Page 1 Description of Device Functions Proline Promass 83 MODBUS RS485 Coriolis Mass Flow Measuring System 0000 0001 0002 0003 0004 0005 0000 0001 0002 0003 0004 0005 0200 0200 0201 0201 0202 0203 0204 0205 0200 0201 0202 0203 0204 0205...
Page 2 Device Functions Proline Promass 83 MODBUS Endress+Hauser...
Page 3: Table Of Contents
7.2.3 Function group INFORMATION ..92 Function matrix Proline Promass 83 ... . 9 Group RELAY OUTPUT (1 to 2) ....93 7.3.1 Function group CONFIGURATION .
Page 4 Device Functions Proline Promass 83 MODBUS Block SPECIAL FUNCTION ..10.1 Group DENSITY FUNCTIONS ....125 10.1.1 Function group CONFIGURATION ..125 10.2 Group BATCHING FUNCTION .
Page 5: Using This Manual
Device Functions Proline Promass 83 MODBUS RS485 1 Using this Manual Using this Manual This manual must be used in conjunction with the Operating Instructions of the measuring device. A description of all the functions of the measuring device is provided here.
Page 6: Function Matrix
2 Function Matrix Device Functions Proline Promass 83 MODBUS RS485 Function Matrix General layout of the function matrix The function matrix consists of four levels: Blocks -> Groups -> Function groups -> Functions 0000 0001 0002 0003 0009 … 0400...
Page 7: Function Matrix
Device Functions Proline Promass 83 MODBUS RS485 2 Function Matrix 2.1.5 Codes identifying cells Each cell (block, group, function group and function) in the function matrix has an individual, unique code. Blocks: The code is a letter (A, B, C, etc.) Groups: The code consists of three letters (AAA, ABA, BAA, etc.).
Page 8: Illustration Of The Function Descriptions
2 Function Matrix Device Functions Proline Promass 83 MODBUS RS485 Illustration of the function descriptions UNIT LENGTH 0424 For selecting the unit for displaying the length of the nominal diameter. 2125 MODBUS register: The unit zou select here is also valid for:...
Page 9: Function Matrix Proline Promass 83
Device Functions Proline Promass 83 MODBUS RS485 2 Function Matrix Function matrix Proline Promass 83 Blocks Groups Function groups → → MEASURING VALUES see Page 11 MEASURED VARIABLES (see P. 10) → SYSTEM UNITS see Page 15 ↓↑ → →...
Page 10: Block Measured Variables
3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485 Block MEASURED VARIABLES ⇐ ⇐ ⇒ ⇒ ⇐ ⇐ ⇒ ⇒ Endress+Hauser...
Page 11: Group Measuring Values
Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES Group MEASURING VALUES 3.1.1 Function group MAIN VALUES MEASURED MEASURING VALUES MAIN VALUES → → VARIABLES Function description MEASURED VARIABLES → MEASURING VALUES → MAIN VALUES Note! • The engineering units of all the measured variables shown here can be set in the “SYSTEM UNITS” group.
Page 12: Function Group Additional Values
3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485 3.1.2 Function group ADDITIONAL VALUES MEASURED → → MEASURING VALUES MAIN VALUES VARIABLES ADDITIONAL VALUES Function description MEASURED VARIABLES → MEASURING VALUES → ADDITIONAL VALUES TARGET MASS 0020 Note!
Page 13 Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES Function description MEASURED VARIABLES → MEASURING VALUES → ADDITIONAL VALUES CARRIER MASS 0025 Note! FLOW Function is not available unless one of the following was selected: • in the function DENSITY FUNCTION (7000), see Page 125:...
Page 14 3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485 Function description MEASURED VARIABLES → MEASURING VALUES → ADDITIONAL VALUES % BLACK-LIQUOR 0030 Note! Function is not available unless %-BLACK LIQUOR was selected in the DENSITY MODBUS register: 2027 FUNCTION function (7000), (see Page 125).
Page 15: Group System Units
Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES Group SYSTEM UNITS 3.2.1 Function group CONFIGURATION MEASURED → MEASURING VALUES VARIABLES → SYSTEM UNITS CONFIGURATION Function description MEASURED VARIABLES → SYSTEM UNITS → CONFIGURATION You can select the units for measured variables in this function group.
Page 16 3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485 Function description MEASURED VARIABLES → SYSTEM UNITS → CONFIGURATION UNIT VOLUME 0402 For selecting the unit for displaying the volume flow (volume/time). FLOW The unit you select here is also valid for:...
Page 17 Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES Function description MEASURED VARIABLES → SYSTEM UNITS → CONFIGURATION UNIT CORRECTED 0404 For selecting the unit for displaying the corrected volume flow (corrected VOLUME FLOW volume/time). MODBUS register: 2105...
Page 18: Configuration
3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485 3.2.2 Function group ADDITIONAL CONFIGURATION MEASURED → MEASURING VALUES VARIABLES → SYSTEM UNITS CONFIGURATION ADDITIONAL CONFIGURATION Function description MEASURED VARIABLES → SYSTEM UNITS → ADDITIONAL CONFIGURATION UNIT DENSITY 0420 For selecting the unit for displaying the fluid density.
Page 19 Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES Function description MEASURED VARIABLES → SYSTEM UNITS → ADDITIONAL CONFIGURATION UNIT LENGTH 0424 For selecting the unit for displaying the length of the nominal diameter. MODBUS register: 2125 The unit you select here is also valid for:...
Page 20: Block Quick Setup
4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485 Block QUICK SETUP Group / Block Functions Function groups QS - PULS. QS - SETUP QS - COM- QUICK SETUP ⇒ ⇒ COMMISSION FLOW BATCHING GAS MEAS. MUNICATION (1002) P. 20 (1003) P.
Page 21 Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP Function description QUICK SETUP T-DAT SAVE/LOAD 1009 Use this function to save the parameter settings / configuration of the transmitter in a transmitter DAT (T-DAT), or to load the parameter settings from the T-DAT...
Page 22: Commissioning" Quick Setup Menu
4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485 “Commissioning” Quick Setup menu 1002 Quick Setup ENDRESS+HAUSER Commission 2000 Language HOME-POSITION Pre-setting Selection pre-settings Deliver Settings Actual Settings Selection system units Temperature Mass flow Volume flow Corr. Vol. flow...
Page 23 Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP Note! • The display returns to the cell SETUP COMMISSION (1002) if you press the X key combination during parameter interrogation. The stored parameters remain valid. • The “Commissioning” Quick Setup must be carried out before one of the Quick Setups explained below is run.
Page 24: Batching" Quick Setup Menu
Note! This function is only available when the additional “batching” software is installed in the measuring device (order option). You can order this software from Endress+Hauser as an accessory at a later date (see Operating Instructions). This Quick Setup guides the user systematically through all the device functions that have to be adjusted and configured for batching operation.
