yH d1 ... dk [Function] Printing of raster bit image [Code] <1D>H<76>H<30>H<m><xL><xH><yL><yH> [<d>] k [Range] 0≤m≤3, 48≤m≤51, 0≤xL≤255, 0≤xH≤255, 0≤yL≤255, 0≤yH≤8, 0≤d≤255,...
Page 115 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Example] When xL + xH × 256 = 64 (xL+xH×256)×8 dots = 512 dots ドトドト yL+yH×256 dots - 114 -...
Page 116: Status Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.7 Status Commands DLE EOT n [Function] Sending status in real-time [Code] <10>H<04>H<n> [Range] 1≤n≤4 [Outline] [The specification which is common to the model] •...
Page 117 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 118 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 119 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 120 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300/CT-S310 (3) Status caused by an error (when n = 3 is specified) (1) Printer status (When n = 1 is specified) Status Hex.
Page 121 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300/CT-S310 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 122 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 123 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 (3) Status caused by an error (when n = 3 is specified) (1) Printer status (When n = 1 is specified) Status Hex.
Page 124 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 125 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 (3) Status caused by an error (when n = 3 is specified) (1) Printer status (When n = 1 is specified) Status Hex.
Page 126 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 127 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II)/CT-S601(II)/CT-S651(II) (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 128 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II)/CT-S601(II)/CT-S651(II) (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 129 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 130 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 131 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 132 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Fixed Fixed Fixed Paper found by Paper-end Sensor...
Page 133 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 (3) Status caused by an error (when n = 3 is specified) (1) Printer status (When n = 1 is specified) Status Hex.
Page 134 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 135 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 136 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 137 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 (1) Printer status (When n = 1 is specified) (3) Status caused by an error (when n = 3 is specified) Status Hex.
Page 138 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 (4) Continuous paper detector status (When n = 4 is specified) Status Hex. Decimal Fixed Fixed Paper found by Paper Near-end Sensor Paper not found by Paper Near-end Sensor...
Page 139: Esc U N(Valid In Cbm1000-Compatible Mode)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC u n (Valid in CBM1000-Compatible Mode) [Function] Sending the peripheral device status [Code] <1B>H<75>H<n> [Outline] [The specification which is common to the model] •...
Page 140: Esc V
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC v [Function] Transmission of printer status [Code] <1B>H<76>H [Outline] [The specification which is common to the model] • Transmits current printer status. [Caution] [The specification which is common to the model] •...
Page 141: Gs A N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS a n [Function] Enabling/disabling ASB (Automatic Status Back) [Code] <1D>H<61>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • This command selects the status item to be addressed by ASB (Automatic Status Back.) Status Item Addressed by ASB Hex.
Page 142 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [The specification which depend on the model] CT-S280/CT-S281/CT-P29x series • Bit 2 of the 1st byte (printer information) of the status sent in 4 bytes is set to 00H because drawer is not supported.
Page 143 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 (2) 2nd byte (Error occurrence information) Status Hex. Decimal Undefined Undefined No Mechanism error occurred. No BM detection error occurred.(only when BM paper is selected) No presenter error occurred.
Page 144 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 (4) 4th byte (Paper Sensor information) In case of MSW3-7 ON Status Hex. Decimal Undefined Undefined Undefined Undefined Unused Undefined Undefined Unused In case of MSW3-7 OFF (CBM1000 non-compatible mode) Status Hex.
Page 145: Gs R N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS r n [Function] Sending status [Code] <1D>H<72>H<n> [Range] [The specification which depend on the model] CT-S280/CT-S281/CT-P29x series n=1, 49 CT-S300/CT-S310/CT-S2000/CT-S4000/ CT-S801(II)/CT-S851(II)/CT-S601(II)/CT-S651(II) CT-S310II/CT-S251/CT-D150/CT-E351/CT-D151/CT-E651 1≤n≤2, 49≤n≤50...
Page 146 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 • Paper Sensor status (n=1, 49) Status Hex. Decimal Paper found by Paper Near-end Sensor 0, 1 Paper not found by Paper Near-end Sensor...
Page 147: Paper Detecting Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.8 Paper Detecting Commands ESC c 3 n [Function] Selecting the Paper Sensor valid for a Paper-end signal output [Code] <1B>H<63>H<33>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 148: Esc C 4 N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC c 4 n [Function] Selecting the Paper Near-end Sensor valid for print stop [Code] <1B>H<63>H<34>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 149: Panel Switch Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.9 Panel Switch Commands ESC c 5 n [Function] Enabling/disabling the panel switches [Code] <1B>H<63>H<35>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 150: Macro Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.10 Macro Commands GS : [Function] Starting/ending macro definition [Code] <1D>H<3A>H [Outline] [The specification which is common to the model] • Specifying starting/ending macro definition.
Page 151: Gs ^ N1 N2 N3
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ^ n1 n2 n3 [Function] Executing the macro [Code] <1D>H<5E>H<n1><n2><n3> [Range] 0≤n1≤255 0≤n2≤255 0≤n3≤1 [Outline] [The specification which is common to the model] •...
Page 152: Cutter Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.11 Cutter Commands ESC i [Function] Full cutting of paper [Code] <1B>H<69>H [Outline] [The specification which is common to the model] • Executes full cutting of paper.
Page 153: Esc M
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC m [Function] Partial cutting of paper [Code] <1B>H<6D>H [Outline] [The specification which is common to the model] • Executes partial cutting of paper.
Page 154: Gs V M
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS V m --- (1) GS V m n --- (2) [Function] Cutting the paper [Code] (1)<1D>H<56>H<m> (2)<1D>H<56>H<m><n> [Range] (1)0≤m≤1, 48≤m≤49 (2)m=65, 66 0≤n≤255...
Page 155: Bar Code Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.12 Bar Code Commands GS H n [Function] Selecting of printing position of HRI characters [Code] <1D>H<48>H<n> [Range] 0≤n≤3, 48≤n≤51 [Outline] [The specification which is common to the model] •...
Page 156: Gs F N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS f n [Function] Selecting the font of HRI characters [Code] <1D>H<66>H<n> [Range] 0≤n≤2, 48≤n≤50 [Outline] [The specification which is common to the model] •...
Page 157: Gs H N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS h n [Function] Specifying the height of the bar code [Code] <1D>H<68>H<n> [Range] 1≤n≤255 [Outline] [The specification which is common to the model] •...
Page 158: Gs K M [D1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 (1)GS k m [d1...dk] NUL (2)GS k m n [d1...dn] [Function] Printing the bar code [Code] (1)<1D>H<6B>H<m> [d1…dk] NULL (2)<1D>H<6B>H<m><n> [d1…dn] [Range] (1)0≤m≤6 The definitions of “k” and “d” vary with the bar code system.
Page 159 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Caution] For (1): • This command ends with a NULL code. • For UPC-A or UPC-E, the bar code is printed when 12 bytes of bar code data have been entered, and the subsequent data is handled as normal data.
Page 160 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Description of Bar Codes] UPC-A This bar code, consisting of numerals only, has a fixed length of 12 columns; a 11- column number entered from the host or application software plus a check digit (12th column) automatically calculated inside the printer.
Page 161 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CODE93 This bar code, consisting of alphanumeric and control characters, has a variable length of columns. The HRI character string is preceded and followed by a “￭” character. HRI characters for control characters (00H - 1FH, and 7FH) are each printed as a combination of a “￭”...
Page 162 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CODE128 This bar code consists of 103 bar code characters and three code sets, enabling 128 ASCII code characters to be printed. It has a variable length of columns.
Page 163 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS1 DataBar Omnidirectional This bar code, consisting of numerals only, has a fixed length of 13 columns. The minimum height of the bar is 33 times of module size..
Page 164: Gs W N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS w n [Function] Specifying the horizontal size (magnification) of bar code [Code] <1D>H<77>H<n> [Range] 2≤n≤6 [Outline] [The specification which is common to the model] •...
Page 165: Commands For Non-Volatile Memory
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.13 Commands for Non-volatile Memory GS ( L pL pH m fn [parameter] GS 8 L p1 p2 p3 p4 m fn [parameter] [Function]...
Page 166 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D151/CT-E651 Code Function No. Function Sends NV graphics memory 0, 48 GS ( L pL pH m fn Function48 capacity. Prints graphics data stored in print...
Page 167: Fn=0, 48: Function 48 Sending Nv Graphics Memory Capacity
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=0, 48: Function 48 Sending NV Graphics Memory Capacity GS ( L pL pH m fn [Code] <1D>H<28>H<4C>H<pL><pH><m><fn> [Range] (pL+pH×256)=2 (pL=2, pH=0) m=48 fn=0, 48...
Page 168: Fn=3, 51: Function 51 Sending The Remaining Amount Of Nv Graphics Memory
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=3, 51: Function 51 Sending the Remaining Amount of NV Graphics Memory GS ( L pL pH m fn [Code] <1D>H<28>H<4C>H<pL><pH><m><fn> [Range] (pL+pH×256)=2 (pL=2, pH=0)
Page 169: Fn=64: Function 64 Sending Key Code List Of Defined Nv Graphics
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=64: Function 64 Sending Key Code List of Defined NV Graphics GS ( L pL pH m fn d1 d2 [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><d1><d2> [Range] (pL+pH×256)=4 (pL=4, pH=0)
Page 170: Fn=65: Function 65 Erasing All Data Of Nv Graphics In A Lump
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=65: Function 65 Erasing All Data of NV Graphics in a Lump GS ( L pL pH m fn d1 d2 d3 [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><d1><d2><d3>...
Page 171: Fn=67: Function 67 Defining Raster Type Graphics Data To Nv Memory
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=67: Function 67 Defining Raster Type Graphics Data to NV Memory GS ( L pL pH m fn a kc1 kc2 b xL xH yL yH [c d1...dk] 1...
Page 172: Fn=69: Function 69 Printing Specified Graphics
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=69: Function 69 Printing Specified Graphics GS ( L pL pH m fn kc1 kc2 x y [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><kc1><kc2><x><y> [Range] (pL+pH×256)=6 (pL=6, pH=0) m=48 fn=69 32≤kc1≤126...
Page 173: Fn=80: Function 80 Sending Key Code List Of Defined Download Graphics
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=80: Function 80 Sending Key Code List of Defined Download Graphics GS ( L pL pH m fn d1 d2 [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><d1><d2> （pL＋pH×256)＝4 (pL＝4、pH＝0) [Range] m＝48...
Page 174: Fn=81: Function 81 Erasing All Data Of Download Graphics In A Lump
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=81: Function 81 Erasing All Data of Download Graphics in a Lump GS ( L pL pH m fn d1 d2 d3 [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><d1><d2><d3>...
