Caution This device is registered as an EMC for commercial purposes. Vendors and users should be aware of this EMC registration. If this device is sold or purchased by mistake, the device will need to be altered for domestic use. FCC Compliance Statement Caution : Any changes or modifications in the construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the...
Page 3
4. The SVR-1630 can be damaged by physical shock because it contains an HDD. Therefore, do not throw or drop the device. 5. The SVR-1630 is made of metal. If it is thrown at anybody it may cause harm. Install the device in a safe place out of the reach of children.
SVR-1630 Contents Contents Executive Summary ......................... 7 Main Features of the SVR-1630..................... 7 Component Check........................8 Description of the Front/Rear View ..................10 Installation and Connection......................12 Basic Connection and Start-up..................... 12 Overall Layout ........................ 12 Connecting a Camera....................13 Connecting a Monitor ....................
Page 5
Contents SVR-1630 8.2.4 Time Format ......................26 8.2.5 Date Mode ......................26 8.2.6 Time......................... 26 8.2.7 Apply Date/Time ..................... 26 Setting Recording Conditions ..................26 8.3.1 Configuration Status....................27 8.3.2 Channel Status ....................... 27 8.3.3 Record Rate/Quality....................28 8.3.4 Rate (fps) ........................ 28 8.3.5...
Page 6
Remote Monitoring and Control..................48 11.1 Connecting via Ethernet ....................48 11.2 Configuring an SVR-1630 Network ................49 Using the SVR Manager ....................50 12.1 PC System Requirements for running the SVR Manager........... 50 12.2 Installing the SVR Manager ..................50 12.3 Uninstalling the SVR Manager..................
Executive Summary 1. Main Features of the SVR-1630 The SVR-1630 is a new concept DVR, saving the video inputs, audio, text data and alarm data of 16 channels in two built-in HDDs, with its main features described below. □ 16-Channel Video Input Support □...
Executive Summary 2. Component Check Please check the package to make sure that you receive all the accessories, including the components shown below. 1. SVR-1630 (1EA) 2. AC Power Cord (1EA) 3. CD-ROM (Including SVR Manager) (1EA) 4. Remote Controller (1EA) 5.
SVR-1630 Executive Summary 3. Description of the Front/Rear View SVR-1630 Front View (1) Power Switch (2) HDD Removable Rack (3) Function Buttons (4) Channel Buttons (5) Status LED (6) Jog Shuttle for Search and Playback (7) Function Switch (8) Play and Search Button...
Page 11
Executive Summary SVR-1630 SVR-1630 Rear View (14) BNC connector for video output (15) BNC connector for video input (16) BNC connector for Monitor A output (17) BNC connector for Monitor A input (18) Ethernet connector (19) GND (20) Input/output terminal for RS232 & RS422/485...
Installation and Connection 4. Basic Connection and Start-up 4.1 Overall Layout (1) The devices that can be connected to the SVR-1630 are described below. See each relevant section in the installation manual for the contents on the figure. Samsung Techwin...
SVR-1630 4.2 Connecting a Camera (1) Connect a camera to the SVR-1630 using the coaxial cable as shown in the figure below. <Note> 1. The input video type should be either NTSC or PAL. Do not use both types at the same time.
Monitor as shown in the figure below. <Note> 1. The SVR-1630 monitor outputs are divided into A (Normal) and B (Spot). If only one monitor is connected, connect Monitor A. 2. For Monitor Output A, the same video output is transferred to two BNC connectors and an S-VHS connector.
Installation and Connection SVR-1630 4.4 Connecting Audio (1) Connect an audio signal to the SVR-1630 using the RCA cable as shown in the figure below. Samsung Techwin 2004. 07. 2001 (v 1.0)
<Note> 1. Connect the power cable, press the power switch, and the device starts booting. 2.Press and release the power switch while SVR-1630 is ON, the following windows are displayed according to the system setting after 4 seconds. When there is Admin password in “System Setup”...
5.1 Menu Configuration Press the [MENU] button on the keypad on the front panel, and the system changes to the SVR-1630 Setup mode. The OSD Menu is displayed as shown in the figure below. The Jog/Shuttle on the menu is controlled as described in the figure below.
SVR-1630 Installation and Connection (1) Main Menu : The selected tab is shown in blue and the related sub-menus will be shown below the tab. ◀/▶ ] arrow buttons. To move to the relevant sub- To move to the previous/next Main Menu Tab, use the [ menu, press the [ENTER] or [▼] buttons.
Installation and Connection SVR-1630 6. Remote Controller Setup and Basic Control 6.1 Setting ID of SVR-1630 SVR-1630s with one remote controller, multiple DVRs can be set by one remote When controlling several controller. Set the remote controller ID as described below.
ID button of the remote controller. When the DVR ID matches the remote controller ID, the LED on the front of the SVR-1630 lights up and a buzzer sounds for two seconds. <Note> Up to 16 Remote Controller IDs are supported, which consist of two digits from 1 to 4.