Page 25 Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP " Caution! The “Batching” Quick Setup sets certain device parameters for discontinuous measurement operation. If the measuring device is used for continuous flow measurement at a later time, we recommend at you rerun the “Commissioning”...
Page 26 4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485 Settings for the Batching Setup menu: Fct. code Function name Suggested settings Description Call up through the function matrix: QUICK SETUP QUICK SETUP BATCHING/DOSING see P. 20 1005 QUICK SETUP see P.
Page 27: Pulsating Flow" Quick Setup Menu
Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP “Pulsating flow” Quick Setup menu Note! The Quick Setup “Pulsating flow” is only available if the device has a current output or a pulse/frequency output. Certain types of pump such as reciprocating, peristaltic and cam-type pumps, for example, create a flow characterized by severe periodic fluctuations.
Page 28 4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485 Note! • The display returns to the cell SETUP PULSATING FLOW (1003) if you press the X key combination during parameter interrogation. • You can call up the Setup menu either directly from the “COMMISSIONING” Quick Setup menu or manually by means of the function QUICK SETUP PULSATING FLOW (1003).
Page 29: Gas Measurement" Quick Setup Menu
Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP “Gas measurement” Quick Setup menu XXX.XXX.XX HOME POSITION 1004 Quick Setup Setup Gas measurement 6400 Assign Low flow cut off 6402 On value Low flow cut off 6403 Off value...
Page 30: Communication" Quick Setup Menu
4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485 “Communication” Quick Setup menu To establish serial data transfer, various arrangements between the MODBUS master and MODBUS slave are required which have to be taken into consideration when configuring various functions.
Page 31: Data Back-Up/Transfer
Device Functions Proline Promass 83 MODBUS RS485 4 Block QUICK SETUP Data back-up/transfer You can use the T-DAT SAVE/LOAD function to transfer data (device parameters and settings) between the T-DAT (removable memory) and the EEPROM (device memory). This is required for the following applications: •...
Page 32: Block User Interface
5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Block USER INTERFACE ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ Endress+Hauser...
Page 33: Group Control
• If you press the O/S keys simultaneously at startup, the language defaults to “ENGLISH”. • You can change the language group via the configuration software FieldCare. Please do not hesitate to contact your Endress+Hauser sales office if you have any questions. Endress+Hauser...
Page 34 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → CONTROL → BASIC CONFIGURATION DISPLAY DAMPING 2002 For entering a time constant which defines how the display reacts to severely fluctuating flow variables, either very quickly (enter a low time constant) or with...
Page 35: Unlocking/Locking
HOME position. • You can also disable programming in this function by entering any number (other than the defined private code). • The Endress+Hauser service organization can be of assistance if you mislay your personal code. DEFINE PRIVATE...
Page 36: Function Group Operation
5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 5.1.3 Function group OPERATION → → USER INTERFACE CONTROL BASIC CONFIGURATION UNLOCKING/LOCKING OPERATION Function description USER INTERFACE → CONTROL → OPERATION TEST DISPLAY 2040 For testing the operability of the local display and its pixels.
Page 37: Group Main Line
Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Group MAIN LINE 5.2.1 Function group CONFIGURATION → USER INTERFACE CONTROL → MAIN LINE CONFIGURATION Function description USER INTERFACE → CONTROL → CONFIGURATION ASSIGN 2200 For assigning a value to be displayed to the main line (top line in the local display).
Page 38 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → CONTROL → CONFIGURATION ASSIGN 2200 Advanced selection: (with the optional SW package ADVANCED DIAGNOSIS) (continued) 79 = MASS FLOW DEVIATION 80 = DENSITY DEVIATION...
Page 39: Function Group Multiplex
Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE 5.2.2 Function group MULTIPLEX → USER INTERFACE CONTROL → MAIN LINE CONFIGURATION MULTIPLEX Function description USER INTERFACE → CONTROL → MULTIPLEX ASSIGN 2220 For assigning a second reading to be displayed in the main line alternately (every 10 seconds) with the value defined in the ASSIGN function (2200).
Page 40 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → CONTROL → MULTIPLEX ASSIGN 2220 Advanced selection: (with the optional SW package ADVANCED DIAGNOSIS) (continued) 79 = MASS FLOW DEVIATION 80 = DENSITY DEVIATION...
Page 41: Group Additional Line
Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Group ADDITIONAL LINE 5.3.1 Function group CONFIGURATION → USER INTERFACE CONTROL MAIN LINE → ADDITIONAL LINE CONFIGURATION Function description USER INTERFACE → ADDITIONAL LINE → CONFIGURATION ASSIGN 2400 For assigning a value to be displayed to the additional line (middle line in the local display).
Page 42 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → ADDITIONAL LINE → CONFIGURATION ASSIGN 2400 Advanced selection: with the optional SW package CONCENTRATION (continued) 61 = TARGET MASS FLOW 62 = % TARGET MASS FLOW...
Page 43 Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Function description USER INTERFACE → ADDITIONAL LINE → CONFIGURATION DISPLAY MODE 2403 Note! Function is not available unless one of the following was selected in the ASSIGN MODBUS register:...
Page 44: Function Group Multiplex
5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 5.3.2 Function group MULTIPLEX → USER INTERFACE CONTROL MAIN LINE → ADDITIONAL LINE CONFIGURATION MULTIPLEX Function description USER INTERFACE → ADDITIONAL LINE → MULTIPLEX ASSIGN 2420 For assigning a second reading to be displayed in the main line alternately (every 10 seconds) with the value defined in the ASSIGN function (2400).
Page 45 Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Function description USER INTERFACE → ADDITIONAL LINE → MULTIPLEX ASSIGN 2420 Advanced selection: with the optional SW package CONCENTRATION (continued) 61 = TARGET MASS FLOW 62 = % TARGET MASS FLOW...
Page 46 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → ADDITIONAL LINE → MULTIPLEX FORMAT 2422 For selecting the maximum number of places after the decimal point to be displayed for the display value.