Page 175: Fn=85: Funciton 85 Printing Specified Download Grahics Data
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=85: Funciton 85 Printing Specified Download Grahics Data GS ( L pL pH m fn kc1 kc2 <1D>H<28>H<4C>H<pL><pH><m><fn><kc1><kc2><x><y> [Code] [Range] (pL＋pH×256)＝6 (pL＝6、pH＝0) m＝48 fn＝85 32≦kc1≦126...
Page 176: Fn=112: Function 112 Storing Raster Type Graphics Data To Print Buffer
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=112: Function 112 Storing Raster Type Graphics Data to Print Buffer GS ( L pL pH m fn a bx by c xL xH yL yH d1...dk [Code] <1D>H<28>H<4C>H<pL><pH><m><fn><a><bx><by><c><xL><xH><yL><yH>...
Page 177: Gs D M Fn A Kc1 Kc2 B C D1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS D m fn a kc1 kc2 b c d1…dk [Function] Defining Windows Bitmap to NV Memory [Code] <1D>H<44>H<m><fn><a><kc1><skc2><b><c><d1>...<dk> [Range] [機種依存仕様] CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D151/CT-E651 fn＝67、83 [Outline] [The specification which is common to the model] •...
Page 178: Fn=67: Function 67 Defining Windows Bitmap To Nv Memory
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=67: Function 67 Defining Windows Bitmap to NV Memory GS D m fn a kc1 kc2 b c d1…dk [Code] <1D>H<44>H<m><fn><a><kc1>H<kc2><b><c><d1>...<dk> [Range] m=48 fn=67 a=48 32≦kc1≦126、32≦kc2≦126...
Page 179: Fn=83: Function 83 Defining Windows Bitmap To Download Memory
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=83: Function 83 Defining Windows Bitmap to Download Memory GS D m fn a kc1 kc2 b c d1…dk [Code] <1D>H<44>H<m><fn><a><kc1>H<kc2><b><c><d1>...<dk> [Rnage] m=48 fn=67 a=48 32≦kc1≦126、32≦kc2≦126...
Page 180: Fs P N M
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS p n m [Function] Printing the download NV bit images [Code] <1C>H<70>H<n><m> [Range] 1≤n≤255, 0≤m≤3, 48≤m≤51 [Outline] [The specification which is common to the model] •...
Page 181: Fs Q N [Xl Xh Yl Yh D1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS q n [xL xH yL yH d1...dk] 1... [xL xH yL yH d1...dk] n [Function] Defining the download NV bit image [Code] <1C>H<71>H<n> [<xL><xH><yL><yH><d1…dk>] 1… [<xL><xH><yL><yH><d1…dk>] n [Range] 1≤n≤255, 0≤xL≤255...
Page 182 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 • The definition data of one NV bit image consists of [xL xH yL yH d1… dk] . Therefore, when only one NV bit image is defined, n = 1;...
Page 183: Kanji Control Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.14 Kanji Control Commands FS ! n [Function] Collectively setting Kanji print mode [Code] <1C>H<21>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 184 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS & [Function] Setting Kanji mode [Code] <1C>H<26>H [Outline] [The specification which is common to the model] • Sets Kanji mode. Japanese Kanji specifications: This command is invalid when Kanji code system is Shift JIS.
Page 185: Fs - N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS - n [Function] Setting/canceling Kanji underline [Code] <1C>H<2D>H<n> [Range] 0≤n≤2, 48≤n≤50 [Outline] [The specification which is common to the model] • Sets or cancels Kanji underline.
Page 186 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS . [Function] Canceling Kanji mode [Code] <1C>H<2E>H [Outline] [The specification which is common to the model] • Cancels Kanji mode. Japanese Kanji specifications: This command is invalid when Kanji code system is Shift JIS.
Page 187: Fs 2 A1 A2 [D] K
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS 2 a1 a2 [d] k [Function] Defining external character [Code] <1C>H<32>H<a1>H<a2>H [<d>] k [Range] Japanese Kanji specifications: • In case of JIS code system a1=<77>H, <21>H≤a2≤<7E>H...
Page 188 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 When UTF-8 is selected (FS C n and n=8） • This command is ignored. • External character defined before choosing UTF-8 is not printed on UTF-8 mode.
Page 189: Fs C N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS C n [Function] Selecting Kanji code system [Code] <1C>H<43>H<n> [Range] 0≤n≤1, 48≤n≤49 [Outline] [The specification which is common to the model] • Selects Kanji code system.
Page 190 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Caution] [The specification which is common to the model] • Kanji code valid in JIS code system is 21H to 7EH for both 1st and 2nd bytes.
Page 191 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 LPRINT CHR$(&H8A); CHR$(&HBF); LPRINT CHR$(&H8E); CHR$(&H9A); LPRINT CHR$(&HA); LPRINT CHR$(&H1C);"."; - 190 -...
Page 192: Fs S N1 N2
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS S n1 n2 [Function] Setting Kanji space amount [Code] <1C>H<53>H<n1><n2> [Range] 0≤n1≤255 0≤n2≤255 [Outline] [The specification which is common to the model] • Sets both right and left space amount of Kanji in units of dot.
Page 193: Fs W N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS W n [Function] Setting/canceling four times enlargement of Kanji [Code] <1C>H<57>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • Sets or cancels four times enlargement of Kanji.
Page 194: Fn=48: Function 48 Set Kanji Fonts
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS ( A pL pH fn […] [Function] Setting font attribute of Kanji [Outline] Setting Kanji font attribute means execution of processing for Kanji font attribute by the value of “fn” specified.
Page 195: Black Mark Control Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.15 Black Mark Control Commands GS FF [Function] Printing and ejecting Black mark paper/ label paper [Code] <1D>H<0C>H [Outline] [The specification which is common to the model] •...
Page 196 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 •When MSW4-5=OFF (Black mark), printer feed the paper backward by about 5mm. •When MSW4-5=ON (Label paper) if the distance between black mark or label length is less than 30mm, next or second next black mark/label will be ejected and then feed paper until detecting the black mark or top of label.
Page 197 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS < [Function] Initializing the printer mechanism [Code] <1D>H<3C>H [Outline] [The specification which is common to the model] • Performs initializing operation at Black mark/ label similar to the initialization at power on.
Page 198: Gs A M N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS A m n [Function] Correcting the leader position of Black mark paper/ label paper [Code] <1D>H<41>H<m><n> [Range] 0≤m≤255 0≤n≤255 [Outline] [The specification which is common to the model] •...
Page 199: Gs C 0 M N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS C 0 m n [Function] Setting the numbering print mode [Code] <1D>H<43>H<30>H<m><n> [Range] 0≤m≤5 0≤n≤2 [Outline] [The specification which is common to the model] •...
Page 200: Gs C 1 N1 N2 N3 N4 N5 N6
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS C 1 n1 n2 n3 n4 n5 n6 [Function] Setting the numbering counter mode (A) [Code] <1D>H<43>H<31>H<n1><n2><n3><n4><n5><n6> [Range] 0≤n1, n2, n3, n4, n5, n6≤255...
Page 201: Gs C 2 N1 N2
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS C 2 n1 n2 [Function] Setting the numbering counter [Code] <1D>H<43>H<32>H<n1><n2> [Range] 0≤n1≤255 0≤n2≤255 [Outline] [The specification which is common to the model] •...
Page 202: Gs C ; N1 ; N2 ; N3 ; N4 ; N5
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS C ; n1 ; n2 ; n3 ; n4 ; n5 ; [Function] Setting the numbering counter mode (B) [Code] <1D>H<43>H<3B>H<n1><3B>H<n2><3B>H<n3><3B>H<n4><3B>H<n5><3B>H <n1>, <n2>, <n3>, <n4>, <n5> are character codes.
Page 203: Gs C
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS c [Function] Print the counter [Code] <1D>H<63>H [Outline] [The specification which is common to the model] • This command prints the serial number counter data.
Page 204: Gs L N1L N1H N2L N2H
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS l n1L n1H n2L n2H [Function] Setting the Black mark/ label length [Code] <1D>H<6C>H<n1L><n1H><n2L><n2H> [Range] 0≤n1L≤255 (24≤n1L+n1H×256≤360) 0≤n1H≤1 8≤n2L≤30 n2H=0 [Outline] [The specification which is common to the model] •...
Page 205: Gs P N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS p n [Function] Changing paper type [Code] <1D>H <70>H <n> [Range] 0≤n≤255 specify receipt paper specify label paper specify black mark paper [Outline] [The specification which is common to the model] •...
Page 206: Fs Ff
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 FS FF Printing and feeding black marl/label paper to manual cut position [Function] [Code] <1C>H <0C>H [Outline] [The specification which is common to the model] 1.
Page 207: Printer Function Setting Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.16 Printer Function Setting Commands GS ( E pL pH fn […] [Function] Printer function setting command [Outline] [The specification which is common to the model] •...
Page 208: Fn=1: Function 1 Transferring To Printer Function Setting Mode
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=1: Function 1 Transferring to Printer Function Setting Mode GS ( E pL pH fn d1 d2 [Code] <1D>H<28>H<45>H <pL><pH><fn><d1><d2> [Range] (pL+pH×256)=3 (pL=3, pH=0) fn=1 d1=73 (“I”)
Page 209: Fn=3: Function 3 Setting Memory Switch Value
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=3: Function 3 Setting Memory Switch Value GS ( E pL pH fn [a1 b18...b11] ... [ak bk8...bk1] [Code] <1D>H<28>H<45>H<pL><pH><fn> [<a1><b18>…<b11>] … [<ak><bk8>…<bk1>] [Range] 10≤(pL+pH×256)≤65535...
Page 210 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • Setting MSW 1 (a=1) • Setting MSW 3 (a=3) b (Set Value) Function b (Set Value) Function 48 (Default) Reports the power on.
Page 211 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • Setting MSW 1 (a=1) • Setting MSW 3 (a=3) b (Set Value) Function b (Set Value) Function 48 (Default) Reports the power on.
Page 212 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • Setting MSW 4 (a=4) • Setting MSW 5 (a=5) b (Set Value) Function b (Set Value) Function At the selection of Black mark/Label paper, enables auto...
Page 213 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300 48(Default) Reserved 48(Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on. Does not report power on.
Page 214 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300 • Setting MSW 4 (a=4) b (Set Value) Function At the selection of Black mark paper, disables auto 48 (Default) end-measurement. At the selection of Black mark paper, enables auto end-measurement.