Page 21
Installation and Connection SVR-1630 3. Replace the battery cover. Samsung Techwin 2004. 07. 2001 (v 1.0)
SVR-1630 Installation and Connection 8. SVR-1630 Basic Setting 8.1 Viewing Images After initial start-up, images are displayed in a split screen corresponding to the number of channels connected to the monitor. <Note> If the user password is set, a prompt for entering the password will appear. The keypad on the front panel won’t work.
Installation and Connection SVR-1630 8.2 Setting Date and Time (1) Press the [MENU] button, and select the “Quick Setup” tab on the OSD Menu. [▼] button and press [ENTER]. (2) Select “Date/Time” using the [ENTER] or 8.2.1 Time Zone [◀/▶] or [▲/▼] arrow buttons and press the [ENTER] button.
SVR-1630 Installation and Connection 8.2.4 Time Format ◀/▶ ] or [▲/▼] buttons and press [ENTER]. (1) Select “Time Format” using the [ 메모 [E1]: 추가 (2) Two Time Formats are available; ‘MM/DD/YYYY’ ,‘YYYY/MM/DD’ ‘DD/MM/YYYY’. Select a value using the [▲/▼] buttons, and press the [ESC] button when finished. (Default value is ‘MM/DD/YYYY’.) 8.2.5 Date Mode...
Installation and Connection SVR-1630 (1) Press the [MENU] button, and select “Quick Setup.” (2) Move to a sub-menu by pressing [ENTER] or the [▼] button. (3) Select “Recording” using the [▲/▼] buttons and press the [ENTER] button. 8.3.1 Configuration Status Displays the recording configuration status.
SVR-1630 Installation and Connection 8.3.3 Record Rate/Quality (1) Select “Recording Speed/Quality” using the [▲/▼] buttons and press the [ENTER] button. ◀/▶ ] buttons. Press the [ESC] button when finished. (2) Select a value using the [ <Note> Record Rate/Quality means Low : Rate=1fps and Quality=Q5 Std.
Installation and Connection SVR-1630 9. Using Input/Output Terminals <Note> Wiring Terminating Wires The wires for the TERMINAL BLOCK are terminated as described below. When solid and stranded wires are used, be careful because the thickness of usable wires varies. Stranded Wire: Strip the outer covering to the defined length (8~10mm) and solder it.
SVR-1630 Installation and Connection 9.1 Connecting and Configuring the Sensor 9.1.1 Specification The sensor input of the SVR-1630 has the specifications and normal operating conditions as described below. No. of Input Circuits 16 Photocoupler Inputs Input Type N.C, N.O supported...
1. Sensor setting is for deciding whether to use sensors, and the sensor type. Storing according to sensor inputs and relay should be set separately. 2. See “Event Rec.” of the “SVR-1630 User Manual” for storing and “Event Act” for relay output. Samsung Techwin...
SVR-1630 Installation and Connection 9.2 Connecting and Setting Relay Output 9.2.1 Specification The alarm output of the SVR-1630 has the specifications and normal operating conditions as described below. No. of Output Circuits Automatic output of 4 Relays Spec. Output Method...
Relays can also be controlled locally by pressing the [RELAY] button followed by the relay number. Relays can also be controlled remotely through the “SVR Manager software.” <Note> See the “SVR-1630 User Manual” for setting details. Samsung Techwin 2004. 07. 2001 (v 1.0)
9.3.1 Connecting Serial Communication Ports for Pan/Tilt/Zoom PTZ devices can only be connected and controlled provided that the SVR-1630 supports a through COM port. Check the models available in the SVR-1630OSD Menu. The figure below is an example for connecting an RS485 (COM2) communication terminal to a PTZ camera.
9.3.4 Configuring a Serial Port SVR-1630 “System / Serial Setup” . Configure the COM port for PTZ and available models in the After completing the serial setup, configure the base address or port for each channel under the “Camera” menu tab.
9.4 Connecting an External Device to a Serial Port 9.4.1 Connecting Text Input Devices (ATM / POS / Access Control) In addition to images, the SVR-1630 can record text data received from a POS/ATM through the RS232 serial port (COM1).
Installation and Connection SVR-1630 9.4.2 Configuring Serial Setup (COM1) (1) Select “System” from the OSD Menu and go to the Sub-menu. (2) Select COM1 RS232 in “Serial Setup” and set the Device to “Text”. (3) Set the Baud Rate/Parity/Stop bit/Data bits to the same values as the input device.
SVR-1630 Installation and Connection 9.4.3 Configuring Text (1) Select “Event Source” from the OSD Menu and go to the sub-menu. (2) Select “Text” and set the text related data. <Note> Some external devices may not be recognized, depending on their characteristics. Before installing any external device, consult your local vendor.
Installation and Connection SVR-1630 9.5 Connecting a USB Device A USB port generally uses a USB memtory for a simple video copy. For connecting a USB device, its rated values shall not exceed the specification defined below. USB Spec. Ver 1.1 (Max 12M bps)
2. See the “SVR-1630 User’s Manual” for details about Copy functions. 9.6 Connecting Video In/Out For the SVR-1630, the loop through Video In and Out automatically detects the connection status and sets the terminal resistance. For example, if only Video In is connected, the terminal resistance is internally set to 75Ω. If both Video In and Out are connected, the terminal resistance is changed to Hi-z.
