Ec Declaration Of Conformity; Warranty; Technical Specifications; Troubleshooting - STEINEL iHF 3D KNX Information Manual

Install mode (test mode)
8
Install mode has the purpose of
checking for proper working order as
well for testing the detection zone.
Irrespective of light level, the light
switches ON for 10 s in response to
movement. (Status LED flashes).
Install mode has priority over all
other settings. Install mode ends
automatically after 10 minutes.
Install mode ends immediately after
pressing reset.
Note: Teach mode and Install mode
cannot be used at the same time.
Reset
9
Resets all settings to the values
selected on the light manually or to
the factory settings.
SmartRemote (optional)
(EAN 4007841 009151)
– Control via smartphone or tablet
– Replaces the remote control
– Load appropriate app and connect via
Bluetooth
8� EC Declaration of Conformity
This product complies with the requirements
defined in the following standards, legislation
and directives:
– EMC Directive 2014/30/EU
– RoHS Directive 2011/65/EU
– WEEE Directive 2012/19/EU
9� Warranty
As purchaser, you are entitled to your statutory
rights against the vendor. If these rights exist
in your country, they are neither curtailed nor
restricted by our Warranty Declaration. We
guarantee that your STEINEL Professional sen-
sor product will remain in perfect condition and
proper working order for a period of 5 years.
We guarantee that this product is free from
material-, manufacturing- and design flaws.
In addition, we guarantee that all electronic
components and cables function in the proper
manner and that all materials used and their
surfaces are without defects.
Making Claims
If you wish to make a claim, please send your
product complete and carriage paid with the
original receipt of purchase, which must show
the date of purchase and product designation,
either to your retailer or contact us at STEINEL
(UK) Limited, 25 Manasty Road, Axis Park,
Orton Southgate, Peterborough, PE2 6UP,
for a returns number. For this reason, we
recommend that you keep your receipt of
purchase in a safe place until the warranty peri-
od expires. STEINEL shall assume no liability
for the costs or risks involved in returning a
product.
For information on making claims under
the terms of the warranty, please go to
www�steinel-professional�de/garantie
If you have a warranty claim or would like to
ask any question regarding your product,
you are welcome to call us at any time on our
Service Hotline 01733 366700.
16
10� Technical specifications
Dimensions (H x W x D): 118.3 x 117 x 120 mm
Power supply: KNX bus voltage
Angle of coverage: 160°
Sensor technology: 5.8 GHz
Reach: 1-7 m, in 3 directions
Time setting: 1-255 s or 0-255 min
Recommended mounting height: 2 m
Twilight setting: 2 - 2000 lux
Max. area covered: approx. 68 m²
IP rating: IP 54
Temperature range: -20° to +50°C
11� Troubleshooting
Malfunction Cause
No power at the sensor n Fuse faulty, not switched
ON, break in wiring
n Short circuit
Sensor will not switch ON n Twilight setting in night mode
during daytime operation
n Bulb faulty
n KNX configuration
n Detection zone not properly
targeted
Sensor will not switch OFF n Continuous movement in
the detection zone
Sensor keeps switching ON/OFF n Light being operated is
located in detection zone
Remedy
n New fuse, turn ON power
switch, check wiring with
voltage tester
n Check connections
n Adjust setting
n Change bulb
n Check KNX configuration
n Readjust
n Check zone, adjust or fit
shrouds if necessary
n Change zone, or fit shrouds
n Deactivate 4 h manual
override
n Change zone or fit shrouds,
increase distance
17