Introduction Thank you for purchasing a Samsung SVR series digital video recorder. This manual is for SVR-3200, SVR-1680, SVR-1660, SVR-1645, SVR-960, SVR-945. Before product installation and operation, please become thoroughly familiar with this user manual and other manuals referenced by this manual.
Page 3
Install Manual This product is not for exclusive use of crime prevention but for assistance in cases as fire or theft. We take no responsibility for damage from any incident. Experience and technical skills are needed for the installation of this product as an improper installation may cause fire, electric shocks, or defects.
Install Manual Chapter 1. Safety Precautions 1.1 Symbols Displayed for Each Item Warning Refers to information users need to know in order to prevent serious injury or death. Before installation Verify the supplied voltage (AC 100V ~ AC 240V) before connecting the power supply.
Page 6
This product is a supplementary rather than primary means for preventing fire or theft. We are not responsible for incidents or damage that may occur. Samsung Techwin cares for the environment at all product manufacturing stages, and is taking a number of steps to provide customers with more environmentally friendly products.
Page 7
Install Manual FCC Compliance Statement NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
32/16/9 channels to its built-in hard disk. The buttons on the front of the unit as well as the mouse and GUI allow easy setup and operation. The Samsung SVR series of digital video recorders (DVRs) provide additional safety and security to banks, apartment buildings and complexes, government offices as well as other public, private and commercial facilities.
SVR series DVRs provide real time audio recording. Simultaneous recording of 16/9 channels of audio in real time SVR-3200/1680/1600/1645 : Input - 16 channels (4 RCA in rear, 12 D-SUB) Output - 1 in rear SVR-960/945 : 9 channels (4 RCA in rear, 5 D-SUB), Output - 1 in rear...
Playback by event log entry (sensor, video loss, motion detection and text) Remote controller and Jog/Shuttle further improve searching (The SVR-960/945 models do not support Jog/Shuttle.) Full-frame playback (Available in SVR-3200/1680/1660 only) Data Storage The hard disk included with the product is for data storage. If desired, recorded data can be backed up or stored to DVD-R, CD-R or a USB storage device.
Page 11
Install Manual Networking The product supports LAN, xDSL and other networking capabilities. Combined with the PC interface client, the core features of the device can be easily remotely controlled. E-mails can be sent via TCP/IP or DHCP upon an event trigger Remote live visual feed (single or 4 section split-screen) PC playback, storage, search and DVR control functions via Network Viewer Remote recording, search and playback scheduling...
Install Manual 2.2 Components Please check the included accessories as follows. For the SVR-945, a switched-mode power supply (SMPS) power cord is included, while a stand is included instead of the standard rack mount.
Install Manual Description of product 2.3.1 Front view Classification Function For copying recorded video and images to DVD/CD DVD-Multi for copying optical media. (Exception: The SVR-945 uses an external copy device.) Channel LED Shows the input and event action status. Jog can adjust setting values, control the STEP function, navigate through the menu, and adjust the JOG/SHUTTLE...
Page 14
Changes split-screen sections for live video feeds or playback. AUTO Starts or stops user defined sequences. Starts or stops PTZ. MONITOR SVR-3200/1680: Cycles through from monitor 1 to 4. SVR-1600/1645/960/945: Switches between the main and sub monitor. MENU Navigates into the Menu. SEARCH Starts Search mode.
POWER IN Socket for AC 100V ~ AC 240V power cord. CH1 ~ 32 (16/9) Connection terminal for camera BNC input. SVR-3200: 32 ea., SVR-960/945: 9 ea. LOOP OUT Connection terminal for camera BNC output (loop). MONITOR 1 ~ 4 Connection terminal for monitor BNC output.
Page 16
Install Manual Input/Output terminal Function name Serial Port (Terminal Block) RS-232C D-SUB connector. RELAY OUT Connection terminal for relay output. SENSOR IN Connection terminal for sensor input. AUDIO IN(D-SUB) Connection terminal for audio output D-SUB. D-I/O Connection terminal for DIGITAL IN/OUT. Please refer to the detailed description for installation &...
Install Manual 2.3.3 Remote control All DVR unit features can be controlled with the remote controller; multiple units can be controlled with a single remote controller. Unit IDs should be set in the Remote ID screen. Press the ID button on the remote controller to set unit IDs. Classification Function Selects ID.
Page 18
Install Manual Classification Function (◀) Moves cursor left in setup menu. (▶) Moves cursor right in setup menu. (▲) Moves cursor up in setup menu. (▼) Moves cursor down in setup menu. ENTER Saves settings and execute. Cancels settings or navigates up in menu.
Install Manual Chapter 3. Installation 3.1 Installation & Connection 3.1.1 Basic connection and operation 3.1.1.1 Camera connection Connect the DVR and CCTV cameras using coaxial cable as in the following figure. - The cameras’ video input type must be one and only of NTSC or PAL. Both types should not be used together.