10. HDD 10.1 Adding and Replacing HDDs on the HDD Rack 10.1.1 Available HDDs SVR-1630 . If a non-recommended HDD is used, It is recommended to use the following HDD models with the Samsung Techwin’s warranty will not cover any failures.
Page 44
(3) Unlock the rack by turning the key anti-clockwise. (4) Pull the handle of the HDD RACK to completely remove the rack from the SVR-1630 main unit. (5) Remove the cover by pulling the hook on the cover as shown in the figure below.
Page 45
(Fix the HDD with care, avoiding giving it any knocks.) (7) Drop the handle and push the rack until it reaches the back of the SVR-1630’s main unit. (8) Lock the rack using a key.
10.2 Adding and Replacing External Storage Device 10.2.1 IEEE1394 Port The SVR-1630 used IEEE1394 for the external storage device interface. It has two IEEE1394 ports, one SVR-1630 can expand storage capacity up to 4TB. each on the front and rear panel. With them the <Note>...
Installation and Connection SVR-1630 10.3 Registering and Formatting an HDD The “Disk Manager” will automatically run on start-up after installing a HDD. If the “Disk Manager” doesn’t run automatically on start-up, make sure the HDD is properly installed. (1) Press the [ENTER] button at “Select Disk”.
Installation and Connection 11. Remote Monitoring and Control The SVR-1630 can be accessed using a remote PC via the Internet/Intranet. As with the local site, the SVR- 1630 can be controlled and monitored from remote sites via the Internet/Intranet. 11.1 Connecting via Ethernet (1) Turn off the SVR-1630’s power switch.
Installation and Connection SVR-1630 11.2 Configuring an SVR-1630 Network The following description is on based on Ethernet connection. For more detailed information on the Network SVR-1630 User Manual” Settings Page and when xDSL is used, please refer to the “...
SVR-1630 Installation and Connection 12. Using the SVR Manager 12.1 PC System Requirements for running the SVR Manager Minimum Requirements Recommended Requirements P-Ⅲ 600MHz or above P-Ⅲ 1GHz or above 128 MB or above 256 MB or above 16 MB or above...
Page 51
Installation and Connection SVR-1630 (1) Press the “Next” button. (2) Browse and choose a directory if the default directory is not preferred. Click the “Install” button, after selecting a directory to install into. (3) Click the “Close” button after the SVR Manager program is installed successfully.
SVR-1630 Installation and Connection 12.3 Uninstalling the SVR Manager (1) Click the Windows “Start” Button. (2) Select and Click the ‘Uninstall’ icon to run the Uninstall Shield. (3) Uninstall the program according to the instructions in the window. 12.4 Configstation Click the icon on the desktop to run the “SVR Manager Configstation”...
Installation and Connection SVR-1630 12.5 Monitor Click the related icon and run the “SVR Manager Monitor” program. Samsung Techwin 2004. 07. 2001 (v 1.0)
SVR-1630 Installation and Connection 12.6 Playback Click the related icon and run the “SVR Manager Playback” program. Samsung Techwin 2004. 07. 2004 (v 1.0)
24. (2) All of the connected HDDs are recognized as one virtual disk, and the SVR-1630 supports up to 4TB. (3) The HDD that is firstly connected becomes the primary disk and other HDDs are classified to auxiliary disks.
Appendix SVR-1630 1.1.3 Disk Manager (1) When an HDD is added or deleted physically, the Disk Manager runs automatically after rebooting. If it “Menu Disk Disk Manager” from the console. doesn’t, you can run (2) HDD Type depending on successful formatting of the HDD Available for recording Connected and formatted as a DVR file system.
SVR-1630 Appendix (3) HDD Managing Command Adds an HDD for recording. The HDD added is automatically formatted. Add Used Adds an HDD that has been used and formatted. There is no need to reformat. Only possible when the HDD is added as a Primary Disk.
Appendix SVR-1630 1.3 Keeping Data To keep stored data for certain periods or semi-permanently, you should separate and keep HDDs with data on them. 1.3.1 Backup (1) Connect a backup HDD to an IEEE1394 port. (2) Go to playback mode by pressing the [Playback] button.
SVR-1630 Appendix 1.3.2 Separating and Preserving HDDs HDDs with data on them can be kept separately only when the HDD is installed and used in the DVR (including the primary disk and RAID). It is recommended to use an external HDD rather than an internal HDD. In other words only connect one external HDD, and then keep it when it is full of data.
Appendix SVR-1630 2. Changing Video Type The SVR-1630 changes video type by automatically detecting the video signals. If there are no video signals, the SVR-1630 refers to the internal jumper status and indicates the type. Jumper Setting Video Type NTSC Video PAL Video <Note>...
SVR-1630 Appendix Using CD-Rom 3.1 CD- ROM DISC Components Installation Guide : SVR-1630 Installation Guide User Guide : SVR-1630 User Guide : SVR Manager User Guide SVR Manager (SVR Remote Management Program) Acrobat Reader : Version 5.1 3.2 Preparation To read the User Manual in the CD-ROM Disc, Adobe Acrobat 5.0 should be installed in the client PC.