Related Manuals for Barco G 6300
Summary of Contents for Barco G 6300
- Page 1 ARCO ROJECTION R/G 6300/6400 SIM6 NALYSER IT FOR ’ WNER ANUAL 01122003 R5976046/03...
- Page 2 Barco nv Intelligent Displays Noordlaan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51 E-mail: presentations.bid@barco.com Visit us at the web: www.barco.com Printed in Belgium...
- Page 3 Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
-
Page 5: Table Of Contents
Index........................11 R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... - Page 6 Table of contents R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003...
-
Page 7: Kit Description
Image 1-1 Type of analyzer handled in this manual 1.2 Kit content Overview Number Description R812776K Red analyzer R812777K Green analyzer R812778K Blue analyzer R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... -
Page 8: Domain Of Application
1. Kit description Some projector (RST version) are equipped with adapted analyzers, please contact Barco Always check the type of analyzer and the type of projector and make sure to order the right analyzer. 1.3 Domain of application Overview The analyzers handled in this manual are used in the following projectors. -
Page 9: Access To The Analyzers
4. Open both lens locks by pulling them backwards (support the lens with one hand). (image 2-3) 5. Take the lens out of the lens house. Image 2-2 Image 2-1 Image 2-3 R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... -
Page 10: Removing The Top Cover
3. Turn out the 3 screws connecting the Top Cover to the Projector Frame. (image 2-7) 4. Remove the Top Cover. 5. Reverse this procedure to reinstall the Top Cover. Image 2-5 Remove the Lens Cover R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... -
Page 11: Removing The Emc Plat
1. Loosen the screw B retaining the electrical conductor. (image 2-8) 2. Turn out the screws A retaining the little plate 3. Remove the little plate 4. Turn carefully the remaining screws out. (image 2-9) 5. Remove the EMC plate R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... - Page 12 2. Access to the analyzers Image 2-8 Image 2-9 be careful not to drop the screws into the projector. R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003...
-
Page 13: Replacing The Analyzers
5. Remove the analyzer by pulling it slightly laterally to free fixation holes and sliding it gently out of the assembly. One may use a screwdriver to pull out the analyzer (by putting it in the screwdriver opening) (image 3-4) Image 3-1 Image 3-2 Image 3-3 R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... -
Page 14: Mounting The Analyzers
How to mount the analyzers ? 1. To mount the analyzers proceed by reversing above procedure Always mount with the reference dots oriented towards the outside of the assembly (towards the LCD driver) R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003... -
Page 15: Index
Index INDEX access lens content mounting description removal domain replacement EMC plate Top Cover Removing introduction R5976046 ANALYSER KIT FOR R/G 6300/6400 AND SIM6 01122003...