Page 47: Group Information Line
Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Group INFORMATION LINE 5.4.1 Function group CONFIGURATION → USER INTERFACE CONTROL MAIN LINE ADDITIONAL LINE → INFORMATION LINE CONFIGURATION Function description USER INTERFACE → INFORMATION LINE → CONFIGURATION ASSIGN...
Page 48 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → INFORMATION LINE → CONFIGURATION ASSIGN 2600 Advanced selection: with the optional SW package CONCENTRATION (continued) 61 = TARGET MASS FLOW 62 = % TARGET MASS FLOW...
Page 49 Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Function description USER INTERFACE → INFORMATION LINE → CONFIGURATION DISPLAY MODE 2603 Note! Function is not available unless one of the following was selected in the ASSIGN MODBUS register:...
Page 50: Function Group Multiplex
5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 5.4.2 Function group MULTIPLEX → USER INTERFACE CONTROL MAIN LINE ADDITIONAL LINE → INFORMATION LINE CONFIGURATION MULTIPLEX Function description USER INTERFACE → INFORMATION LINE → MULTIPLEX Note! If you select the BATCHING OPERATING KEYS in the function ASSIGN (2600), the multiplex display functionality is not available in the information line.
Page 51: Endress+Hauser
Device Functions Proline Promass 83 MODBUS RS485 5 Block USER INTERFACE Function description USER INTERFACE → INFORMATION LINE → MULTIPLEX ASSIGN 2620 Advanced selection: with the optional SW package ADVANCED DIAGNOSIS (continued) 79 = MASS FLOW DEVIATION 80 = DENSITY DEVIATION...
Page 52 5 Block USER INTERFACE Device Functions Proline Promass 83 MODBUS RS485 Function description USER INTERFACE → INFORMATION LINE → MULTIPLEX DISPLAY MODE 2623 Note! Function is not available unless one of the following was selected in the ASSIGN MODBUS register:...
Page 53: Block Totalizer
Device Functions Proline Promass 83 MODBUS RS485 6 Block TOTALIZER Block TOTALIZER ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ Endress+Hauser...
Page 54: Group Totalizer (1 To 3)
6 Block TOTALIZER Device Functions Proline Promass 83 MODBUS RS485 Group TOTALIZER (1 to 3) 6.1.1 Function group CONFIGURATION → → TOTALIZER TOTALIZER 1 CONFIGURATION → TOTALIZER 2 CONFIGURATION → TOTALIZER 3 CONFIGURATION Function description TOTALIZER → TOTALIZER (1 to 3) → CONFIGURATION Note! The function descriptions below apply to totalizers 1 to 3;...
Page 55 Device Functions Proline Promass 83 MODBUS RS485 6 Block TOTALIZER Function description TOTALIZER → TOTALIZER (1 to 3) → CONFIGURATION TOTALIZER MODE 3002 For selecting how the totalizer should operate. MODBUS register: Options: Totalizer 1 2605 0 = BALANCE Totalizer 2 2805 Positive and negative flow components.
Page 56: Function Group Operation
6 Block TOTALIZER Device Functions Proline Promass 83 MODBUS RS485 6.1.2 Function group OPERATION → → TOTALIZER TOTALIZER 1 CONFIGURATION OPERATION → TOTALIZER 2 CONFIGURATION OPERATION → TOTALIZER 3 CONFIGURATION OPERATION Function description TOTALIZER → TOTALIZER (1 to 3) → OPERATION Note! The function descriptions below apply to totalizers 1 to 3;...
Page 57: Group Handling Totalizer
Device Functions Proline Promass 83 MODBUS RS485 6 Block TOTALIZER Group HANDLING TOTALIZER → TOTALIZER TOTALIZER 1 TOTALIZER 2 TOTALIZER 3 → HANDLING TOTALIZER Handling totalizer functions Function description TOTALIZER → HANDLING TOTALIZER → Handling totalizer functions RESET ALL 3800 Resets the totals and the overflows of all totalizers to zero.
Page 58: Block Outputs
7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Block OUTPUTS ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ Endress+Hauser...
Page 59: Group Current Output
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Group CURRENT OUTPUT 7.1.1 Function group CONFIGURATION → → OUTPUTS CURRENT OUTPUT 1 CONFIGURATION Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION ASSIGN CURRENT 4000 For assigning a measured variable to the current output.
Page 60 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION CURRENT SPAN 4001 For selecting the current span. The selection specifies the operational range and the lower and upper signal on alarm.
Page 61 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION VALUE 0_4 mA 4002 Use this function to assign the 0/4 mA current a value. The value can be higher or lower than the value assigned to 20 (function VALUE...
Page 62 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION VALUE 20 mA 4003 Use this function to assign the 20 mA current a value. The value can be higher or lower than the value assigned to 0/4 (function VALUE...
Page 63 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION MEASURING 4004 Description of the individual options: MODE STANDARD (continued) The current output signal is proportional to the measured variable. The flow components outside the scaled measuring range (defined by the 0_4 mA VALUE m and the 20 mA VALUE n) are taken into account as follows for signal output.
Page 64 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION Detailed explanations and How the current output responds at a defined measuring range m-n (see Fig. 17) and flow behavior (see Fig. 18): information ➀...
Page 65 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION Detailed explanations and How the current output responds at a defined measuring range m-n (see Fig. 22) and flow behavior (see Fig. 23): information (continued) ➀...
Page 66 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → CURRENT OUTPUT 1 → CONFIGURATION FAILSAFE MODE 4006 For safety reasons it is advisable to ensure that the current output assumes a predefined state in the event of a fault. The setting you select here affects only the...
Page 67: Function Group Operation
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS 7.1.2 Function group OPERATION → → OUTPUTS CURRENT OUTPUT 1 CONFIGURATION OPERATION Function description OUTPUTS → CURRENT OUTPUT 1 → OPERATION ACTUAL CURRENT 4040 Use this function to view the computed actual value of the output current.
Page 68: Group Pulse/Frequency Output 1
7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Group PULSE/FREQUENCY OUTPUT 1 7.2.1 Function group CONFIGURATION → OUTPUTS CURRENT OUTPUT 1 → PULSE/FREQ. OUTPUT 1 ECA CONFIGURATION Function description OUTPUTS→PULSE/FREQUENCY OUTPUT 1→CONFIGURATION OPERATION MODE 4200 Configuration of the output as a pulse, frequency or status output.
Page 69 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) ASSIGN 4201 Note! FREQUENCY Function is not available unless the FREQUENCY setting was selected in the OPERATION MODE function (4200).
Page 70 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) END VALUE 4203 Note! FREQUENCY Function is not available unless the FREQUENCY setting was selected in the 3205 OPERATION MODE function (4200).