Page 215 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310 48 (Default) Enables PNE. Disables PNE. • Setting MSW 1 (a=1) b (Set Value) Function • Setting MSW 3 (a=3) 48 (Default) Reports the power on.
Page 216 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310 • Setting MSW 4 (a=4) b (Set Value) Function At the selection of Black mark paper, disables auto 48 (Default) end-measurement. At the selection of Black mark paper, enables auto end-measurement.
Page 217 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 218 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 219 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 48 (Default) Enables PNE. Disables PNE. • Setting MSW 1 (a=1) b (Set Value) Function • Setting MSW 3 (a=3) 48 (Default) Reports the power on.
Page 220 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • Setting MSW 4 (a=4) (Black mark/Label model) • Setting MSW 5 (a=5) b (Set Value) Function b (Set Value) Function At the selection of Black mark/Label paper, enables auto 48 (Default) Buzzer sound enabled.
Page 221 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • Setting MSW 1 (a=1) • Setting MSW 3 (a=3) b (Set Value) Function b (Set Value) Function 48 (Default) Reports the power on.
Page 222 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • Setting MSW 4 (a=4) • Setting MSW 5 (a=5) b (Set Value) Function b (Set Value) Function At the selection of Black mark paper/ label paper, enables 48 (Default) Buzzer sound enabled.
Page 223 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851/CT-S601/CT-S651 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 224 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851/CT-S601/CT-S601 • Setting MSW 4 (a=4) • Setting MSW 5 (a=5) b (Set Value) Function b (Set Value) Function At the selection of Black mark/Label paper, disables auto 48 (Default) Buzzer sound enabled.
Page 225 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801II/CT-S851II/CT-S601II/CT-S651II 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 226 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801II/CT-S851II/CT-S601II/CT-S651II • Setting MSW 4 (a=4) • Setting MSW 5 (a=5) b (Set Value) Function b (Set Value) Function At the selection of Black mark/Label paper, disables auto 48 (Default) Buzzer sound enabled.
Page 227 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 228 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 229 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series 49 (Default) Disables PNE. • Setting MSW 1 (a=1) • Setting MSW 3 (a=3) b (Set Value) Function 48 (Default) Reports the power on.
Page 230 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • Setting MSW 4 (a=4) b (Set Value) Function Reserved Reserved Reserved 49 (Default) Reserved Paper heading cut disabled. Paper heading cut enabled.
Page 231 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 232 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 233 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 48 (Default) Reserved 48 (Default) Enables PNE. • Setting MSW 1 (a=1) Disables PNE. b (Set Value) Function 48 (Default) Reports the power on.
Page 234 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 235 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 48 (Default) Enables PNE. Disables PNE. • Setting MSW 1 (a=1) b (Set Value) Function • Setting MSW 3 (a=3) 48 (Default) Reports the power on.
Page 236 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 237 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 48 (Default) Enables PNE. Disables PNE. • Setting MSW 1 (a=1) b (Set Value) Function • Setting MSW 3 (a=3) 48 (Default) Reports the power on.
Page 238 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • Setting MSW 5 (a=5) b (Set Value) Function 48 (Default) Buzzer sound enabled. Buzzer sound disabled. 48 (Default) Basic calculation pitch (180 dpi / 360 dpi).
Page 239: Fn=4: Function 4 Sending The Set Memory Switch Value
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=4: Function 4 Sending the Set Memory Switch Value GS ( E pL pH fn a [Code] <1D>H<28>H<45>H<pL><pH><fn><a> [Range] (pL+pH×256)=2 fn=4 CT-S280 a=1, 2, 3...
Page 240: Fn=5: Function 5 Setting Customized Value
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=5: Function 5 Setting Customized Value GS ( E pL pH fn [a1 n1L n1H] ... [ak nkL nkH] [Code] <1D>H<28>H<45>H<pL><pH><fn> [<a1><n1L><n1H>] … [<ak><nkL><nkH>] [Range] 4≤(pL+pH×256)≤65535...
Page 241 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Outline] [The specification which is common to the model] • Sets the customized value set in “a” to (nL+nH×256). Function Specifies user NV memory capacity.
Page 242 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 Selects the emulation for old dot impact printer Selects the liner free mode setting [Caution] [The specification which is common to the model] • This function operates only in printer function setting mode.
Page 243 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • a=5: Sets printing density to the level specified by (nL+nH×256). • a=116: Sets the paper specified by (nL+nH×256). (nL+nH×256) Printing Density (nL+nH×256)
Page 244 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • a=214: Select the enable/disable of Kanji specified by (nL+nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL+nH×256) Kanji (nL＋nH×256) (nL＋nH×256)
Page 245 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • a=5: Sets printing density to the level specified by (nL+nH×256). • a=116: Sets the paper specified by (nL+nH×256). (nL+nH×256) Printing Density (nL+nH×256)
Page 246 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • a=213: Selects the flow control specified by (nL+nH×256) when virtual • a=218: Select the codepage specified by (nL+nH×256) COM is set. Codepage Codepage (nL＋nH×256)
Page 247 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300 • a=3: Sets paper width to the size specified by (nL+nH×256). • a=6: Sets printing speed to the value specified by (nL+nH×256). (nL+nH×256) Paper Width (nL+nH×256)
Page 248 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300 • a=202: Controls input buffer full Busy with the value selected by • a=222: Head margin set by the value selected by (nL+nH×256).
Page 249 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310 • a=3: Sets paper width to the size specified by (nL+nH×256). • a=97: Sets the number of divisions for conducting head specified by (nL+nH×256).
Page 250 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310 • a=202: Controls input buffer full Busy with the value selected by • a=222: Head margin set by the value selected by (nL+nH×256).
Page 251 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 252 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • a=202: Controls input buffer full Busy with the value selected by • a=214: Select the enable/disable of Kanji specified by (nL+nH×256) (nL+nH×256) and controls Busy with output/cancel timing (remaining capacity).
Page 253 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II ・a=245: Selects the line gap reduction ratio specified by (nL＋nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL＋nH×256) (nL＋nH×256) 1(Default)
Page 254 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II ・a=247: Select the number of dot for auto side shift specified by • a=251: Selects the liner free mode setting specified by (nL+nH×256).
Page 255 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=1: Sets the user NV memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 256 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=116: Sets the paper specified by (nL+nH×256). • a=212: Selects DMA (Direct Memory Access) control of serial communication specified by (nL+nH×256). (nL+nH×256)
Page 257 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=221: Sets the maximum length of black mark page with the value • a=225: Sets head distance with the value selected by (nL+nH×256).
Page 258 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • a=1: Sets the user NV memory capacity to the size specified by • a=3: Sets paper width to the size specified by (nL+nH×256).
Page 259 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • a=6: Sets printing speed to the value specified by (nL+nH×256). • a=202: Controls input buffer full Busy with the value selected by (nL+nH×256) and controls Busy with output/cancel timing...
Page 260 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • a=214: Select the enable/disable of Kanji specified by (nL+nH×256). (nL+nH×256) Kanji Invalid(OFF) 2(Default) Valid(ON) - 259 -...
Page 261 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 262 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=116: Sets the paper specified by (nL+nH×256). • a=201: Outputs ACK to the position specified by (nL+nH×256). (nL+nH×256) Paper (nL+nH×256) ACK Output Position 1(Default) Specified single color paper.
Page 263 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=213: Selects the flow control specified by (nL+nH×256) when virtual • a=218: Select the codepage specified by (nL+nH×256) COM is set. Codepage Codepage (nL＋nH×256)
Page 264 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=222: Sets Sensor and distance between header with the value selected • a=227: Sets max length of auto length measurement with the value by (nL+nH×256).
Page 265 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851(II) • a=234: Selects the direction of LCD message specified by (nL+nH×256) • a=230: Sets the language of LCD messages selected by (nL+nH×256). (nL＋nH×256) Language (nL＋nH×256)
Page 266 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=238: Sets label bottom margin with the value selected by (nL+nH×256). • a=242: Sets the max dot number with Powered USB specified by [CT-S801(II), CT-S851] (nL+nH×256)
Page 267 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=245: Selects the line gap reduction ratio specified by (nL+nH×256). • a=247: Selects the number of dot for auto side slide specified by (nL+nH×256).
Page 268 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=251: Selects the liner free mode setting specified by (nL+nH×256). (nL+nH×256) Printing Density 1(Default) Invalid - 267 -...
Page 269 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601(II)/CT-S651(II) • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 270 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601(II)/CT-S651(II) • a=116: Sets the paper specified by (nL+nH×256). • a=201: Outputs ACK to the position specified by (nL+nH×256). (nL+nH×256) Paper (nL+nH×256) ACK Output Position 1(Default) Specified single color paper.
Page 271 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601(II)/CT-S651(II) • a=213: Selects the flow control specified by (nL+nH×256) when virtual • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage COM is set.
Page 272 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601（II）/CT-S651(II) • a=242: Sets the max dot number with Powered USB specified by (nL+nH×256) • a=245: Selects the line gap reduction ratio specified by (nL＋nH×256) (nL＋nH×256)
Page 273 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601（II）/CT-S651(II) • a=247: Selects the number of dot for auto side slide specified by • a=251: Selects the liner free mode setting specified by (nL+nH×256).
Page 274 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 275 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=202: Controls input buffer full Busy with the value selected by • a=138: Sets bezel LED specified Lighting Mode by (nL+nH×256). (nL+nH×256) and controls Busy with output/cancel timing (remaining capacity).
Page 276 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=214: Select the enable/disable of Kanji specified by (nL+nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL+nH×256) Kanji (nL＋nH×256) (nL＋nH×256)
Page 277 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=244: Selects the top margin specified by (nL＋nH×256). • a=247: Selects the number of dot for auto side slide specified by (nL+nH×256).
Page 278 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=249: Selects the old command specified by (nL+nH×256). (nL＋nH×256) Old Command Invalid 1(Default) CBM1 CBM2 • a=251: Selects the liner free mode setting specified by (nL+nH×256).
Page 279 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • a=5: Sets printing density to the level specified by (nL+nH×256). • a=213: Selects the flow control specified by (nL+nH×256) when virtual COM is set.
Page 280 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL＋nH×256) (nL＋nH×256) Codepage PC437 Codepage PC866 Katakana Codepage PC857 Codepage PC850 WPC1252...
Page 281 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 282 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • a=202: Controls input buffer full Busy with the value selected by • a=216: Select the JIS/Shift JIS specified by (nL+nH×256) (nL+nH×256) and controls Busy with output/cancel timing (remaining capacity).
