Table of Contents
Advertisement
3.0 PREPARING FOR INSTALLATION
To prevent accidents or damage to the product we recommend the following:
- unpacking and installation must be carried out by at least two people;
the product must always be moved and handled with suitable equipment in
- full compliance with current safety regulations;
- the packaged product must be kept in the position according to the
directions shown by the diagrams and notices on the pack;
- if ropes, straps or chains are used, ensure that they are able to take the
weight of the pack and that they are in good condition;
- use slow continuous movements when moving the pack to avoid jerking
the ropes, chains, etc.;
- do not tilt the package excessively to avoid toppling;
- never stand in the vicinity of loading/unloading equipment (forklift trucks,
cranes, etc.). Before proceeding with installation, remove the securing
brackets (A) having removed the relative fastening screws. (Fig. 26)
Unpack the product being careful not to damage or scratch it, take
the accessories kit and any pieces of polystyrene or cardboard
used to wedge moveable parts etc. out of the stove.
Keep packaging (plastic bags, polystyrene, etc.) out of reach
of children, since it could be a potential source of danger, and
dispose of according to local regulations.
4.0 INSTALLATION
Pursuant to current regulations on the safety of electrical equipment, you
must contact a Superior After-Sales Service Centre or a qualifi ed electrician
for all and any work connected with installation, maintenance or servicing
that involves access to electrical parts.
Cladding
Having completed assembly of the stove and installed any external room
thermostat, check that the humidifi er (optional) is properly inserted into its
seat (see the paragraph "HUMIDIFIER") and fi nally fi t the ceramic panel into
the top. (Fig. 27)
4.1 ELECTRICAL CONNECTION AND CONTROLS
Power cable (7).
• The stove/fi replace comes with a power cable which must be connected
to a 230V/50Hz mains socket. Connection to the rear of the stove/fi replace
is shown in fi g. 28.
• The power rating is indicated in the paragraph "TECHNICAL DATA".
The appliance must be connected to an efficient earthing/
grounding system.
Ensure that in its normal position the power cable does not
come into contact with any heated parts.
Ensure that the electrical plug is accessible also after
installation of the stove.
Room sensor connection (5).
• When installing the stove/fi replace, it is necessary to connect the room
sensor (provided) to the correct jack (fi g. 28). The sensor can be positioned
as shown in fi g. 29, otherwise remove the band, uncoil the lead and then
place the sensor in a spot where a more accurate room temperature reading
can be obtained.
Pipe tap (3).
• The appliance has an external socket for measuring the pressure (vacuum)
of the fl ue gas outlet pipe. This control and verifi cation should be carried out
by authorised personnel at the time of installation or during maintenance.
To make moving and handling of the stove easier for installation
purposes, it is advisable to remove the cladding in accordance
with the procedure described in the paragraph "REMOVING THE
CLADDING" and then refi t it upon completion of installation.
If you decide to install the stove without removing the cladding, take
great care not to buckle, scratch or in any way damage the bottom
of the side panels and the lower front panel.
Fig. 26
A
Fig. 27
DT2011593-01
Connection to the DB9 serial socket (7)
• The appliance has a DB9 serial socket, which is used to check appliance
operation. Controls should be carried out by authorised personnel at the
time of installation or during maintenance.
• The optional GPRS kit, if ordered, may be connected to the DB9 serial
socket.
Fig. 28
3
1
2
7
4
1 External socket for connection of room
sensor.
2 Socket for power lead.
3 External pressure pipe tap.
H07023380 / DT2000477-03
Fig. 29
6
DT2032281-00
DT20322
4 Knockout for inserting cable gland PG7
for connection of external thermostat.
5 Room sensor connection.
6 Power cable connection.
7 DB9 serial socket
DT2011688-00
A
DT2032443-00
DT2011597-00
DT2032296-00
DT2011601-01
5
DT2032282-0
DT2032282-00
15
Hide quick links:
Advertisement
Table of Contents