Page 71 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) VALUE F HIGH 4205 Note! Function is not available unless the FREQUENCY setting was selected in the MODBUS register: 3209 OPERATION MODE function (4200).
Page 72 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) Parameter setting examples for Parameter setting example 1: VALUE F LOW (4204) = not equal to zero flow (e.g. −5 m...
Page 73 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) MEASURING 4206 Note! MODE Function is not available unless the FREQUENCY setting was selected in the OPERATION MODE function (4200).
Page 74 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) MEASURING 4206 PULSATING FLOW MODE • If flow is characterized by severe fluctuations as is the case, for example, with...
Page 75 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) OUTPUT SIGNAL 4207 Note! Function is not available unless the FREQUENCY setting was selected in the MODBUS register: 3212 OPERATION MODE function (4200).
Page 76 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) OUTPUT SIGNAL 4207 In the operating status (flow present), the output signal level changes from 0 V to (continued) a positive voltage level.
Page 77 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) OUTPUT SIGNAL 4207 Example for active output circuit (ACTIVE): (continued) With an active circuit, the internal power supply is 24 V.
Page 78 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (FREQUENCY) TIME CONSTANT 4208 Note! Function is not available unless the FREQUENCY setting was selected in the MODBUS register: 3213 OPERATION MODE function (4200).
Page 79 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) ASSIGN PULSE 4221 Note! Function is not available unless the PULSE setting was selected in the MODBUS register: 3223 OPERATION MODE function (4200).
Page 80 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) PULSE WIDTH 4223 Note! (continued) When entering the pulse width, select a value that can still be processed by an external totalizer (e.g.
Page 81 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) OUTPUT SIGNAL 4226 Note! Function is not available unless the PULSE setting was selected in the MODBUS register: 3229 OPERATION MODE (4200) function.
Page 82 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) OUTPUT SIGNAL 4226 In the operating status (flow present), the output signal level changes from 0 V to (continued) a positive voltage level.
Page 83: Proline Promass
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) OUTPUT SIGNAL 4226 Example for active output circuit (ACTIVE): (continued) With an active circuit, the internal power supply is 24 V.
Page 84 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (PULSE) FAILSAFE MODE 4227 Note! Function is not available unless the PULSE setting was selected in the MODBUS register: 3230 OPERATION MODE function (4200).
Page 85 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (STATUS) ASSIGN STATUS 4241 Note! Function is not available unless the STATUS setting was selected in the MODBUS register: 3236 OPERATION MODE function (4200).
Page 86 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (STATUS) ON-VALUE 4242 Note! Function is not available unless STATUS was selected in the OPERATION MODE MODBUS register: 3237 function (4200) and LIMIT VALUE or FLOW DIRECTION was selected in the...
Page 87 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (STATUS) OFF-VALUE 4244 Note! Function is not available unless STATUS was selected in the OPERATION MODE MODBUS register: 3241 function (4200) and a LIMIT VALUE was selected in the ASSIGN STATUS...
Page 88 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → CONFIGURATION (STATUS) MEASURING 4246 Note! MODE Function is not available unless STATUS was selected in the OPERATION MODE function (4200) and the status output was assigned a limit value.
Page 89: Function Group Operation
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS 7.2.2 Function group OPERATION → OUTPUTS CURRENT OUTPUT 1 → PULSE/FREQ. OUTPUT 1 ECA CONFIGURATION OPERATION Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → OPERATION (FREQUENCY) ACTUAL 4301 Note! FREQUENCY...
Page 90 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → OPERATION (PULSE) SIMULATION 4322 Note! PULSE Function is not available unless the PULSE setting was selected in the OPERATION MODE function (4200).
Page 91 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → PULSE/FREQUENCY OUTPUT 1 → OPERATION (STATUS) ACTUAL STATUS 4341 Note! Function is not available unless the STATUS setting was selected in the MODBUS register: 3248 OPERATION MODE function (4200).
Page 92: Function Group Information
7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 7.2.3 Function group INFORMATION → OUTPUTS CURRENT OUTPUT 1 → PULSE/FREQ. OUTPUT 1 ECA CONFIGURATION OPERATION INFORMATION Function description OUTPUTS→PULSE/FREQUENCY OUTPUT 1→INFORMATION TERMINAL 4380 Use this function to view the numbers of the terminals (in the connection NUMBER compartment) and the polarity used by the pulse/frequency output.
Page 93: Group Relay Output (1 To 2)
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Group RELAY OUTPUT (1 to 2) 7.3.1 Function group CONFIGURATION → OUTPUTS CURRENT OUTPUT 1 PULSE/FREQ. OUTPUT 1 ECA → RELAY OUTPUT 1 CONFIGURATION → RELAY OUTPUT 2 CONFIGURATION Function description OUTPUTS →...
Page 94 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → RELAY OUTPUT (1 to 2) → CONFIGURATION ASSIGN RELAY 4700 Advanced selection: with the optional SW package ADVANCED DIAGNOSIS (continued) 84 = LIMIT MASS FLOW DEVIATION...
Page 95 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Function description OUTPUTS → RELAY OUTPUT (1 to 2) → CONFIGURATION OFF-VALUE 4703 Note! Function is not available unless LIMIT VALUE was selected in the ASSIGN RELAY MODBUS register: function (4700).
Page 96 7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 Function description OUTPUTS → RELAY OUTPUT (1 to 2) → CONFIGURATION MEASURING 4705 Note! MODE This function is not visible unless a limit value was assigned to the relay output.
Page 97: Function Group Operation
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS 7.3.2 Function group OPERATION → OUTPUTS CURRENT OUTPUT 1 PULSE/FREQ. OUTPUT 1 ECA → RELAY OUTPUT 1 CONFIGURATION OPERATION → RELAY OUTPUT 2 CONFIGURATION OPERATION Function description OUTPUTS → RELAY OUTPUT (1 to 2) → OPERATION...
Page 98: Function Group Information
7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 7.3.3 Function group INFORMATION → OUTPUTS CURRENT OUTPUT 1 PULSE/FREQ. OUTPUT 1 ECA → RELAY OUTPUT 1 CONFIGURATION OPERATION INFORMATION → RELAY OUTPUT 2 CONFIGURATION OPERATION INFORMATION Function description OUTPUTS → RELAY OUTPUT (1 to 2) → INFORMATION...