Page 283 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ・a=244: Selects the top margin specified by (nL＋nH×256) CT-D150 • a=218: Select the codepage specified by (nL+nH×256) (Small top margin = long back feed at printing start）...
Page 284 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 ・a =246: Selects the mode to print compressed character specified by ・a=248： Selects the event for the buzzer activation specified by (nL＋nH×256) (nL＋nH×256)
Page 285 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 286 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • a=202: Controls input buffer full Busy with the value selected by • a=216: Select the JIS/Shift JIS specified by (nL+nH×256) (nL+nH×256) and controls Busy with output/cancel timing (remaining capacity).
Page 287 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 ・a=245: Selects the line gap reduction ratio specified by (nL＋nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL＋nH×256) (nL＋nH×256) 1(Default)
Page 288 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 ・a=247: Select the number of dot for auto side shift specified by • a=251: Selects the liner free mode setting specified by (nL+nH×256).
Page 289 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 290 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=202: Controls input buffer full Busy with the value selected by • a＝151: Sets the Bluetooth Security/Connect Device specified (nL+nH×256) and controls Busy with output/cancel timing by (nL+nH×256).
Page 291 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=216: Select the JIS/Shift JIS specified by (nL+nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL＋nH×256) (nL＋nH×256) 1(Default) Codepage PC437 WPC1252 (nL+nH×256)
Page 292 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 ・a=244: Selects the top margin specified by (nL＋nH×256) ・a =246: Selects the mode to print compressed character specified by (Small top margin = long back feed at printing start）...
Page 293 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 ・a=248： Selects the event for the buzzer activation specified by (nL＋nH×256) Buzzer enent (nL+nH×256) All events / errors (Default) Except cover open Except cover open / no paper •...
Page 294 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=2: Sets NV graphic memory capacity to the size specified by • a=5: Sets printing density to the level specified by (nL+nH×256).
Page 295 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=202: Controls input buffer full Busy with the value selected by • a＝151: Sets the Bluetooth Security/Connect Device specified (nL+nH×256) and controls Busy with output/cancel timing by (nL+nH×256).
Page 296 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=216: Select the JIS/Shift JIS specified by (nL+nH×256) • a=218: Select the codepage specified by (nL+nH×256) Codepage Codepage (nL+nH×256) JIS/Shift JIS (nL＋nH×256) (nL＋nH×256)
Page 297 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 ・a=244: Selects the top margin specified by (nL＋nH×256) ・a =246: Selects the mode to print compressed character specified by (Small top margin = long back feed at printing start）...
Page 298 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 ・a=248： Selects the event for the buzzer activation specified by (nL＋nH×256) Buzzer enent (nL+nH×256) All events / errors (Default) Except cover open Except cover open / no paper •...
Page 299: Fn=6: Function 6 Sending The Set Customized Value
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=6: Function 6 Sending the Set Customized Value GS ( E pL pH fn a [Code] <1D>H<28>H<45>H<pL><pH><fn><a> [Range] (pL+pH×256)=2 (pL=2, pH=0) fn=6 CT-S280 a=5, 6, 116, 201, 202, 214, 216, 217, 218...
Page 300 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Outline] [The specification which is common to the model] • Sends the set value of customized value set by “a”. Hex. No. of Data...
Page 301 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 50(“2”) 52(“4”) 48(“0”) 50(“2”) 52(“4”) 49(“1”) 50(“2”) 52(“4”) 50(“2”) 50(“2”) 52(“4”) 51(“3”) 50(“2”) 52(“4”) 52(“4”) 50(“2”) 52(“4”) 53(“5”) 50(“2”) 52(“4”) 54(“6”) 50(“2”) 52(“4”) 55(“7”) 50(“2”)
Page 302 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • a=5: When print density is specified • a=116: When kind of paper is specified Setting Status Sending Data Setting Status Sending Data...
Page 303 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • a=216: When JIS/Shift JIS is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 304 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • a=116: When kind of paper is specified Setting Status Sending Data • a=5: When print density is specified Stored Setting Status Sending Data...
Page 305 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • a=214: When Kanji is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored Codepage...
Page 306 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300/CT-S310 • a=3: When paper width is specified • a=6: When printing speed is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 307 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300/CT-S310 • a=201: When ACK output position is specified • a=222: When head margin is specified Setting Status Sending Data Setting Status Sending Data...
Page 308 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 309 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • a=202: Input buffer full Busy output/cancel timing •a=216: When JIS/Shift JIS is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 310 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II ・a=245: When Line Gap Reduce n is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 311 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II ・a=247: When Auto Side Shift is specified • a=251:When liner free mode is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 312 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=1: When user NV memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 313 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=116: When kind of paper is specified • a=213: When the flow control of virtual COM is specified. Setting Status Sending Data...
Page 314 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • a=222: When head margin is specified • a=225: When head distance is specified Setting Status Sending Data Setting Status Sending Data Head...
Page 315 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • a=1: When user NV memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 316 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • a=116: When kind of paper is specified • a=213: When the flow control of virtual COM is specified. Setting Status Sending Data...
Page 317 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 318 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851 • a=116: When kind of paper is specified • a=201: When ACK output position is specified Setting Status Sending Data Setting Status Sending Data...
Page 319 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=216: When Kanji Code is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 320 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=221: When black mark page length is specified. [CT-S801(II), CT-S851] • a=224: When head margin is specified. [CT-S801(II), CT-S851] Setting Status Sending Data...
Page 321 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=228: When after an auto cut movement is specified. [CT-S801II] • a=231: When LCD download character is specified Setting Status Sending Data...
Page 322 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=235: When distance between labels is specified. [CT-S801(II), CT-S851] • a=238: When label bottom margin is specified. [CT-S801(II), CT-S851] Setting Status Sending Data...
Page 323 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=241: When max dot number in 1 head division is specified • a=245: When Line Gap Reduce n is specified Setting Status...
Page 324 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801(II)/CT-S851(II) • a=246: When Line Gap Reducen is specified. [CT-S801II, CT-S851II] • a=248: When the event for the buzzer activation is specified. [CT-S801II, CT-S851II]...
Page 325 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601(II)/CT-S651(II) • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 326 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601（II）/CT-S651(II) • a=116: When kind of paper is specified • a=201: When ACK output position is specified Setting Status Sending Data Setting Status Sending Data...
Page 327 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601(II)/CT-S651(II) • a=216: When Kanji Code is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 328 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601（II）/CT-S651(II) ・a=244: When Top Margin is specified • a=240:When buzzer sound is specified Setting Status Sending Data Setting Status Sending Data Stored Stored Buzzer Sound...
Page 329 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S601（II）/CT-S651(II) • a=246: When Line Gap Reduce n is specified. [CT-S601II, CT-S651II] • a=248: When the event for the buzzer activation is specified. [CT-S601II, CT-S651II]...
Page 330 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 331 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=138: When Lighting Mode is specified • a=202: Input buffer full Busy output/cancel timing Setting Status Sending Data Setting Status Sending Data...
Page 332 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=216: When Kanji Code is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 333 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=244: When Top Margin is specified • a=246: When Line Gap Reducen is specified Setting Status Sending Data Setting Status Sending Data...
Page 334 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • a=248: When the event for the buzzer activation is specified Setting Status Sending Data Stored Buzzer event 1st Byte 2nd Byte 3rd Byte...
Page 335 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • a=5: When print density is specified • a=213: When the flow control of virtual COM is specified. Setting Status Sending Data...
Page 336 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • a=217: When international character set is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data...
Page 337 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 338 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • a=202: Input buffer full Busy output/cancel timing • a=216: When JIS/Shift JIS is specified Setting Status Sending Data Setting Status Sending Data...
Page 339 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ・a=244: When Top Margin is specified CT-D150 Setting Status Sending Data • a=218: When codepage is specified Stored Setting Status Sending Data Codepage 1st Byte...
Page 340 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 ・a=247: When Auto Side Shift is specified • a=251:When liner free mode is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 341 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 342 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • a=202: Input buffer full Busy output/cancel timing • a=216: When JIS/Shift JIS is specified Setting Status Sending Data Setting Status Sending Data...
Page 343 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ・a=244: When Top Margin is specified CT-E351 Setting Status Sending Data • a=218: When codepage is specified Stored Setting Status Sending Data Codepage 1st Byte...
Page 344 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 ・a=247: When Auto Side Shift is specified • a=251:When liner free mode is specified Setting Status Sending Data Setting Status Sending Data Stored...
Page 345 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 346 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a＝151: When Bluetooth Security/Connect Device is specified • a=212: When DMA (Direct Memory Access) control of serial communication is specified Setting Status...
Page 347 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=216: When Kanji Code is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 348 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=244: When Top Margin is specified • a=246: When Line Gap Reducen is specified Setting Status Sending Data Setting Status Sending Data...
Page 349 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • a=247: When dot for auto side slide is specified • a=251:When liner free mode is specified Setting Status Sending Data Setting Status...
Page 350 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=2: When NV graphics memory capacity is specified • a=5: When print density is specified Setting Status Sending Data Setting Status Sending Data...
Page 351 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a＝151: When Bluetooth Security/Connect Device is specified • a=212: When DMA (Direct Memory Access) control of serial communication is specified Setting Status...
Page 352 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=216: When Kanji Code is specified • a=218: When codepage is specified Setting Status Sending Data Setting Status Sending Data Stored Stored...
Page 353 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=244: When Top Margin is specified • a=246: When Line Gap Reducen is specified Setting Status Sending Data Setting Status Sending Data...
Page 354 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • a=247: When dot for auto side slide is specified • a=251:When liner free mode is specified Setting Status Sending Data Setting Status...
Page 355: Fn=7: Function 7 Copying User-Defined Page
Font Type Font B: 9 (horizontal)×17 (vertical) Font A: 12 (horizontal)×24 (vertical) Font C: 8 (horizontal)×16 (vertical) CT-S280/CT-S281/CT-S2000/CT-S4000/CT-S310II/ CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D150/CT-E351/CT-D151/ CT-E651 Font Type Font B: 9 (horizontal)×24 (vertical) Font A: 12 (horizontal)×24 (vertical) Font C: 8 (horizontal)×16 (vertical) - 354 -...
Page 356: Fn=8: Function 8 Defining Data By The Column Format To Character Code Page Of Work Area
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=8: Function 8 Defining Data by the Column Format to Character Code Page of Work Area GS ( E pL pH fn y c1 c2 [xd1...d(y×x)] k [Code] <1D>H<28>H<45>H<pL><pH><fn><y><c1><c2>...
