Electrical Component Summary - Ricoh D014 Service Manual

OVERALL MACHINE INFORMATION

4.4 ELECTRICAL COMPONENT SUMMARY

Motors
No. Name
M01 Shift Tray Exit Motor
M02 Shift Tray Lift Motor
M03 Exit Guide Motor
M04 Stapler Exit Motor
M05 Upper Tray Exit Motor
M06 Shift Motor
M07 Upper Tray Junction Gate
Motor
M08 Stapler Junction Gate Motor
M09 Pre-Stack Junction Gate
Motor
M10 Pre-Stack Transport Motor
M11 Pre-Stack Stopper Motor
M12 Positioning Roller Motor
M13 Positioning Roller Drive
Motor
M14 Drag Drive Motor
M15 Drag Roller Motor
M16 Jogger Motor
M17 Stack Feed-Out Belt Motor
M18 Stack Plate Motor (Center)
M19 Stack Plate Motor (Front)
M20 Stack Plate Motor (Rear)
M21 Stapler Movement Motor
M22 Stapler Rotation Motor
M23 Staple Hammer Motor
M24
Top Fence Motor
M25
Bottom Fence Motor
M27 Upper Transport Motor
B830
CÓPIA NÃO CONTROLADA
Drives the exit roller for the shift tray.
Moves the shift tray up or down.
Opens and closes the upper exit guide. When stapling starts, the
exit guide motor opens the upper exit guide, which includes the
upper shift tray exit roller, in order to feed out the leading edge of
the copy set smoothly. The exit guide motor turns on again a
certain time after stapling is complete, and the upper exit guide
plate is lowered. Then the shift tray exit roller takes over the stack
feed-out. The on-off timing of the exit guide motor is detected by
the exit guide HP sensor.
Drives the rollers that feed stapled stacks out of the stapling unit.
Drives the rollers that output paper to the proof tray (top tray).
Moves the shift tray from side to side.
Operates the upper tray junction gate.
Operates the staple junction gate that directs paper into the
stapling path.
Operates the pre-stack junction gates that direct paper into path 1,
2, or 3 of the pre-stack unit.
Drives the rollers that feed paper into the pre-stack paper paths.
Controls the stopper that stops the sheets in the pre-stack unit and
then releases them to the staple tray.
Moves the positioning roller into contact with the paper.
Rotates the positioning roller.
Extends the sponge roller that drags the stapled stack on the shift
tray toward the finisher so that the edge of the stack is aligned
against the back of the shift tray.
Rotates the drag roller counter-clockwise to pull the ejected paper
toward the machine so that the edge of the stack on the shift tray
is aligned against the back of the shift tray.
Moves the jogger fences of the stapling tray.
Drives the stack feed-out belt which lifts the stapled stack and
feeds it out of the finisher. The stack-feed-out motor turns off when
the pawl actuates the stack feed-out belt home position sensor.
Presses down the center of the edge for stapling.
Presses down the front corner of the edge for stapling.
Presses down the rear corner of the edge for stapling.
Moves the staple unit side-to-side.
Rotates the stapler 45 degrees for oblique stapling.
Drives the staple hammer.
After the specified number of sheets has been fed, this motor
lowers the top fence against the leading edges of the sheets to
align them for stapling and then raises the top fence to its home
position after stapling.
Operates the top fence that jogs pre-stacked paper vertically (in
the direction of paper feed).
After the specified number of sheets has been fed, this motor
lowers the bottom fence to position the stack for stapling and then
raises the bottom fence to its home position after stapling.
Feeds paper in the upper transport area. Drives the rollers that
transport paper toward the proof tray (top tray).
70
CÓPIA NÃO CONTROLADA
Description
SM