Adjusting The Sound - Kenwood VR-6060 Instruction Manual

Normal playback

Adjusting the sound

SPEAKERS A/B TONE
PHONES LOUDNESS
MUTE
LOUDNESS
Adjusting the TONE
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo mode.
1 Press the TONE key to select the TONE mode.
2 Use the MULTI CONTROL knob or Joystick to select TONE
ON/OFF.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG 96kHzfs
L C SW R
LFE
SL S SB SR
3 When in TONE ON selection, pressing the TONE key will
display the level of BASS or TREBLE.
BASS : Select this to adjust the low frequency range.
TREBLE : Select this to adjust the high frequency range.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG 96kHzfs
L C SW R
LFE
SL S SB SR
4 Use the MULTI CONTROL knob or Joystick to adjust the sound
quality.
• The bass and treble levels are adjustable from -10dB to +10dB in 2
step increments.
• The adjustment item is displayed for approximately 8 seconds.
SP MUTE OPTICAL 6CH INPUT
AUTO DETECT
A B CLIP
COAXIAL ANALOG 96kHzfs
L C SW R
LFE
SL S SB SR
Once-touch low frequency emphasis (bass boost)
(remote control only)
You can adjust the sound quality when the receiver is in the PCM stereo
and analog stereo modes.
Press the B. BOOST key.
• Press the key once to select the maximum (+10dB) low frequency
emphasis setting.
• This key does not function when the receiver is in the sound quality or
ambience effects adjustment mode.
Switching back to the previous setting
Press the B. BOOST key again.
•VR609/20-28/EN
MULTI CONTROL
MUTE VOLUME
CONTROL
RECEIVER
CINEMA EQ
ACTIVE EQ
RCV. VOL. +/—
Joystick (UP/DOWN)
B. BOOST
TONE
RDS
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
RTY
Surround EX
DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
RDS
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6
THX
ACTIVE EQ. MATRIX
RTY
Surround EX
DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 RDS
THX
ACTIVE EQ. MATRIX
RTY
Surround EX
DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII
AUTO
MEMO
STEREO
TUNED
25
Adjusting the LOUDNESS
You can adjust the Loudness function which controls the low volume
settings to maintain the music's richness.
Press the LOUDNESS key to turn the LOUDNESS setting ON/OFF.
1 LOUDNESS ON : The LOUDNESS indicator lights up.
2 LOUDNESS OFF : The LOUDNESS indicator goes off.
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
SP MUTE
A B CLIP
L C SW R
LFE
SL S SB SR
Blinks
To cancel
Press the MUTE key again so that the "MUTE" indicator goes off.
• MUTE ON can also be deactivated by turning the VOLUME
CONTROL knob.
CINEMA EQ mode
You can enjoy a more impressive sound effect when you switch CINEMA
EQ ON during Dolby Digital and DTS playback.
Press the CINEMA EQ key to turn the CINEMA EQ setting ON/OFF.
1 CINEMA EQ ON : The CINEMA EQ indicator lights up.
2 CINEMA EQ OFF : The CINEMA EQ indicator goes off.
ACTIVE EQ mode
AAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAA AA.
Press the ACTIVE EQ key to switch the following setting:
1 ACTIVE EQ ON : The ACTIVE EQ indicator lights up.
2 ACTIVE EQ OFF : The ACTIVE EQ indicator goes off.
Listening with headphones
1 Press the SPEAKERS A or B keys so that the speaker indicator
goes off.
Make sure the SPEAKERS
indicators are turned off.
SP MUTE
A B CLIP
L C SW R
LFE
SL S SB SR
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo play-
back.
2 Connect headphones to the PHONES jack.
PHONES
3 Use the VOLUME CONTROL knob or RCV. VOL. +/- keys to
adjust the volume.
10/24/01, 10:37 PM
OPTICAL 6CH INPUT CINE
AUTO DETECT
ACT
COAXIAL ANALOG 96kHzfs DSP
OPTICAL 6CH INPUT CINEM
AUTO DETECT
ACTIV
COAXIAL ANALOG 96kHzfs DSP M
25
EN