Page 357: Fn=9: Function 9 Defining Data In The Raster Format To The Character Code Page Of Work Area
CT-S300/CT-S310/CT-S801/CT-S851/CT-S601/CT-S651/CT-P29x series 0≤x≤17 (At selection of font B) CT-S280/CT-S281/CT-S2000/CT-S4000/ CT-S310II/ CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D150/CT-E351/CT-D151/ CT-E651 0≤x≤24 (At selection of font B) [Outline] [The specification which is common to the model] • Defines the data in raster format in units of character on the character code page in work area.
Page 358: Fn=10: Function 10 Erasing Data Of Character Code Page Data In Work Area
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=10: Function 10 Erasing Data of Character Code Page Data in Work Area GS ( E pL pH fn c1 c2 [Code] <1D>H<28>H<45>H<pL><pH><fn><c1><c2> [Range] (pL+pH×256)=3...
Page 359: Fn=11: Function 11 Setting Communication Conditions
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=11: Function 11 Setting Communication Conditions GS ( E pL pH fn a d1...dk [Code] <1D>H<28>H<45>H<pL><pH><fn><a><d1>...<dk> [Range] 3≤(pL+pH×256)≤65535(0≤pL≤255, 0≤pH≤255) fn=11 1≤a≤4 (Not changed in other than specified range) 48≤d≤57 (Not changed in other than specified range)
Page 360: Fn=12: Function 12 Sending The Set Communication Conditions
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=12: Function 12 Sending the Set Communication Conditions GS ( E pL pH fn a [Code] <1D>H<28>H<45>H<pL><pH><fn><a> [Range] (pL+pH×256)=2 (pL=2, pH=0) fn=12 1≤a≤4 (Does not send in other than specified range)
Page 361: Fn=101: Function 101 Changing Bluetooth Setting
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=101: Function 101 Changing Bluetooth setting GS ( E pL pH fn m <1D>H<28>H<45>H<pL><pH><fn><a><d1>...<dk> [Code] 2≤(pL+pH×256) ≤66 [Range] fn=101 1≤a≤6, 8 (CT-S281BD: 1≤a≤8) ≠20H, 22H 20H≤d≤2BH, 2DH≤d≤7EH, d1...
Page 362: Fn=102: Function 102 Sending Setting Of Bluetooth
(iAP)Application ID • Initial Value Setting value Bluetooth address Last 4 digits out of 12 digits (colon excluded) Model name_xx (xx is last 2 digits of Bluetooth address) CITIZEN SYSTEMS (CT-S281BD) CITIZEN SYSTEMS Model name (Example: CT-S801II) com.citizen.protocol01 82KYFK9X2H Model name_xx (xx is last 2 digits of Bluetooth address)
Page 363: Fn=255: Function 255 Setting All Contents Set By Printer Function Setting Mode To The State At Shipment
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=255: Function 255 Setting All Contents Set by Printer Function Setting Mode to the State at Shipment GS ( E pL pH fn a [Code] <1D>H<28>H<45>H<pL><pH><fn><a>...
Page 364 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ( K pL pH fn m [Function] Selecting print control method [Outline] [The specification which is common to the model] Executes the setting related to the print control specified by the value of “fn”.
Page 365: Fn=49: Function 49 Setting Printing Density
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=49: Function 49 Setting Printing Density GS ( K pL pH fn m [Code] <1D>H<28>H<4B>H<pL><pH><fn><m> [Range] (pL+pH×256)=2 (pL=2, pH=0) fn=49 0≤m≤8, 250≤m≤255 [Default] m=0 (Customized value setting value)
Page 366: Fn=50: Function 50 Setting Printing Speed
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=50: Function 50 Setting Printing Speed GS ( K pL pH fn m [Code] <1D>H<28>H<4B>H<pL><pH><fn><m> [Range] (pL+pH×256)=2 (pL=2, pH=0) fn=50 0≤m≤9, 48≤m≤57 [Default] m=0 (Customized value setting)
Page 367: Fn=97: Function 97 Setting Number Of Divisions For Head Conducting
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=97: Function 97 Setting Number of Divisions for Head Conducting GS ( K pL pH fn m [Code] <1D>H<28>H<4B>H<pL><pH><fn><m> [Range] (pL+pH×256)=2 (pL=2, pH=0) fn=97...
Page 368: Fn=48: Function 48 Selects Character Color
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ( N pL pH fn m [Function] Designating font attribute [Outline] [The specification which is common to the model] • Executes processing of font attribute by the specified fn value.
Page 369: 2-Dimensional Code Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.17 2-dimensional code Commands GS ( k pL pH cn fn [parameter] [Function] Setting and printing 2-dimensional code [Outline] [The specification which is common to the model] •...
Page 370 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 Function Code Function GS ( k pL pH cn fn n Function367 Sets the module width of GS1 DataBar Sets the maximum width of...
Page 371: Fn=65: Function 65 Setting The Number Of Digits Of Pdf417
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=65: Function 65 Setting the number of digits of PDF417 GS ( k pL pH cn fn n [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><n> [Range] (pL+pH×256)=3 (pL=3, pH=0)
Page 372: Fn=67: Function 67 Setting Module Width Of Pdf417
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=67: Function 67 Setting module width of PDF417 GS ( k pL pH cn fn n [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><n> [Range] (pL+pH×256)=3 (pL=3, pH=0) cn=48 fn=67 2≤n≤8...
Page 373: Fn=69: Function 69 Setting Error Correction Level Of Pdf417
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=69: Function 69 Setting error correction level of PDF417 GS ( k pL pH cn fn m n [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><m><n> [Range] (pL+pH×256)=4 (pL=4, pH=0)
Page 374: Fn=70: Function 70 Setting Options For Pdf417
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=70: Function 70 Setting Options for PDF417 GS ( k pL pH cn fn m [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><m> [Range] (pL+pH×256)=3 (pL=3, pH=0) cn=48 fn=70 m=0, 1...
Page 375: Fn=81: Function 81 Printing 2D Code Data In 2D Code Data Storage Area
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=81: Function 81 Printing 2D code data in 2D code data storage area GS ( k pL pH cn fn m [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><m> [Range] (pL+pH×256)=3 (pL=3, pH=0)
Page 376: Fn=65: Function 165 Specifying Qrcode Model
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=65: Function 165 Specifying QRCode model GS ( k pL pH cn fn n1 n2 [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><n1><n2> [Range] (pL+pH×256)=4 (pL=4, pH=0) cn=49 fn=65 n1=49, 50...
Page 377: Fn=69: Function 169 Setting Qrcode Error Correction Level
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=69: Function 169 Setting QRCode error correction level GS ( k pL pH cn fn n [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><n> [Range] (pL+pH×256)=3 (pL=3, pH=0) cn=49 fn=69 48≤n≤51...
Page 378: Fn=81: Function 181 Printing 2D Code Data In 2D Code Data Storage Area
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=81: Function 181 Printing 2D code data in 2D code data storage area GS ( k pL pH cn fn m [Code] <1D>H<28>H<6B>H<pL><pH><cn><fn><m> [Range] (pL+pH×256)=3 (pL=3, pH=0)
Page 379: Fn=67: Function 367 Setting Module Width Of 2D Gs1 Databar
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=67: Function 367 Setting module width of 2D GS1 DataBar GS ( k pL pH cn fn n <1D>H<28>H<6B>H<pL><pH><cn><fn><n> [Code] [Range] (pL＋pH×256)＝3 (pL＝3、pH＝0) cn＝51 fn＝67...
Page 380: Fn=80: Function 380 Storing 2D Gs1 Databar Data To 2D Code Data Storage Area
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 fn=80: Function 380 Storing 2D GS1 DataBar data to 2D code data storage area GS ( k pL pH cn fn m n d1 … dk <1D>H<28>H<6B>H<pL><pH><cn><fn><m><n><d1…dk>...
Page 381: Gray Scale Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.18 Gray Scale Commands GS ( z GrayBMP, size,height,bitcount,xL,yL,xpixel,ypixel,d1…dk [Function] Print of the gray scale raster graphics [Code] <1D>H<28>H<7A>H<kind1…10><size1,2,3,4><height1,2><bitcount1,2> <xL><yL><xpixel1,2,3,4><ypixel1,2,3,4>[d1…dk] [Range] kind1=71("G"), kind2=114("r"), kind3=97("a"), kind4=121("y"), kind5=66("B ") kind6=77("M"), kind7=80("P "), kind8,9,10=32("...
Page 382 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Outline] [The specification which is common to the model] CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D151/CT-E651 • Gray Scale raser graphics is printed. • Size specifies the number of bytes after height1.
Page 383 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ( z WaterMark ,size,start,kc1,kc2,pass,feed,repeat [Function] Specifying WaterMark Printing [Code] <1D>H<28>H<7A>H<kind1～10><size1,2,3,4><start><kc1><kc2> <pass1,2,3,4><feed1,2,3,4><repeat1,2,3,4> [Range] kind1=87("W"), kind2=97("a"), kind3=116("t")、kind4=101("e"), kind5=114("r") kind6=77("M"), kind7=97("a"), kind8=114("r"), kind9=107("k"), kind10=32(" ") size=15 *size = size1+size2×256+size3×65536+size4×16777216...
Page 384 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Outline] [The specification which is common to the model] CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D151/CT-E651 • Start and End of watermark printing are specified. (Starting: start = 1, Endign: start = 0) •...
Page 385: Other Commands
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 2.2.19 Other Commands DLE ENQ n [Function] Real-time request to printer [Code] <10>H<05>H<n> [Range] 0≤ n≤ 2 [Outline] [The specification which is common to the model] •...
Page 386: Dle Dc4 Fn M T (Specification Of Fn = 1)
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 DLE DC4 fn m t (Specification of fn = 1) [Function] Outputting specified pulse in real-time [Code] <10>H<14>H<fn><m><t> [Range] fn=1, m=0, 1 1 ≤ t ≤ 8...
Page 387: Dle Dc4 Fn D1
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 DLE DC4 fn d1...d7 (Specification of fn = 8) [Function] Buffer clear [Code] <10>H<14>H<fn><d1> …<d7> [Range] fn=8, d1=1, d2=3, d3=20, d4=1, d5=6, d6=2, d7=8...
Page 388: Esc = N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC = n [Function] Data input control [Code] <1B>H<3D>H<n> [Range] 0≤n≤255 [Outline] [The specification which is common to the model] • Selecting equipment for which data input from the host is valid.
Page 389: Esc
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC @ [Function] Initializing the printer [Code] <1B>H<40>H [Outline] [The specification which is common to the model] • Clears data stored in the print buffer and brings various settings to the initial state (Default state).
