Omron E5CN-HT Communications Manual page 101

Address
Four- Two- Parameter name
byte byte
mode mode
0722 2711 MV at PV Error
0726 2713 MV Change Rate Limit
072C 2716 Lower Limit Temperature Input Shift Value
0730 2718 Upper Limit Temperature Input Shift Value
0734 271A Heater Current 1 Value Monitor
0736 271B Heater Burnout Detection 1
0738 271C Leakage Current 1 Monitor
073A 271D HS Alarm 1
0746 2723 Temperature Input Shift
0748 2724 Heater Current 2 Value Monitor
074A 2725 Heater Burnout Detection 2
074C 2726 Leakage Current 2 Monitor
074E 2727 HS Alarm 2
0754 272A Wait Band
0756 272B Heater Overcurrent Detection 1
0758 272C Heater Overcurrent Detection 2
075A 272D Fixed SP
075C 272E Standby Time
075E 272F Program SP Shift Value
0800 2800 Input Digital Filter
0810 2808 Extraction of Square Root Low-cut Point
0838 281C RSP 0 before Correction
083A 281D RSP 1 before Correction
083C 281E RSP 2 before Correction
083E 281F RSP 3 before Correction
0840 2820 RSP 4 before Correction
0842 2821 RSP 5 before Correction
0844 2822 RSP 6 before Correction
0846 2823 RSP 7 before Correction
0848 2824 RSP 8 before Correction
084A 2825 RSP 9 before Correction
084C 2826 RSP 10 before Correction
084E 2827 RSP Broken-line Correction Value 0
0850 2828 RSP Broken-line Correction Value 1
0852 2829 RSP Broken-line Correction Value 2
0854 282A RSP Broken-line Correction Value 3
0856 282B RSP Broken-line Correction Value 4
0858 282C RSP Broken-line Correction Value 5
085A 282D RSP Broken-line Correction Value 6
085C 282E RSP Broken-line Correction Value 7
085E 282F RSP Broken-line Correction Value 8
0860 2830 RSP Broken-line Correction Value 9
0862 2831 RSP Broken-line Correction Value 10
1800 3800 Program Selection
5.1 Variable Area (Setting Range) List
Setting (monitor) value
Standard: H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
Heating/cooling: H'FFFFFBE6 to H'0000041A (−105.0 to 105.0)
Position proportional (Floating or direct setting of position propor-
tional MV OFF): H'FFFFFFFF to H'00000001 (−1 to 1)
Position proportional (Closed and direct setting of position propor-
tional MV ON): H'FFFFFFCE to H'0000041A (−5.0 to 105.0)
H'00000000 to H'000003E8 (0.0 to 100.0)
H'FFFFB1E1 to H'00007E90 (−199.99 to 324.00)
H'FFFFB1E1 to H'00007E90 (−199.99 to 324.00)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'FFFFB1E1 to H'00007E90 (−199.99 to 324.00)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'00000226 (0.0 to 55.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 (0): OFF
Temperature: H'00000001 to H'00007E90 (0.1 to 3240.0)
Analog: H'00000001 to H'0000270F (0.01 to 99.99)
H'00000000 to H'000001F4 (0.0 to 50.0)
H'00000000 to H'000001F4 (0.0 to 50.0)
SP lower limit to SP upper limit
H'00000000 to H'00009959 (hours, minutes)
H'00000000 to H'00009923 (days, hours)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'00000000 to H'0000270F (0.0 to 999.9)
H'00000000 to H'000003E8 (0.0 to 100.0)
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
Remote SP lower limit to remote SP upper limit
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'FFFFB1E1 to H'00007E90 (−19999 to 32400)
H'00000000 to H'00000007 (0 to 7)
Level
Adjustment
Operation
Adjustment
Operation
Adjustment
Operation
Adjustment
Operation
Adjustment
Advanced
function
setting
Adjustment
Program
5-5