Panasonic WJ-NT104 Operating Instructions Manual page 60

q CAMERA SELECT (Left window panel)
To select a camera (camera 1 to 16) connected to the
WJ-FS616 Video Multiplexer. The image of the select-
ed camera is displayed in spot mode.
w PRESET SELECT (Left window panel)
To move the combination camera (option) connected to
the WJ-FS616 to any of 8 preset positions.
e ALARM LIST
Any image before or after alarm input can be temporar-
ily stored in the internal memory of the WJ-NT104. For
alarm display see ALARM LIST on page 37.
r CAMERA SELECT (Bottom window panel)
To select a camera (camera 1 to 16) connected to the
WJ-FS616. Select a camera number, and then click
[SET] to apply it. The image of the selected camera is
displayed in spot mode.
t MULTISCREEN SELECT
Clicking this button repeatedly will switch the screen as
follows:
4 7 9
y PRESET SELECT (Bottom window panel)
To move the combination camera (option) connected to
the WJ-FS616 to any of 64 preset positions. Select a
preset position number, and then click the [SET] button
to move the camera to the position.
u ALARM ALL RESET
To reset all alarms activated in the Video Multiplexer,
and return it to normal condition.
i PAN/TILT
Clicking anywhere on the live image moves the con-
nected combination camera (option) up and down, or
to the right and left.
decreases as the point clicked moves closer to the
image center. Clicking the image center will not move
the camera. Zooming does not change the camera
pan/tilt angle. Click the image repeatedly to move the
camera to the desired position. You cannot pan or tilt
the camera continuously by dragging on the live
image.
o ZOOM
The connected combination camera (option) can be
zoomed by clicking the [TELE] or [WIDE] button under
ZOOM.
Clicking the [TELE] or [WIDE] button will operate the
camera in telescopic or wide-angle mode for a speci-
fied time, after which the mode is released automatical-
ly. These modes cannot be retained by keeping the
[TELE] or [WIDE] button depressed. You need to click
the [TELE] or [WIDE] button again.
60
10 13 16 4 screen segments
The camera pan/tilt angle
!0 FOCUS
The connected combination camera (option) can be
focused by clicking the [FAR], [NEAR] or [AUTO] but-
ton under FOCUS.
Clicking the [FAR] or [NEAR] button will operate the
camera in focusing mode for a specified time, after
which the mode is released automatically. Clicking the
[AUTO] button will automatically focus the image on
the screen. Focus control cannot be retained by keep-
ing the [FAR] or [NEAR] button depressed. You need
to click the [FAR] or [NEAR] button again.
!1 IRIS
The connected combination camera (option) can be
controlled to close or open the iris by clicking the
[CLOSE] or [OPEN] button under IRIS.
Clicking the [OPEN] or [CLOSE] button will open or
close the camera iris for a specified time, after which
the operation is released automatically.
Clicking the [RESET] button on the screen will reset
the iris of the displayed camera to the factory default
setting. Iris control cannot be retained by keeping the
[OPEN] or [CLOSE] button depressed. You need to
click the [OPEN] or [CLOSE] button again.
!2 AUTO PAN
The auto pan status of the connected combination
camera (option) can be changed by clicking the [ON]
or [OFF] button under AUTOPAN.
Note: Note: When LOCAL is selected in the camera
setup menu, auto pan is released automatically
after 1 minute. When REMOTE is selected, auto
pan will not be released automatically.
!3 Image Display
The image output from the MULTISCREEN OUT con-
nector of the video multiplexer connected to the WJ-
NT104 is displayed.