Page 390: Esc L
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC L [Function] Selecting PAGE MODE [Code] <1B>H<4C>H [Outline] [The specification which is common to the model] • Switches from STANDARD MODE to PAGE MODE.
Page 391: Esc S
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC S [Function] Selecting STANDARD MODE [Code] <1B>H<53>H [Outline] [The specification which is common to the model] • Switches from PAGE MODE to STANDARD MODE.
Page 392: Esc P M N1 N2
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC p m n1 n2 [Function] Generating the specified pulses [Code] <1B>H<70>H<m><n1><n2> [Range] m=0, 1, 48, 49 0<n1≤n2≤255 [Outline] [The specification which is common to the model] •...
Page 393 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS ( A pL pH n m [Function] Execution of test printing [Code] <1D>H<28>H<41>H<pL><pH><n><m> [Range] (pL+(pH×256))=2 (pL=2, pH=0) 0≤n≤2, 48≤n≤50 1≤m≤4, 49≤m≤52 [Outline] [The specification which is common to the model] •...
Page 394 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Caution] [The specification which is common to the model] • This command is only valid when processed at the head of a line during the STANDARD MODE.
Page 395: Gs I N
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS I n [Function] Sending the printer ID [Code] <1D>H<49>H<n> CT-S280/ CT-S601(II)/CT-S651(II)/CT-P29x series/ CT-S310II/ CT-S251/ [Range] CT-D150/CT-E351/CT-D151/CT-E651 1≤n≤3, 49≤n≤51, 65≤n≤67, n=69, 112 CT-S281/CT-S300/CT-S310/ CT-S2000/CT-S4000/CT-S801(II)/CT-S851(II) 1≤n≤4, 49≤n≤52, 65≤n≤67, n=69, 112...
Page 396 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S280 • Sends printer information specified by n=65 or more. Hex. Number of Data Type of Printer ID Specification Value (Hex.) Header 1, 49...
Page 397 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S281 • Printer information configuration on and after transmitted n=65 is shown Type of Printer ID Specification Value (Hex.) below. 1, 49 CT-S281 Model ID...
Page 398 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S300/CT-S310 • Printer information configuration on and after transmitted n=65 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer CT-S300,CT-S31...
Page 399 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S310II • Sends printer information specified by n=65 or more. Hex. Number of Data Type of Printer ID Specification Value (Hex.) Header 1, 49...
Page 400 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • Printer information configuration on and after transmitted n=65 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer 1, 49...
Page 401 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S2000 • DSW If n=112 is specified: Function Hex. Decimal Dip switch [DSW8] is OFF Dip switch [DSW8] is ON Dip switch [DSW7] is OFF...
Page 402 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • Printer information configuration on and after transmitted n=65 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer 1, 49...
Page 403 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S4000 • DSW If n=112 is specified: Function Hex. Decimal Dip switch [DSW8] is OFF Dip switch [DSW8] is ON Dip switch [DSW7] is OFF...
Page 404 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851/CT-S601/CT-S651 • Printer information configuration on and after transmitted n=65 is shown below. Kind of Printer Type of Printer ID Specification Value (Hex.) Information...
Page 405 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S801/CT-S851/CT-S601/CT-S651 • Security / Connect Device If n = 94 is specified. • Bluetooth communication information on and after transmitted n=90 is Value Function shown below.[CT-S801II/CT-S851II/CT-S601II/CT-S651II]...
Page 406 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-S251 • Bluetooth communication information on and after transmitted n=90 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer 1, 49...
Page 407 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-P29x series • Sends printer information specified by n=65 or more. Hex. Number of Data Type of Printer ID Specification Value (Hex.) Header 1, 49...
Page 408 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D150 • Sends printer information specified by n=65 or more. Hex. Number of Data Type of Printer ID Specification Value (Hex.) Header 1, 49...
Page 409 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E351 • Sends printer information specified by n=65 or more. Hex. Number of Data Type of Printer ID Specification Value (Hex.) Header 1, 49...
Page 410 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-D151 • Bluetooth communication information on and after transmitted n=90 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer 1, 49...
Page 411 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 CT-E651 • Bluetooth communication information on and after transmitted n=90 is shown below. Type of Printer ID Specification Value (Hex.) Kind of Printer 1, 49...
Page 412: Gs P X Y
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS P x y [Function] Specifying the basic calculation pitch [Code] <1D>H<50>H<x><y> [Range] 0≤x≤255, 0≤y≤255 [Outline] [The specification which is common to the model] •...
Page 413 CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 [Default] x=203 [The specification which is common to the model] CT-S280/CT-S281/CT-S300/CT-S310/CT-P29x series y = 360 CT-S2000/CT-S4000 CT-S801(II)/CT-S851(II)/CT-S601(II)/CT-S651(II)/CT-S310II /CT-S251/CT-D150/CT-E351/CT-D151/CT-E651 MSW5-2 OFF y=360 MSW5-2 ON y=406 [See Also] Appendix 5.1 “Explanation on PAGE MODE”...
Page 414: Esc Rs
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 ESC RS [Function] Sound buzzer [Code] <1B>H<1E>H [Outline] [The specification which is common to the model] • Sound the buzzer for 200 ms. [Caution] [The specification which is common to the model] •...
Page 415: Gs R 2 N T1 T2
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351 Support model CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II CT-D151/E651 GS R 2 n t1 t2 [Function] Controlling bezel LED [Code] <1D>H<52>H<32>H<n>H<t1>H<t2> 0≤n≤2, 48≤n≤50 [Range] 0, 2≤t1≤255, 0, 2≤t2≤255 [Outline] This command controls Bezel LED.
Page 416: Character Code Table
3. CHARACTER CODE TABLE 3.1 Code Page 3.1.1 Codepage 00H to 7FH & PC437 (USA, Europe Standard) ░ └ ╨ α ≡ Ç É á NUL DLE ▒ ┴ ╤ β ü æ í ± ▓ ┬ ╥ Γ ≧ "...
Page 417: Codepage 00H To 7Fh & Katakana
3.1.2 Codepage 00H to 7FH & Katakana ┴ ═ ▁ タミ × NUL DLE ┬ ╞ ▂ アチム円 º ┤ ┌ ╪ ▃ イツメ年 " ├ ┘ ╡ ▅ ウテモ月 XOFF ─...
Page 418: Codepage 00H To 7Fh & Pc850 (Multilingual)
3.1.3 Codepage 00H to 7FH & PC850 (Multilingual) ░ └ Ç É á ð Ó NUL DLE ▒ ┴ β ü æ í Ð ± ▓ ┬ " é Æ ó Ê Ô │ ├ â ô ú Ë Ò ¾...
Page 419: Codepage 00H To 7Fh & Pc860 (Portuguese)
3.1.4 Codepage 00H to 7FH & PC860 (Portuguese) ░ └ ╨ α ≡ Ç É á NUL DLE ▒ ┴ ╤ β ü À í ± ▓ ┬ ╥ Γ ≧ " é È ó │ ├ ╙ π ≤ â...
Page 420: Codepage 00H To 7Fh & Pc863 (Canadian-French)
3.1.5 Codepage 00H to 7FH & PC863 (Canadian-French) ░ └ ╨ α ≡ ￤ Ç É NUL DLE ▒ ┴ ╤ β ü È ´ ± ▓ ┬ ╥ Γ ≧ " é Ê ô │ ├ ╙ π ≤ â...
Page 421: Codepage 00H To 7Fh & Pc865 (Nordic)
3.1.6 Codepage 00H to 7FH & PC865 (Nordic) ░ └ ╨ α ≡ Ç É á NUL DLE ▒ ┴ ╤ β ü æ í ± ▓ ┬ ╥ Γ ≧ " é Æ ó │ ├ ╙ π ≤ â...
Page 422: Codepage 00H To 7Fh & Pc852 (Eastern Europe)
3.1.7 Codepage 00H to 7FH & PC852 (Eastern Europe) ░ └ đ Ç É á Ó NUL DLE Ĺ ▒ ┴ Đ β ü í ” ▓ ┬ Ď " é Í ó Ó │ ├ Ń ˇ â ô ú...
Page 423: Codepage 00H To 7Fh & Pc866 (Russian)
3.1.8 Codepage 00H to 7FH & PC866 (Russian) Α Р а ░ └ ╨ р Ë NUL DLE Б С б ▒ ┴ ╤ с ë В Т в ▓ ┬ ╥ т Є " Г У г │ ├ ╙...
Page 424: Codepage 00H To 7Fh & Pc857 (Turkish)
3.1.9 Codepage 00H to 7FH & PC857 (Turkish) ░ └ Ç É á ó NUL DLE ▒ ┴ β ü æ í ± ▓ ┬ " é Æ ó Ê ô │ ├ â ô ú Ë ò ¾ ┤ ─...
Page 425: Codepage 00H To 7Fh & Pc864 (Arabic)
3.1.10 Codepage 00H to 7FH & PC864 (Arabic) - 424 -...
Page 426: Codepage 00H To 7Fh & Wpc1252
3.1.11 Codepage 00H to 7FH & WPC1252 ° À Ð à ð NUL DLE ‘ ¡ ± Á Ñ á ñ " ¸ ’ ¢ ² Â Ò â ò ƒ “ £ ³ Ã Ó ã ó ” ¤ ´...
Page 427: Codepage 00H To 7Fh & Thai Code 11
3.1.12 Codepage 00H to 7FH & Thai code 11 - 426 -...
Page 428: Codepage 00H To 7Fh & Thai Code 18
3.1.13 Codepage 00H to 7FH & Thai code 18 - 427 -...
Page 429: Codepage 00H To 7Fh & Tcvn-3 (Vietnamese)
3.1.14 Codepage 00H to 7FH & TCVN-3 (Vietnamese) TCVN-3 é NUL DLE Ă ẹ ỏ ủ ề ũ " Â õ ể Ê ó ú ễ ọ ụ Ô Ơ ế ồ ừ à Ư ả ặ ệ ổ ử &...
Page 430: International Character Code Table
3.2 International Character Code Table Country ╲ U.S.A à ° ç § é ù è ¨ France β § Ä Ö Ü ä ö ü Germany ╲ £ U.K. @ Æ Ø Å æ ø å Denmark I ¤ É Ä...
Page 431: Memory Switch
4. Memory Switch Memory switch is a function to save the user selected settings into NV memory, where memory switch setting will be held unless memory switch is changed. Memory switch is changed by manual setting or by command in the memory switch change mode. * Hereafter, memory switch is referred to as MSW.
