Table of Contents
Advertisement
7.7 CLEANING THE ENAMELLED METAL PARTS
When cleaning the enamelled metal parts of the product use a soft cloth moistened with water.
Never clean metal parts using alcohol, solvents, petroleum-based products, acetones or other degreasing or abrasive substances.
In the event of such substances being used the manufacturer cannot be held responsible for any damage caused. Discolouration of metal parts may be
the result of misuse.
7.8 CLEANING THE GLASS (DAILY)
The glass should be cleaned when cold using ammonia-based degreasing agents and not corrosive substances such as solvents.
If the appliance is very slow to heat up in the ignition phase, this is likely to cause a build-up of tar on the glass. This will eventually burn off when the
appliance is operating at full capacity. If the tar is left to build up over a long period it will require more effort to remove. We therefore recommend
that the glass be cleaned daily before lighting the stove.
Do not use any material that could scratch or spoil the glass, as scratches may develop into cracks or breaks.
7.9 REPLACING THE GLASS
The door of the stove is equipped with a ceramic glass window 4 mm thick, resistant to temperatures up to 750°C; the glass can only be broken by a
strong blow or improper use. Do not slam the door or hit the glass. Should the glass break, only replace it with a spare part from the Superior factory.
Proceed as follows to replace the glass:
- Equip yourself with an appropriate pair of protective gloves.
- Remove the door and lay it on a fl at surface.
- Unfasten the screws which can be seen on the inner side of the door.
- Carefully remove the glass clips and the glass.
- If the fi bre glass washer and sealing strip are worn, replace them.
- Replace the glass and relocate the clips, refasten the screws taking care not to overtighten them.
- Re-hang the door.
If other problems arise it is recommended that you speak to the local supplier.
7.10 REPLACING THE REMOTE CONTROL BATTERY
The remote control is optional.
To change the battery proceed as follows: using a small Philips head screwdriver, remove the screw on the back of the handset. Then holding it upside
down remove the back casing. Replace the battery (type A23 12V) being careful not to reverse the polarity (the battery type and polarity are shown on the
back of the handset). Close the handset and dispose of the old battery in the appropriate way.
7.11 CLEANING THE FANS
Any cleaning or maintenance work must be carried out after the CURRENT HAS BEEN SWITCHED OFF.
The stove is fi tted with fans (smoke extractor and heating) positioned at the bottom rear of the stove. Any build-up of dust or ash on the blades can
unbalance them resulting in noise during operation. It is necessary to have the fans cleaned annually. Since such an operation involves dismantling certain
parts of the stove, have the cleaning carried out only by a Superior Service Centre or other qualifi ed persons.
7.12 SHUTTING DOWN
When shutting the stove down for the summer, proceed as follows:
- remove all pellets from the hopper and feeding auger;
- carefully clean the grate, the grate support and the ash drawer;
- using a steel brush, clean the baffl e plate or internal baffl e plates of the fi rebox and coat them using the spray paint, supplied on request, to prevent them
from oxidising and consequently forming rust.
If the cast-iron parts inside the fi rebox are not coated, rust could form. This is a natural process, which does not affect the effi ciency
and quality of the product.
- clean the fl ue thoroughly: contact a professional chimneysweep for this purpose;
- clean by removing all dust, cobwebs, etc. from the area behind the inner lining panels once a year, in particular the fans;
- disconnect the power cable from the power supply;
- remove the batteries from the remote control
7.13 PROGRAMMING MAINTENANCE
The following maintenance should be carried out ONCE A YEAR and is necessary to ensure effi cient and safe stove operation.
• Clean the fi rebox thoroughly.
• Clean and inspect the fl ue.
• Check the condition of seals and gaskets.
• Clean mechanical and moving parts (motors and fans).
• Check electrical and electronic components.
H07023380 / DT2000477-03
DT2010061-03
DT2010062-04
DT2010093-05
DT2010094-00
DT2010095-06
DT2011801-00
DT2010097-03
37
Hide quick links:
Advertisement
Table of Contents