Page 99: Information On The Response Of The Relay Output
Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS 7.3.4 Information on the response of the relay output General If you have configured the relay output signal for “LIMIT VALUE” or “FLOW DIRECTION”, you can define the requisite switch points in the ON-VALUE and OFF-VALUE functions. When the measured variable in question reaches one of these predefined values, the relay output switches as shown in the illustrations below.
Page 100: Switching Response Of The Relay Output
7 Block OUTPUTS Device Functions Proline Promass 83 MODBUS RS485 7.3.5 Switching response of the relay output Contact* Function State Relay coil ON (operation) System in measuring mode XXX.XXX.XX energized A0001239 A0001237 System not in measuring mode (power supply failed) XXX.XXX.XX...
Page 101 Device Functions Proline Promass 83 MODBUS RS485 7 Block OUTPUTS Contact* Function State Relay coil Flow direction forward energized A0001241 A0001239 A0001237 reverse energized A0001242 A0001240 A0001238 Limit value Limit value not overshot or – Mass flow undershot – Volume flow energized –...
Page 102: Block Inputs
8 Block INPUTS Device Functions Proline Promass 83 MODBUS RS485 Block INPUTS ⇐ ⇐ ⇒ ⇒ Endress+Hauser...
Page 103: Group Status Input
Device Functions Proline Promass 83 MODBUS RS485 8 Block INPUTS Group STATUS INPUT 8.1.1 Function group CONFIGURATION → → INPUTS STATUS INPUT CONFIGURATION Function description INPUTS → STATUS INPUT → CONFIGURATION ASSIGN STATUS 5000 Use this function to assign a switching function to the status input.
Page 104: Function Group Operation
8 Block INPUTS Device Functions Proline Promass 83 MODBUS RS485 8.1.2 Function group OPERATION → → INPUTS STATUS INPUT CONFIGURATION OPERATION Function description INPUTS → STATUS INPUT → OPERATION ACTUAL STATUS 5040 Use this function to view the current level of the status input.
Page 105: Function Group Information
Device Functions Proline Promass 83 MODBUS RS485 8 Block INPUTS 8.1.3 Function group INFORMATION → → INPUTS STATUS INPUT CONFIGURATION OPERATION INFORMATION Function description INPUTS → STATUS INPUT → INFORMATION TERMINAL 5080 Use this function to view the numbers of the terminals (in the connection NUMBER compartment) and the polarity used by the status input.
Page 106: Block Basic Function
9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Block BASIC FUNCTION ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ Endress+Hauser...
Page 107: Group Modbus Rs485
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION Group MODBUS RS485 9.1.1 Function group CONFIGURATION → → BASIC FUNCTION MODBUS RS485 CONFIGURATION Function description BASIC FUNCTION → MODBUS RS485 → CONFIGURATION TAG NAME 6300 For entering a tag name for the measuring device. You can edit and read this tag name via the local display or the MODBUS RS485 protocol.
Page 108 9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description BASIC FUNCTION → MODBUS RS485 → CONFIGURATION BYTE ORDER 6305 For selecting the byte transmission sequence for the Integer, Float and String data types. MODBUS register: 4915...
Page 109: Group Process Parameter
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION Group PROCESS PARAMETER 9.2.1 Function group CONFIGURATION → BASIC FUNCTION MODBUS RS485 → PROCESS PARAMETER CONFIGURATION Function description BASIC FUNCTION → PROCESS PARAMETER → CONFIGURATION ASSIGN LOW 6400 Use this function to assign the switch point for low flow cut off rate suppression.
Page 110 9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description BASIC FUNCTION → PROCESS PARAMETER → CONFIGURATION PRESSURE SHOCK 6404 The closure of a valve can cause brief but severe movements of the fluid in the SUPPRESSION piping system, movements which the measuring system registers.
Page 111: Function Group Epd Parameter
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION 9.2.2 Function group EPD PARAMETER → BASIC FUNCTION MODBUS RS485 → PROCESS PARAMETER CONFIGURATION EPD PARAMETER Function description BASIC FUNCTION → PROCESS PARAMETER → EPD PARAMETER EMPTY PIPE 6420 Use this function to activate the empty pipe detection (EPD).
Page 112 9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description BASIC FUNCTION → PROCESS PARAMETER → EPD PARAMETER EPD EXCITING 6426 Empty pipe detection (EPD) can be switched on in this function. CURRENT MAX In the event of inhomogeneous fluids or air bubbles, the exciting current of the...
Page 113: Function Group
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION 9.2.3 Function group REFERENCE PARAMETER → BASIC FUNCTION MODBUS RS485 → PROCESS PARAMETER CONFIGURATION EPD PARAMETER REFERENCE PARAMETER 646 Function description BASIC FUNCTION → PROCESS PARAMETER → REFERENCE PARAMETER...
Page 114 9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description BASIC FUNCTION → PROCESS PARAMETER → REFERENCE PARAMETER REFERENCE 6464 Note! TEMPERATURE Function is not available unless the CALCULATED REFERENCE DENSITY setting was selected in the CORRECTED VOLUME CALCULATION function (6460).
Page 115: Function Group Adjustment
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION 9.2.4 Function group ADJUSTMENT → BASIC FUNCTION MODBUS RS485 → PROCESS PARAMETER CONFIGURATION EPD PARAMETER REFERENCE PARAMETER 646 ADJUSTMENT Function description BASIC FUNCTION → PROCESS PARAMETER → ADJUSTMENT ZERO POINT 6480 This function enables a zero point adjustment to be automatically carried out.
Page 116 9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description BASIC FUNCTION → PROCESS PARAMETER → ADJUSTMENT DENSITY 6485 Use this function to enter the density setpoint value for the second fluid for which SETPOINT you want to carry out field density adjustment.
Page 117: Function Group
Device Functions Proline Promass 83 MODBUS RS485 9 Block BASIC FUNCTION 9.2.5 Function group PRESSURE CORRECTION → BASIC FUNCTION MODBUS RS485 → PROCESS PARAMETER CONFIGURATION EPD PARAMETER REFERENCE PARAMETER 646 ADJUSTMENT PRESSURE CORRECTION Function description BASIC FUNCTION → PROCESS PARAMETER → PRESSURE CORRECTION...
Page 118: Group System Parameter
9 Block BASIC FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Group SYSTEM PARAMETER 9.3.1 Function group CONFIGURATION → BASIC FUNCTION MODBUS RS485 PROCESS PARAMETER → SYSTEM PARAMETER CONFIGURATION Function description BASIC FUNCTION → SYSTEM PARAMETER → CONFIGURATION INSTALLATION 6600 Use this function to reverse the sign of the flow direction, if necessary.
Page 119: Group Sensor Data