Page 432 Setting Default Set Values 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control Xon/Xoff DTR/DSR, Xon/Xoff MSW7-6 Reserved MSW7-7...
Page 433: Ct-S281
4.1.2 CT-S281 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print “?” MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 434 Setting Default Set Values 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control Xon/Xoff DTR/DSR, Xon/Xoff MSW7-6 Reserved MSW7-7 VCom Protocol PC setting...
Page 435: Ct-S300
4.1.3 CT-S300 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 436: Ct-S310
4.1.4 CT-S310 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print “?” MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 437 Setting Default Set Values 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control Xon/Xoff DTR/DSR, Xon/Xoff MSW7-6 Reserved MSW7-7 VCom Protocol PC setting...
Page 438: Ct-S310Ii
4.1.5 CT-S310II Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 439 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 440: Ct-S2000
4.1.6 CT-S2000 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 441 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 442: Ct-S4000
4.1.7 CT-S4000 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print “?” MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 443 Setting Default Set Values 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 444: Ct-S801/851
4.1.8 CT-S801/851 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 445 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 446: Ct-S601/651
4.1.9 CT-S601/651 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 447 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 448: Ct-S801 Ii/Ct-S851 Ii
4.1.10 CT-S801 II/CT-S851 II Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ●...
Page 449 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 450 <<Difference of MSW by the model>> MSW4-4 and MSW4-5 are different by the model as follows. Model Standard Black mark model Label model Black mark paper/ Black mark paper/ MSW4-4 Thermal paper Label paper Label paper MSW4-5 Black mark detection Black mark detection Label detection - 449 -...
Page 451: Ct-S601 Ii/Ct-S651 Ii
4.1.11 CT-S601 II/CT-S651 II Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ●...
Page 452 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 453: Ct-S251
4.1.12 CT-S251 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 454 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 455: Ct-P29X Series
4.1.13 CT-P29x series Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size *1 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print “?” MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ●...
Page 456 Setting Default Set Values 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 Reserved MSW7-7...
Page 457: Ct-D150
4.1.14 CT-D150 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed...
Page 458 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 9600bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 459: Ct-E351
4.1.15 CT-E351 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 460 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 461: Ct-D151
4.1.16 CT-D151 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 462 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 463: Ct-E651
4.1.17 CT-E651 Setting ● Valid MSW1-1 Power ON Info Not send ● 4K bytes MSW1-2 Buffer Size 45 bytes ● Full/Err MSW1-3 Busy Condition Full ● Print ? MSW1-4 Receive Error No Print ● Ignored MSW1-5 CR mode ● Fixed MSW1-6 Reserved ●...
Page 464 Setting Default Set Values 1200 bps, 2400bps, 4800bps, 9600bps, 19200bps, MSW7-1 Baud Rate 19200bps 38400bps, 57600bps, 115200bps MSW7-2 Data Length 8bits 7bits, 8bits MSW7-3 Stop Bit 1bit 1bit, 2bits MSW7-4 Parity None None, Odd, Even MSW7-5 Flow Control DTR/DSR DTR/DSR, Xon/Xoff MSW7-6 DMA control Valid...
Page 465: Details Of Memory Switches
4.2 Details of Memory Switches This section describes the function of memory switch. Some MSW may not be set or some values may not be selected depending on the model used. For the MSW and value that can be set or selected with the model you are using, refer to the operation manual or the like.
Page 466 ●MSW1-3: Busy condition [Outline] Select the condition that printer is BUSY . Automatic status send function also runs. OFF(0) ON(1) Busy Condition Buffer full/Off-line Buffer full ON (1) OPERATION: If receive buffer is full, printer is BUSY . Automatic status send (ASB) function is enabled. OFF (0) OPERATION: If receive buffer is full or off-line, printer is BUSY .
Page 467 ●MSW1-5: CR code [Outline] Select the printer when receiving CR(<0D>H) code. OFF(0) ON(1) CR mode Ignored ON (1) OPERATION: Select the same operation with LF when receiving CR code. Print data in print buffer and put linefeeds as specified. OFF (0) OPERATION: CR code may be ignored with no actions if receiving CR code.
Page 468: Msw2
4.2.2 MSW2 ●MSW2-1: Reserved [Fixed to ON(1)] ●MSW2-2: Auto-cutter operation [Outline] Select auto-cutter enable/disable. OFF(0) ON(１) Auto Cutter Invalid Valid ON (1) OPERATION: Auto-cutter enabled OFF (0) OPERATION: Auto-cutter disabled ●MSW2-3: Buffering [Outline] Select buffering print enable/disable. OFF(0) ON(1) Spool Print Invalid Valid ON (1) OPERATION: Buffering print is enabled.
Page 469 ●MSW2-4: Full Columns print [Outline] Select the processing if print data closes to the end of line or the right of print width. OFF(0) ON(1) Full Col print Line Feed Wait Data ON (1) OPERATION: If printer receives data/command exceeding the full column, printer further waits for print data. If data exceeding the full column is a command, printer operates following the command.
Page 470 ●MSW2-6: Paper width [Outline] Select paper width. OFF(０) ON(１) Paper width 80mm 58mm ON (1) OPERATION: Paper width is set 80mm OFF (0) OPERATION: Paper width is set 58mm ●MSW2-7: Reserved [Fixed to OFF (0)] ●MSW2-8: PNE sensor [Outline] Select paper near-end enable/disable. OFF(0) ON(1) PNE Sensor...
Page 471: Msw3
4.2.3 MSW3 ●MSW3-1: Auto-cutter return [Outline] Selects the return method from cutter lock error. OFF(0) ON(1) Resum Cttr Err Valid Invalid ON (1) OPERATION: Return by command. After removing error cause, return with command <DLE ENQ n>. OFF (0) OPERATION: Return with FEED switch. After removing error cause, return by long pressing FEED SW (1 sec or longer).
Page 472 ●MSW3-3: Parallel 31 pin [Outline] Printer can be reset by parallel I/F –31 Pin signal. Select the handling of this signal. OFF(0) ON(1) Parallel 31 pin Valid Invalid ON (1) OPERATION: Used as reset signal OFF (0) OPERATION: Not used as reset signal ●MSW3-4: Selecting paper [Outline]...
Page 473 ●MSW3-8: Cover open during printing [Outline] Select the release method of cover open error during printing. OFF(0) ON(1) Resum Open Err Close Command ON (1) OPERATION: Cover open error during printing becomes a return allowed error. Returned with command <DLE ENQ n> after cover is closed. OFF (0) OPERATION: Cover open error during printing becomes an automatic return error.
Page 474: Msw4
4.2.4 MSW4 ●MSW4-1: Automatic length measurement [Outline] In selecting black mark paper, set the enable/disable of automatic length measurement. (Black mark/label support model only) OFF(0) ON(1) BM Measure Invalid Valid ON (1) OPERATION: Automatic length measurement is enabled. At power-up, measurement operation is taken. OFF (0) OPERATION: Automatic length measurement is disabled.
Page 475 ●MSW4-3: Paper feed & cut at closing cover [Outline] When cover is closed, printer feeds paper and cuts. OFF(0) ON(1) Feed & Cut at TOF Invalid Valid ON (1) OPERATION: Paper feed & cut at closing cover is enabled. OFF (0) OPERATION: Paper feed & cut at closing cover is disabled. ●MSW4-4: Paper [Outline] Selects the type of paper used.
Page 476 ●MSW4-6: Behavior by cover close (CT-S281 unique) [Outline] Selects the behavior at closing cover for black mark or label OFF(0) ON(1) C.Close Action Find TOF Auto Measure ON (1) OPERATION: Feed paper to find top of form OFF (0) OPERATION: MSW4-1 On - Performs automatic length measurement.
Page 477 ●MSW4-8: Forcible partial cut [Outline] Select the operation taken when full cut command is received. OFF(0) ON(1) Partial only Invalid Valid ON (1) OPERATION: When full cut command is received, partial cut, not full cut, is taken. OFF (0) OPERATION: When full cut command is received, full cut is taken. - 476 -...
Page 478: Msw5
4.2.5 MSW5 ●MSW5-1: Buzzer [Outline] Select the enable/disable of buzzer. OFF(0) ON(1) Buzzer Valid Invalid ON (1) OPERATION: Disable buzzer When an error occurs or memory switch setting is changed manually, no buzzer sounds. OFF (0) OPERATION: Enable buzzer. When an error occurs or memory switch setting is changed manually, the buzzer sounds. ●MSW5-2: Basic vertical calculation pitch [Outline]...
Page 479 ●MSW5-5: Setting the power OFF notify (Only for CT-S4000) [Outline] At power OFF, to notify the host of the printer power OFF, printer can send to host 3 byte power OFF notify status data ( 3BH 31H 00H). Set to enable/disable for sending the power OFF notify status data. OFF(0) ON(1) Power OFF Info...
Page 480 ●MSW5-6： Auto Back Feed (CT-S281 unique) Selects the behavior of GS+FF (print and black mark/label ejection) command [Outline] OFF(0) ON(1) Auto Back Feed After Cut Before Print After the cut, paper stay there and when printer receives next print data, the back ON (1) OPERATION: feeding paper to top of form is done.
Page 481: Msw6
4.2.6 MSW6 ●MSW6-1: Mode to use with the driver [Outline] Selects the valid/invalid of mode to use with the driver OFF(0) ON(1) Mode to use with the driver Invalid Valid ON (1) OPERATION: FAULT signal is not output in the error condition to parallel port.. ASB is valid at power on.
Page 482 ●MSW6-8： Power On Trigger (CT-D150/CT-E351/CT-D151/ CT-E651 unique) Select what trigger makes the printer turn on. [Outline] OFF(0) ON(1) Power On Trigger Power Switch ON AC Power Input ON (1) OPERATION: Printer turns on by the AC power input. OFF (0) OPERATION: Printer turns on by the power switch.
Page 483: Msw7
4.2.7 MSW7 ●MSW7-1: Baud rate [Outline] Selects the baud rate which is serial interface communication condition. Enabled if DSW1-1 OFF is set [following memory switch setting] . Setting Value 1200bps,2400bps,4800bps,9600bps,19200bps, Baud Rate 38400bps,57600bps,115200bps ●MSW7-2: Data length [Outline] Selects the data length, which is a serial interface communication condition. Enabled if DSW1-1 OFF is set [following memory switch setting] .