Install Manual 3.1.1.3 Audio connection Audio equipment connects to the DVR unit using RCA audio cables or D-SUB as shown in the following figure. Refer to the following figure when connecting D-SUB. The audio inputs are pin numbers 5 ~ 16. 3.1.1.4 Power connection &...
Install Manual OSD Menu structure & Operation 3.2.1 Menu structure Press the [MENU] button on the front panel to change to setup mode and display the following dialog. (1) Main menu: The currently selected tab is highlighted in blue with submenus and options displayed below.
Install Manual 3.2.1.1 Character input dialog box The characters input dialog lets you input text. Character input Use the cursor [▲/▼] and [◀/▶] keys to choose characters then press [Enter] to input it. Use [ ] to backspace, and [ ] to insert a space. When finished, press [Enter] to exit the character input dialog with the newly inputted value.
Page 23
Install Manual Remote Control ID supports a maximum of 16 IDs. For unused remote controllers, set Remote Control ID to Off. 3.2.2.2 Selecting IDs A single remote controller can be used for several DVR units that each have unique IDs. To select a specific DVR, press the ID button on the remote controller repeatedly (maximum of 16 times) until a beep sounds for 2 seconds.
Connect the cameras, monitors and audio. 3.2.3.2 Extended connection diagram Connect the cameras, monitors, audio, sensors, relays and other peripherals. 3.2.3.3 External storage and backup connection diagram Connect a USB memory device or a “Samsung SVS-5E external HDD (eSATA)” unit.
Install Manual 3.2.3.4 Internet/Intranet connection diagram 3.2.4 Basic setup 3.2.4.1 Video check The product automatically powers on when the power cord is plugged in. Once it finishes booting up, the default 16 channel split-screen is displayed. If a password for the unit has been set, the password input dialog is displayed. Only the numeric buttons work here and all others are temporarily disabled until the correct password is entered.
Page 26
Install Manual Time Zone (1) Press [◀/▶] or [▲/▼] to select “Time Zone”, and then press [Enter]. (2) Press [◀/▶] to set the correct Time Zone, and then press [ESC]. Daylight Saving (1) The daylight saving time option is available for time zones where it is used. (2) Press [◀/▶] or [▲/▼] to select “Daylight Saving”, and then press [Enter].
Install Manual (1) Press [◀/▶] or [▲/▼] to select “Apply Date / Time” and then press [Enter]. A confirmation dialog is displayed as shown below. (2) Press [◀/▶] or [▲/▼] to select “YES” and then press [Enter]. Press [ESC] to cancel the new date/time and return to the original value from before.
Page 28
Install Manual Quality As with the recording speed option, the recording quality option is only available when a user defined “Schedule” is set. (1) Press [▲/▼] to select “Quality”, and then press [Enter]. (2) Press [◀/▶] to set a value, and then press [ESC] key. Resolution (1) There are 3 predefined values available: CIF, HALF (2CIF), and D1 (4CIF).
Install Manual Using input/output terminals 3.3.1 Handling cable ends The following details how to handle cables for the terminal block. Please note that different gauges of wire are needed for stranded wire and solid wire. - Stranded wire: Strip 8 ~ 10㎜ of insulation off the end of the wire and solder it together. Use AWG 22 ~ 26 wire.
Page 30
Install Manual Connection method Insert stripped wire end into terminal block Pulse width of usable Minimum 500ms Electric input capacity Output power Typical DC 12mA Sensor input terminal connection Connect sensors to S1 ~ S16 as illustrated in the figure below. Please note that the figure shows connecting sensors with dry contacts.
Page 31
Install Manual This allows setting all 16 sensors simultaneously to off or Normal Open (N.O.) / Normal Close (N.C.). (1) Set the input type after setting "All". Individual sensor This option allows setting each of the 16 sensor input types individually. (1) Select a sensor then press [Enter].
Page 32
Relay Out Settings Relays can be operated with sensor or motion detection and even operate independently in schedules. Relays can also be controlled remotely over the network with the Samsung Network Manager software. For more information, refer to the user manual.
Page 33
Install Manual as Relay out, the Output can be operated with digital I/O. Also, if Input is operated, the emergency recording is started. Then the emergency recording starts to record with the Event Record value. Specification The D-I/O specifications are as follows. No.
Page 34
The following figures illustrate how to connect PTZ cameras through the RS-422/485 port (COM2/COM4) and how to connect other devices through the serial port connection terminals. Refer to the section on handling wiring for more information about connecting or disconnecting wires. [SVR-3200, 1680, 1660] [SVR-1645, 960, 945]...