For this reason, the functions described below cannot be changed even when you enter your personal code. Contact the Endress+Hauser service organization if you have any questions about these functions. Note! The individual values of the functions are also provided on the sensor nameplate.
Page 120: Function Group Flow Coefficient
BASIC FUNCTION → SENSOR DATA → FLOW COEFFICIENT All flow coefficients are set at the factory. All the sensor's parameter settings are saved on the S-DAT memory chip. Contact the Endress+Hauser service organization if you have any questions about these functions. TEMPERATURE 6840 This function shows the temperature coefficient KM.
Page 121: Function Group Density Coefficient
BASIC FUNCTION → SENSOR DATA → DENSITY COEFFICIENT All density coefficients are set at the factory. All the sensor's parameter settings are saved on the S-DAT memory chip. Contact the Endress+Hauser service organization if you have any questions about these functions. DENSITY 6850 This function shows the actual density coefficient C 0.
Page 122: Function Group
" Caution! These functions are used for displaying device parameters only and consequently cannot be accessed. Contact the Endress+Hauser service organization if you have any questions about these functions. MINIMAL 6860 The lowest fluid temperature measured appears on the display.
Page 123: Block Special Function
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Block SPECIAL FUNCTION ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒...
Page 124 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 ⇒ ⇒ ⇒ ⇐ ⇐ ⇐ Endress+Hauser...
Page 125: Group Density Functions
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.1 Group DENSITY FUNCTIONS 10.1.1 Function group CONFIGURATION → → SPECIAL FUNCTION H DENSITY FUNCTIONS CONFIGURATION Function description SPECIAL FUNCTION → DENSITY FUNCTIONS → CONFIGURATION DENSITY 7000 For selecting the density function which is used to calculate special density values FUNCTION or the percentage proportion of components in two-phase fluids.
Page 126 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → DENSITY FUNCTIONS → CONFIGURATION EXPANSION 7003 Note! COEFFICIENT Function is not available unless % MASS / % VOLUME or % BLACK-LIQUOR was SQUARE CARRIER selected in the DENSITY FUNCTION function (7000).
Page 127 Factory setting: % MASS 3D Note! If the relation between concentration density and temperature is given as table, the equation coefficients can be determined by Endress+Hauser e.g. via a coeffi- cient calculation program and transmitted to the measuring device. Endress+Hauser...
Page 128 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → DENSITY FUNCTIONS → CONFIGURATION CONCENTRATION 7022 For selecting the concentration specification. There are four different SELECTOR specifications available, via which various concentrations can be defined.
Page 129 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → DENSITY FUNCTIONS → CONFIGURATION COEFFICIENT A2 7034 Coefficient A2 entry. MODBUS register: See Note User input: 5-digit floating-point number Data type: Float Factory setting: 0...
Page 130 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → DENSITY FUNCTIONS → CONFIGURATION COEFFICIENT B2 7038 Note! This function does only appear if the option % MASS 3D, % VOLUME 3D or MODBUS register: See Note OTHER 3D was selected in the function MODE (7021).
Page 131: Group Batching Function
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.2 Group BATCHING FUNCTION 10.2.1 Function group CONFIGURATION → SPECIAL FUNCTION H DENSITY FUNCTIONS → BATCHING FUNCTION CONFIGURATION Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION BATCH SELECTOR 7200 For selecting the batching specification.
Page 132 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION ASSIGN BATCH 7202 Use this function to assign a batching variable to the batching specification. VARIABLE Options: MODBUS register: See Note...
Page 133 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION 7204 Use this function to specify a positive or negative compensation quantity. The COMPENSATION compensation quantity balances out a constant, system-related incorrect QUANTITY quantity.
Page 134 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION COMPENSATION 7205 • Response when MODE 1 is selected: MODE For short batchings and for batching cycles that follow on quickly from one (continued) other.
Page 135 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION CALCULATION 7206 Note! MODE Function is only available if MODE 1 or MODE 2 is selected in the function COMPENSATION MODE (7205).
Page 136 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION AVERAGING DRIP 7207 Note! Function is only available if MODE 1 or MODE 2 is selected in the function MODBUS register: See Note COMPENSATION MODE (7205).
Page 137 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → CONFIGURATION INPUT FORMAT 7209 Use this function to define the entry format of the quantities for the switch points of the valves.
Page 138: Function Group Valve Parameter
10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 10.2.2 Function group VALVE PARAMETER → SPECIAL FUNCTION H DENSITY FUNCTIONS → BATCHING FUNCTION CONFIGURATION VALVE PARAMETER Function description SPECIAL FUNCTION → BATCHING FUNCTION → VALVE PARAMETER The parameters for the switching contacts of up to 2 valves can be set in the following functions. The number of switching contacts (valves) available, and thus their settings in this group, is defined in the function BATCH STAGES (7208).
Page 139 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → VALVE PARAMETER OPEN VALVE 2 7222 For specifying the quantity value at which contact 2 opens. This is used as a switch point for valve 2 to output via an assigned output. The...
Page 140: Examples Of Setting Parameters For Batching Processes
10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → BATCHING FUNCTION → VALVE PARAMETER CLOSE VALVE 2 7223 For specifying the quantity value at which contact 2 closes. This is used as a switch point for valve 2 to output via an assigned output. The...
Page 141 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION ➁ ➂ ➃ ➀ A0004670 Fig. 37 : Example 1 v = Flow velocity [m/s] t = Time = Valve 1 open = Valve 2 open m = Start batching/coarse batching, valves 1 (7220) and 2 (7222) open...
Page 142 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Example 2 The second example explains the parameter settings of the various functions for batching with the entry format in % for the switch points of the valves. The following batching is to take place: •...
Page 143: Function Group Supervision