Page 484 ●MSW7-6: DMA control [Outline] Selects the valid/invalid of DMA (Direct Memory Access) control. Setting Value DMA control Valid, Invalid ●MSW7-7: VCom flow control [Outline] In MSW5-3, selects the flow control when virtual COM is set. Setting Value VCom Protocol PC setting, DTR/DSR, XON/XOFF - 483 -...
Page 485: Msw8
4.2.8 MSW8 ●MSW8-1: Print width [Outline] Selects the print width in dots. Setting Value 832dots, 720dots, 660dots, 640dots, 576dots, Print Width 512dots, 436dots, 432dots, 420dots, 384dots, 360dots, 390dots, 546dots ●MSW8-2: Paper type [Outline] Selects the paper type used. Setting Value Paper Type 1 Color Normal, 2 color Normal ●MSW8-3：...
Page 486 MSW 8-1 Print Width = edit area width, actual print width is reduced by 75 %. *In case of setting 512 dots: edit area width 512 dots, print width 384 dots. (CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D150/CT-D151/CT-E351/CT-E651 unique) MSW 8-1 Print Width ÷ 75% becomes the edit area width, print area width = actual print width.
Page 487 ●MSW8-6： Auto Side slide (CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-S251/CT-D150/CT-D151/CT-E351/CT-E651 unique) [Outline] Select the sliding length to the side Setting Value Auto Side Shift Invalid, 1dot, 2dot, 3dot, 4dot, 5dot, 6dot, 7dot This memory switch sets the slide amount in the horizontal direction. This is a function to prevent the specific part from wearing out quickly by dispersing the load of heat generation when printing vertical ruled lines or the like with a large number of heat generation at specific parts of the head heating element.
Page 488: Msw9
Setting Value JIS/Shift JIS JIS, Shift JIS Setting Value JIS/Shift JIS JIS, Shift JIS(CP932), Shift JIS (X0213) ●MSW9-4： Kanji Code (CT-S801II/CT-S851II/CT-S601II/CT-S651II/CT-D150/CT-E351/CT-D151/CT-E651 unique) Selects the Kanji Code System. [Outline] Setting Value Invalid, JIS(JPN), SJIS:CP932(JPN), SJIS:X0213(JPN), GB18030(CHN)、 Kanji Code KS Hangul(KOR)、EUC Hangul(KOR)、...
Page 489 ●MSW9-5: Reserved [Fixed to OFF (0)] ●MSW9-6: Language for LCD message [Outline] Selects the language of message shown on the LCD. Setting Value English, Français, Deutsch, Italiano, LCD Language Español, Japanese, Chinese ●MSW9-7: LCD download message [Outline] Selects the valid/invalid of download message for LCD. Setting Value LCD Ext.
Page 490: Msw10
Selects the [Outline] user NV memory capacity. Setting Value NV User 1Kbytes,64Kbytes,128Kbytes,192Kbytes ●MSW10-4: Emulation Type (CT-S310II/CT-S801(II)/CT-S851(II)/CT-S251/CT-D150/CT-E351/CT-D151/CT-E651 unique) Selects the emulation of old dot matrix printers [Outline] Setting Value Emulation Type ESC/POS, CBM1, CBM2 ●MSW10-5: NV graphics memory capacity (CT-S2000/CT-S4000 unique)
Page 491 ●MSW10-5： Buzzer event (CT-S801(II)/CT-851(II)/CT-S601(II)/CT-651(II)/CT-S251/CT-D150/CT-E351/CT-D151/CT-E651 unique) [Outline] Selects the events of the printer to activate the buzzer. Setting Value Buzzer Event All, Not by C.Open, Not by C.Open/PE If “Not by C.Open” is selected, buzzer is not acticated by opening cover.
Page 492: Msw11
4.2.11 MSW11 ●MSW 11-1： Bezel LED [Outline] Selects the Control Bezel LED Setting Value Bezel LED Off, On, Blink, Blink by Recv 4.2.11 MSW13 ●MSW 13-1： BT Security 1 (CT-S281BD Model unique) Set the Bluetooth security level together with MSW13-2. [Outline] OFF(0) ON(1)
Page 493 ●MSW13-5： BT Device Scan Set the behavior against the Bluetooth device scan. [Outline] OFF(0) ON(1) BT Device Scan No Response Discoverable ON (1) OPERATION: Printer does not respond against Bluetooth device scan. OFF (0) OPERATION: Printer is discoverable from any Bluetooth device,. ●ＭＳＷ13-6：...
Page 494: Appendix
5. APPENDIX 5.1 Explanation on PAGE MODE 5.1.1 Overview The printer has two print modes: STANDARD and PAGE. In STANDARD MODE, the printer prints or feeds paper each time it receives a print or paper feed command. In PAGE MODE, when the printer receives print commands and/or form feed commands, it simply forwards them to the specified print area of memory.
Page 495: Mapping Of Print Data In The Print Area
5.1.3 Mapping of Print Data in the Print Area Print data is mapped in the print area as follows: (1) The print area is set by ESC W. When the printer has finished all of the print and paper feed actions specified before receiving an ESC W, the ESC W sets the right end (as viewed facing the printer) as the start point (x0, y0) of the print area.
Page 496 Mapping direction x0, y0 24-3 Baseline Point A dx, dy Print area Figure 5-1 Mapping Position for Character Data Bar code GS k m ＝ nH*256+nL 24-3 Bit image GS * x y ESC * m nL nH Baseline (HRI Characters) Point B Point B Point B...
Page 497: Example Of Using
5.1.4 Example of Using PAGE MODE The following explains specific uses of PAGE MODE. When in PAGE MODE, the commands are typically sent from the host to the printer in the following sequence: (1) An ESC L puts the printer in PAGE MODE. (2) An ESC W specifies the print area.
Page 498 In Figure 4-3, a line feed occurs between “lesson” and “Test 1” because the space “ “ next to “lesson” does not fit in the horizontal range of the 200 -pitch print area. The line feed width conforms to the value specified by a command such as ESC 3.
Page 499 (0,0) 200 Page mode lesson Paper 2CAN command ABCDEFGHIJKLMNOP QRST1234567890 Print area Print Direction Figure 5-4 Example 2: Result of Print Before an FF is sent (170th line), the following program code can be added to remove part of the data. <...
Page 500 (0,0) 200 Page mode lesson Paper 2CAN command ABCDEF JKLMNOP QRST1234567890 Print area Print Direction Figure 5-5 Print Result of Adding a Program of Example 3 to Example 2 - 499 -...
Page 501: Bidirectional Parallel Interface
5.2 Bidirectional Parallel Interface Overview The interface of the printer is a Level-1 compatible device according to IEEE-P1284. It supports the communication modes described in 5.2.1 below. 5.2.1 Parallel Interface Communication Mode The parallel interface of the printer provides three communication modes as outlined below. When the printer is turned on or reset, it defaults to Compatibility mode.
Page 502: Interfacing Phases
5.2.2 Interfacing Phases Interfacing in each communication mode is divided into several phases. In addition, there is a phase for mode initialization, as well as a phase for mode switching. Interface signals may differ in name and function for different modes and different phases. Aborted Termination from Transfer...
Page 503: Negotiation
5.2.3 Negotiation Overview Usually, the printer is started in Compatibility mode, which corresponds to the Centronics interface phase. When the host intends to switch to the Nibble or Byte mode, it sends a request and negotiates with the printer. A general flow of negotiations is given below.
Page 504 Precautions (1) The Negotiation phase is triggered when the IEEE 1284 Active signal sent by the host becomes High. (2) In Compatibility mode, the time when the negotiation process begins is, as a general rule, after the host sets nStrobe to High and then the printer outputs an nAck pulse.
Page 505: Nibble Mode
Data Communication from Printer to Host Nibble Mode In this mode, data is transferred between the printer and the host through the procedure described below. The steps beginning from (1) are applicable when the Negotiation phase has switched to the Host Busy Data Available phase. If the Negotiation phase has switched to the Host Busy Data Not Available phase, the procedure starts at step (9).
Page 506 (14) Upon receiving a request for interrupt from the printer, the host responds by setting HostBusy (nAutoFd) to High. (Event (15) Finally, the printer responds to the host by setting AckDataReq (PError) to Low, and then the host moves to the Host Busy Data Available phase.
Page 507: Byte Mode
Byte Mode In this mode, data is transferred between the printer and the host through the procedure described below. The steps beginning from (1) are applicable when the Negotiation phase has switched to the Host Busy Data Available phase. If the Negotiation phase has switched to the Host Busy Data Not Available phase, the procedure starts at step (9). (1) After the negotiations for the entry into the Byte mode are complete, the host indicates that it is ready to receive data from the printer.
Page 508 The device ID is a character string that provides the ID, the type, and other information regarding the printer connected to the interface. When the printer receives a request for a device ID from the host, it replies with the following device ID: <00>H<2E>H MFG:CITIZEN； CMD:ESC/POS； MDL:CT-S300；(*) CLS:PRINTER；...
Page 509 Termination Termination is the process of returning to Compatibility mode from the Nibble or Byte modes. When performing Termination, the host sets the signals as follows: • IEEE 1284 Active (nSelectln): Low • HostBusy (nAutoFd): High (Event 22) There are two methods of Termination: (1) Termination through a handshake between the host and the printer (2) Immediate termination (1) Termination through a handshake between the host and the printer:...
Page 510: Identification Of Send Status
5.3 Identification of Send Status Because the status sent from the printer has certain fixed bits, it is possible to identify to which command the status belongs. When using ASB (Automatic Status Back), however, the first byte of ASB should be checked, and then the three consecutive bytes except for XOFF should be treated as ASB data.
Page 511: Cautions On Black Mark/Label Paper
5.4 Cautions on Black Mark/Label Paper Cautions on LF (CR), ESC J, ESC d, Page mode, Image, and barcode printing. Printing of image greater than vertical print area of BM paper/label paper used is prohibited as a rule. The user must use label while taking label size into account at all times and terminate printing of a sheet of label with FF, ESC FF or GS FF.
Page 512 If printing of image greater than inter-BM distance/label paper length (vertical print area width) is attempted, image is printed in two separated images as shown below. Barcode, Image greater than vertical print area of label paper used is printed over the label. downloaded image, In this case, head and bottom margins must be NV image,...

This manual is also suitable for:

Ct-d151 Ct-s251 Ct-s280 Ct-s300 Ct-s281 Ct-e651 ... Show all

Citizen CT-D150 Command Reference Manual

Table of Contents

1 Outline

2 Detail

3 Character Code Table

4 Memory Switch

5 Appendix

Quick Links

Command Reference

Related Manuals for Citizen CT-D150

Summary of Contents for Citizen CT-D150