Panasonic FP0 Series Specifications page 18

FP0 Series
Specification tables
Interfaces
Item
Programming TOOL-Port
Communication COM-Port
Input specifications
Item
Insulation method
Rated input voltage
Operating voltage range
Rated input current
Input points per common
ON voltage/ON current
OFF voltage/OFF current
Input impedance
Response time
Operating indicator
Note: (*): Since the response time of X0 to X5 is very fast (for high-speed counter input), the FP0 happens to catch chattering noise as an input signal.
To prevent this, it is recommended that timer instruction should be included in the program.
Output specifications
1) Relay output type
Item
Output type
Rated control capacity
OFF ON
Response time
ON OFF
Mechanical
Life
Electrical
Surge absorber
Operation indicator
The FP0 series conforms to the following standards under the EMC Directive
and the Low Voltage Directive.
EMC Directive (89/336/EEC)
EN 50081-2: 1993
EN 50082-2: 1995
CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
RS232, mini DIN socket (5 pin), 9600 or 19200 BAUD, (8 data bits, odd parity, 1 stop bit), Computer link for
programming and communication with MEWTOCOL.COM, user configurable modem connection
RS232 (SD, RD, GND) 3 way screw terminal, 300 to 19200 BAUD, (7 or 8 data bits, none/even/odd parity,
1 or 2 stop bits, start code: none/STX, end code: CR/CR+LF/ETX/none, CCU mode for programming and
communication with MEWTOCOL.COM, user configurable modem connection, GENERAL PURPOSE MODE
controlled by program for general purpose RS232 communication.
Optical coupler
24VDC
21.6 to 26.4VDC
4.3mA or less (at 24VDC)
6 points/common (C10RS) 8 points/common (C14RS,C16T/C16P,E16T/E16P) 16 points/common (C32T/C32P,E32T/E32P)
19.2V or less/ 3mA or less
2.4V or more/ 1mA or more
Approx. 5.6k
50µs or less (at X0,X1)(*)
OFF ON
100µs or less (at X2 to X5)
2ms or less (at X6 to XF)
ON OFF
same as above
LED display
Description
Normally open(1 Form A)
2A 250VAC, 2A 30VDC(4.5A/common)
10ms or less
8ms or less
20million operations or more
100k operations or more
None
LED display
Low Voltage Directive (73/23/EEC)
VDE 0160: 1988 (EN 50178: 1995)
(Overvoltage Category II,
non-mains-circuit, pollution degree 2)
EN 61131-2: 1995
Description
Description
2) Transistor output type
Item
Insulation method
Output type
Rated load voltage
Load voltage allowable range
Max. load current
Max. inrush current
Leakage current at OFF time
Max. voltage down at ON time
External power
supply
(For internal circuit)
OFF
Response time
ON
Surge absorber
Operating indicator
Notes:
(*1): 8points/common(C16T/C16P,E16T/E16P), 16points/common(C32T/C32P,
T32CP, E32T/E32P)
(*2): 50µs or less at Y0, Y1 only
10/2004
Description
Optical coupler
Open collector
24VDC 5 to 24VDC
4.75 to 26.4VDC
0.1A/points(at DC26.4V) (1A/common)(*1)
0.3A
100µA or less
1.5V or less
Voltage 21.6 to 26.4VDC
Current 240mA or less
ON
1ms or less
OFF
1ms or less(*2)
Zener diode
LED display