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.2.4 Function group SUPERVISION → SPECIAL FUNCTION H DENSITY FUNCTIONS → BATCHING FUNCTION CONFIGURATION VALVE PARAMETER SUPERVISION Function description SPECIAL FUNCTION → BATCHING FUNCTION → SUPERVISION MAXIMUM 7240 For specifying a maximum batching time. All valves close once the specified...
Page 144 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → BATCHING FUNCTION → SUPERVISION MINIMUM 7241 " BATCHING Caution! QUANTITY • When the batching quantity is adjusted (reduced/increased), (see function (continued) BATCH QUANTITY (7203) on Page 132) there is no automatic adjustment, i.e.
Page 145 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → SUPERVISION PROGRESS NOTE 7243 For specifying the batching quantity at which a message should be generated. When the specified batching quantity is achieved, the message is generated and...
Page 146: Function Group Operation
10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 10.2.5 Function group OPERATION → SPECIAL FUNCTION H DENSITY FUNCTIONS → BATCHING FUNCTION CONFIGURATION VALVE PARAMETER SUPERVISION OPERATION Function description SPECIAL FUNCTION → BATCHING FUNCTION → OPERATION BATCH 7260 For controlling the batching process.
Page 147 Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION Function description SPECIAL FUNCTION → BATCHING FUNCTION → OPERATION BATCH COUNTER 7263 Displays the number of batchings carried out. MODBUS register: 6397 Display: max. 7-digit floating-point number Data type:...
Page 148: Function Group Information
10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 10.2.6 Function group INFORMATION → SPECIAL FUNCTION H DENSITY FUNCTIONS → BATCHING FUNCTION CONFIGURATION VALVE PARAMETER SUPERVISION OPERATION INFORMATION Function description SPECIAL FUNCTION → BATCHING FUNCTION → INFORMATION VALVE 1...
Page 149: Group Advanced Diagnostics
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3 Group ADVANCED DIAGNOSTICS 10.3.1 Function group CONFIGURATION → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION ADVANCED CONFIGURATION → DIAGNOSTICS Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → CONFIGURATION...
Page 150: Function Group Acquisition
10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 10.3.2 Function group ACQUISITION → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → ACQUISITION ACQUISITION 7410...
Page 151: Function Group Mass Flow
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.3 Function group MASS FLOW → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → MASS FLOW Note! The appropriate unit is taken from the function UNIT MASS FLOW (0400), (see Page 15).
Page 152 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → MASS FLOW WARNING LEVEL 7426 Note! Function is not available unless ON was selected in the WARNING MODE MODBUS register: 6533 function (7403).
Page 153: Function Group Density
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.4 Function group DENSITY → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW DENSITY Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → DENSITY Note! The appropriate unit is taken from the function UNIT DENSITY (0420), (see Page 18).
Page 154 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → DENSITY ACTUAL 7435 This function displays the deviation between the measured density and the DEVIATION reference values (FACTORY or USER), see Page 149, selected in the function SELECT REFERENCE CONDITION (7402).
Page 155: Function Group Reference Density
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.5 Function group REFERENCE DENSITY → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW DENSITY REFERENCE DENSITY Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → REFERENCE DENSITY Note! The appropriate unit is taken from the function UNIT REFERENCE DENSITY (0421) ( Page 18).
Page 156 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → REFERENCE DENSITY HISTORY 7444 The last ten reference density values since the saved values were last reset appear REFERENCE on the display.
Page 157: Function Group Temperature
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.6 Function group TEMPERATURE → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW DENSITY REFERENCE DENSITY TEMPERATURE Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → TEMPERATURE Note! The appropriate unit is taken from the function UNIT TEMPERATURE (0422), (see Page 18).
Page 158 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → TEMPERATURE HISTORY 7454 The last ten temperature values since the saved values were last reset appear on TEMPERATURE the display. MODBUS register:...
Page 159: Function Group Tube Damping
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.7 Function group TUBE DAMPING → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW DENSITY REFERENCE DENSITY TEMPERATURE TUBE DAMPING Function description SPECIAL FUNCTION →...
Page 160 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → TUBE DAMPING HISTORY TUBE 7464 The last ten tube damping values since the saved values were last reset appears on DAMPING the display.
Page 161: Function Group Electrodynamic Sensors
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.8 Function group ELECTRODYNAMIC SENSORS → SPECIAL FUNCTION H DENSITY FUNCTIONS BATCHING FUNCTION → ADVANCED DIAGNOSTICS HEA CONFIGURATION ACQUISITION MASS FLOW DENSITY REFERENCE DENSITY TEMPERATURE TUBE DAMPING ELECTRODYNAMIC SENSORS Function description SPECIAL FUNCTION →...
Page 162 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → ELECTRODYNAMIC SENSORS HISTORY ELECTR. 7474 The last ten values of the electrodynamic sensors since the saved values were last SENSORS reset appear on the display.
Page 163: Function Group Operating Frequency Fluctuation
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.9 Function group OPERATING FREQUENCY FLUCTUATION → SPECIAL FUNCTION H DENSITY FUNCTIONS ↓ BATCHING FUNCTION ↓ → ADVANCED DIAGNOSTICS HEA CONFIGURATION ↓ ACQUISITION ↓ MASS FLOW ↓ DENSITY ↓...
Page 164 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → FREQU. FLUCTUATION HISTORY 7484 The last ten values of the operating frequency fluctuation since the saved values OPERATING were last reset appear on the display.
Page 165: Fluctuation
Device Functions Proline Promass 83 MODBUS RS485 10 Block SPECIAL FUNCTION 10.3.10 Function group TUBE DAMPING FLUCTUATION → SPECIAL FUNCTION H DENSITY FUNCTIONS ↓ BATCHING FUNCTION ↓ → ADVANCED DIAGNOSTICS HEA CONFIGURATION ↓ ACQUISITION ↓ MASS FLOW ↓ DENSITY ↓...
Page 166 10 Block SPECIAL FUNCTION Device Functions Proline Promass 83 MODBUS RS485 Function description SPECIAL FUNCTION → ADVANCED DIAGNOSTICS → TUBE DAMP. FLUCT. MAXIMUM VALUE 7493 The highest value of the tube damping fluctuation since the saved values were last reset appears on the display.
