Sony HVR-Z5C Service Manual page 180

4. B Page table
Note 1: Check that the data of page: 0, address: 10 is "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the A, B, D, 1A, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of A, B, D, 1A, 1B Page Data")
Initial value
Address
NTSC PAL
00 to B0
B1
B2 to FF
5. D Page table
Note 1: Check that the data of page: 0, address: 10 is "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the A, B, D, 1A, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of A, B, D, 1A, 1B Page Data")
Initial value
Address
NTSC PAL
10 to FF
6. 1A Page table
Note 1: If reading/writing data on pages 1A, set data: 01 to page:
0, address: 10, and then select pages: A. By this data set-
ting, the pages 1A can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the A, B, D, 1A, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of A, B, D, 1A, 1B Page Data")
Initial value
Address
NTSC PAL
00 to FF
7. 1B Page table
Note 1: If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages: B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to "00".
Note 2: Fixed data-1: Initialized data. (Refer to "1. Initializing
the A, B, D, 1A, 1B Page Data")
Fixed data-2: Modified data. (Refer to "2. Modification
of A, B, D, 1A, 1B Page Data")
Initial value
Address
NTSC PAL
00 to FF
HVR-Z5C/Z5E/Z5J/Z5N/Z5P/Z5U
Remark
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Remark
Fixed data-1 (Initialized data)
Remark
Fixed data-1 (Initialized data)
Remark
Fixed data-1 (Initialized data)
1-2-2. Initialization of 8, 9, C, 13, 18, 1C, 1D, 1E
Page Data
1. Initializing of 8, 9, C, 13, 18, 1C, 1D, 1E Page Data
Note 1: If "Initialization of Pages 8, 9, C, 13, 18, 1C, 1D, 1E" is
executed, all data on pages 8, 9, C, 13, 18, 1C, 1D, 1E
are initialized. (Only an individual page cannot be ini-
tialized)
Note 2: If the 8, 9, C, 13, 18, 1C, 1D, 1E page data has been
initialized, the following adjustments need to be per-
formed again.
1) Modification of 8, 9, C, 13, 18, 1C, 1D, 1E page data
2) Electronic viewfinder system adjustments (if all ar-
eas were initialized)
3) LCD system adjustments (if all areas were initial-
ized)
4) Node unique ID No. input (if all areas were initial-
ized)
5) Servo, RF system adjustments (if all areas were ini-
tialized)
6) Video system adjustments (if all areas were initial-
ized)
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Adjustment Page
Adjustment Address
Initializing method:
Order Page Address Data
1 0 01
2 0 10
3 3 81
4 3 80
5 3 80
6 3 91
7 3 90
6-10
8
00 to FF
9
00 to FF
C
10 to FF
13
00 to FF
18
00 to FF
1C
00 to FF
1D
00 to FF
1E
00 to FF
Procedure
01
00
Set the following data. (Note
3)
00: Initializing all areas
01: Initializing other than
adjustment address
0C Press PAUSE (Write) button.
Check the data changes to
"1C".
Set the following data. (Note
3)
09: Initializing all areas
19: Initializing other than
adjustment address
0C Press PAUSE (Write) button.