Page 36
Install Manual COM3 connection diagram (RS-232) PTZ, Keyboard Compatible List 모델명 제조사 SDZ160/330, Samsung SPD SAMSUNG TECHWIN Keyboard SCC3000, Samsung SRX-100B BOSCH BOSCH AutoDome, TC8560X-4 PELCO PELCO(P), PELCO(D) HONEYWELL Honeywell 755/655, HRX-2000, ScanDome2 SONY Sony EVI-D3x VT VPT-4x AD SpeedDome SUNGJIN SungJin SJ372R1’...
Page 37
Install Manual TOKINA Tokina KODICOM Kodicom KRE NUVICO Nuvico Serial Settings PTZ and other serial devices can be configured through Communication > Serial. After Serial setup is completed, configure PTZ address or ports for each channel in the "Camera Display" menu. If a PTZ device is connected to multiple cameras, make sure that PTZ addresses are configured correctly.
Page 38
Install Manual As shown in the above figure, COM1/RS-232 (9-pin D-SUB) are used to receive text data that is configured under the OSD Communication > Event menu. Serial Settings (COM1) (1) In the OSD menu, navigate to Communication > Serial. (2) Set the “Serial Number”...
Page 39
The storage device should be formatted with the FAT32 file system. Supported storage devices are automatically recognized when copying. To copy video, set copying options in the Copy dialog, select the storage device, then copy the data. [SVR-960/945] [SVR-1680/1660/1645] [SVR-3200] [RE4 Copy]...
Page 40
Install Manual [AVI Copy] Some USB storage devices may require additional software and drivers. Care should be taken in these cases as the DVR may not recognize some USB products like this. If copied files do not playback on another computer, double check that proper playback software and codecs are installed.
One eSATA external storage device can be connected through the eSATA port in the back of the DVR unit for a maximum of 8TB of storage space. The eSATA port only supports the “SVS-5E” eSATA external HDD from Samsung Techwin.
Install Manual 3.3.4.2 eSATA device connection Use the eSATA port in the back of the DVR unit to connect your SVS-5E external HDD. External storage requires its own power source as the DVR unit does not supply power to it. Since some external devices may not be recognized if connected with the DVR unit on, the following procedure should be followed.
Install Manual (3) If prompted to format the disk, select “YES”. (4) Close “Disk Manager” by pressing [ESC]. 3.3.5 Remote monitoring & control Connections can be made through Internet/Intranet by using the remote computer. This connection can be used to control DVRs and monitor areas same as local spot. 3.3.5.1 Ethernet connection (1) Shut the DVR power off.
Page 44
Install Manual When using Ethernet Set the type to Ethernet and fill in the IP address, Netmask, Gateway, and DNS information provided by your network administrator. Use Up/Down direction keys or the mouse wheel to select the items, and then setup with the appropriate values. When using PPPoE Change the network configuration type to xDSL then navigate to the xDSL menu.
Install Manual Trouble Shooting 1. DVR does not boot Check power Check power cord 2. Monitor does not display camera video Check monitor power Check cable between the monitor and DVR Check monitor cable port Check that DVR power is on 3.
Page 46
Install Manual 8. Front buttons do not work Check DVR power Check screen lock status 9. Cannot connect to network Check that network cable is properly connected Check DVR IP address Check PC IP address Run a ping test 10. When to contact your reseller If any of the following happen, immediately turn of the DVR and contact the reseller that you purchased it from.
Imation (16X) Sony (16X) Sony (16X) Specification Item Description Display SVR-3200: 32 composite video 0.5–2 Vpp, 75 ohm automatic termination SVR-1680/1660/1645: 16 composite video 0.5–2 Inputs Video Vpp, 75 ohm automatic termination SVR-960/945: 9 composite video 0.5–2 Vpp, 75 ohm automatic termination...
Page 48
Protocol support and NTP Monitoring CMS Software (SNM-128S/P), Built-in web server SVR-3200/1680/1660: 16 TB Maximum capacity Storage SVR-1645/960/945: 8 TB SVR-3200/1680/1660: 4 HDD Internal HDD SVR-1645/960/945: 2 HDD SVR-3200/1680/1660: External eSATA 2 port External HDD SVR-1645/960/945: External eSATA 1 port...
Page 49
PTZ Keyboard RS-485, max. signal voltage ±12 V 2 USB 2.0 ports SVR-3200/1680/1660: External eSATA 2 port eSATA SVR-1645/960/945: External eSATA 1 port Application support ATM/POS, Mouse, Remote Controller Supported PTZ cameras Samsung Techwin, Pelco D, Pelco P, Panasonic, Dome...
Page 50
Install Manual Bosch, SEC Protocols General Input voltage 100 to 240 VAC ±10%; 50/60 Hz, Auto-ranging Electrical Power consumption Max. 65 W (with 1x HDD) Max. 90 W (with 4x HDD) Environmental Operating temperature +5°C to +40°C (+32°F to +104°F) Operating humidity 0% RH to 60% RH 445 x 88 x 388 ㎜...