Table of Contents
Advertisement
> Before Start
> Part Names
Surround
Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 "Full Band" can be selected only when "Front" is set to "Full
Band".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
LPF of LFE
Set the low-pass filter for LFE (low-frequency effect) signals in
order to pass lower frequency signals than the set value and
thus cancel unwanted noises. The low-pass filter will be effective
only on sources with LFE channel.
The value from "80Hz" to "120Hz (Default Value)" can be set.
"Off": Do not use this function
Double Bass
This can be selected only when "Configuration" - "Subwoofer" is
set to "Yes" and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and
right, and center speakers to the subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
0 The setting will not automatically be configured even if you
performed AccuEQ Room Calibration.
■ 3. Distance
Set the distance from each speaker to the listening position.
Front Left
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Center
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Front Right
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
Surround Right
Specify the distance between each speaker and the listening
position. (Default Value is "7.0ft/2.10m")
52
> Install
> Initial Setup
> Playback
Surround Left
Specify the distance between each speaker and the listening
position. (Default Value is "7.0ft/2.10m")
Subwoofer
Specify the distance between each speaker and the listening
position. (Default Value is "12.0ft/3.60m")
0 Default values vary depending on the regions.
0 Distance units can be switched by pressing Mode on the remote controller. When the unit
is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1 ft. When the unit
is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
■ 4. Level Calibration
Front Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Center
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Front Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Surround Right
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Surround Left
Select a value between "j12 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Subwoofer
Select a value between "j15 dB" and "i12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Advanced Setup
| Firmware Update | Others
Hide quick links:
Advertisement
Table of Contents