Page 167: Block Supervision
Device Functions Proline Promass 83 MODBUS RS485 11 Block SUPERVISION Block SUPERVISION ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇐ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇐ ⇐ ⇒ ⇒ Endress+Hauser...
Page 168: Group System
11 Block SUPERVISION Device Functions Proline Promass 83 MODBUS RS485 11.1 Group SYSTEM 11.1.1 Function group CONFIGURATION → → SUPERVISION SYSTEM CONFIGURATION Function description SUPERVISION → SYSTEM → CONFIGURATION ALARM DELAY 8005 For entering a time span for which the criteria for an error have to be satisfied without interruption before a fault or notice message is generated.
Page 169: Function Group Operation
Device Functions Proline Promass 83 MODBUS RS485 11 Block SUPERVISION 11.1.2 Function group OPERATION → → SUPERVISION SYSTEM CONFIGURATION OPERATION Function description SUPERVISION → SYSTEM → OPERATION ACTUAL SYSTEM 8040 Displays the present system condition. CONDITION Display: MODBUS register: 6859 1 = “SYSTEM OK”...
Page 170: Mass Flow
11 Block SUPERVISION Device Functions Proline Promass 83 MODBUS RS485 Function description SUPERVISION → SYSTEM → OPERATION SIMULATION 8043 Use this function to set all inputs, outputs and totalizers to their defined flow- MEASURAND response modes, in order to check whether they respond correctly. During this time, the message “SIMULATION MEASURAND”...
Page 171: Group Version Info
Device Functions Proline Promass 83 MODBUS RS485 11 Block SUPERVISION 11.2 Group VERSION INFO 11.2.1 Function group DEVICE → SUPERVISION SYSTEM → VERSION INFO DEVICE Function description SUPERVISION → VERSION INFO → DEVICE DEVICE 8100 Displays the current device software version.
Page 172: Function Group Sensor
11 Block SUPERVISION Device Functions Proline Promass 83 MODBUS RS485 11.2.2 Function group SENSOR → SUPERVISION SYSTEM → VERSION INFO DEVICE SENSOR Function description SUPERVISION → VERSION INFO → SENSOR SERIAL NUMBER 8200 Use this function to view the serial number of the sensor.
Page 173: Function Group Amplifier
• The language options of the available language group are displayed in the LANGUAGE (2000) function. • You can change the language group via the configuration software FieldCare. Please do not hesitate to contact your Endress+Hauser sales office if you have any questions. Endress+Hauser...
Page 174: Function Group F-Chip
11 Block SUPERVISION Device Functions Proline Promass 83 MODBUS RS485 11.2.4 Function group F-CHIP → SUPERVISION SYSTEM → VERSION INFO DEVICE SENSOR AMPLIFIER F-CHIP Function description SUPERVISION → VERSION INFO → F-CHIP STATUS F-CHIP 8240 Use this function to check whether an F-CHIP is installed and which software options are available.
Page 175: Function Group I/O Module
Device Functions Proline Promass 83 MODBUS RS485 11 Block SUPERVISION 11.2.5 Function group I/O MODULE → SUPERVISION SYSTEM → VERSION INFO DEVICE SENSOR AMPLIFIER F-CHIP I/O MODULE Function description SUPERVISION → VERSION INFO → I/O MODULE I/O MODULE TYPE 8300 Displays the configuration of the I/O module.
Page 176: Function Groups I/O Submodule 2 To 4
11 Block SUPERVISION Device Functions Proline Promass 83 MODBUS RS485 11.2.6 Function groups I/O SUBMODULE 2 to 4 → SUPERVISION SYSTEM → VERSION INFO DEVICE SENSOR AMPLIFIER F-CHIP I/O MODULE I/O SUBMODULE 2 I/O SUBMODULE 3 I/O SUBMODULE 4 Function description SUPERVISION →...
Page 177 Device Functions Proline Promass 83 MODBUS RS485 11 Block SUPERVISION Function description SUPERVISION → VERSION INFO → I/O SUBMODULE 2 to 4 SOFTWARE 8383 Use this function to view the software revision number of the corresponding REVISION NUMBER submodule. SUB IN-/OUTPUT...
Page 178: Factory Settings
12 Factory settings Device Functions Proline Promass 83 MODBUS RS485 Factory settings 12.1 SI units (not for USA and Canada) 12.1.1 Low flow cut off, full scale value, pulse value – Liquid Nominal diam. Low flow cut off Full scale value...
Page 179: Language
Device Functions Proline Promass 83 MODBUS RS485 12 Factory settings 12.1.3 Language Country Language Country Language Australia English Malaysia English Belgium English Norway Norsk China Chinese Poland Polish Denmark English Portugal Portuguese Germany Deutsch Austria Deutsch England English Russia Russian...
Page 180: Us Units (Only For Usa And Canada)
12 Factory settings Device Functions Proline Promass 83 MODBUS RS485 12.2 US units (only for USA and Canada) 12.2.1 Low flow cut off, full scale value, pulse value – Liquid Nominal diam. Low flow cut off Full scale value Pulse value [mm] (approx.
Page 181: Index Function Matrix
Device Functions Proline Promass 83 MODBUS Index function matrix Index function matrix Blocks 430 = OPERATION ......89 438 = INFORMATION .
Page 182 Index function matrix Device Functions Proline Promass 83 MODBUS 0022 = TARGET VOLUME FLOW ....12 2602 = FORMAT .......48 0023 = % TARGET VOLUME FLOW .
Page 183 Device Functions Proline Promass 83 MODBUS Index function matrix Functions 5... 6854 = DENSITY COEFFICIENT C 4 ....121 6855 = DENSITY COEFFICIENT C 5 ....121 5000 = ASSIGN STATUS INPUT .
Page 184 Index function matrix Device Functions Proline Promass 83 MODBUS 7403 = WARNING MODE ..... . . 149 7495 = ACTUAL DEVIATION .....166 7410 = ACQUISITION MODE .
Page 185: Index Key Words
Device Functions Proline Promass 83 MODBUS Index key words Index key words Status (pulse/freq. output) ..... . 85 Totalizer ....... . 54, 57 Access type .
Page 186 Index key words Device Functions Proline Promass 83 MODBUS A3 ........129 Density .
Page 187 Device Functions Proline Promass 83 MODBUS Index key words Totalizer ........57 Status input .
Page 188 Index key words Device Functions Proline Promass 83 MODBUS Sensor data ....... . 119 On value .
Page 189 Device Functions Proline Promass 83 MODBUS Index key words MODBUS register ....... 8 Value .
Page 190 Index key words Device Functions Proline Promass 83 MODBUS Reference Temperature ..... . 114, 127 Switch point ....... . .91 Reference value Special function .
Page 191 Device Functions Proline Promass 83 MODBUS Index key words KM ........120 Value F high .
Page 192 www.endress.com/worldwide BA108D/06/en/11.08 71085231 FM+SGML6.0...

Endress+Hauser Proline Promass 83 Function Manual

1 Using this Manual

2 Function Matrix

3 Block MEASURED VARIABLES

4 Block QUICK SETUP

5 Block USER INTERFACE

Block TOTALIZER

Block OUTPUTS

Block INPUTS

9 Block BASIC FUNCTION

10 Block SPECIAL FUNCTION

11 Block SUPERVISION

12 Factory Settings

Index Function Matrix

Index Key Words

Quick Links

Related Manuals for Endress+Hauser Proline Promass 83

Summary of Contents for Endress+Hauser Proline Promass 83

Table of Contents