SA-HT740GCP CONTENTS Page Page 1 Safety Precautions 9.1. Service Mode Summary Table 1.1. GENERAL GUIDELINES 9.2. Service Mode Table 1.2. Before Repair and Adjustment 9.3. DVD Self Diagnostic Function-Error Code 1.3. Protection Circuitry 9.4. Sales Demonstration Lock Function 2 Prevention of Electro Static Discharge (ESD) to 9.5.
Page 4
SA-HT740GCP 10.15. Disassembly of Switch Regulator IC (IC5701) 20.2. (B) Main Circuit 10.16. Disassembly of the Tray Base Guide (L) and Tray Base 20.3. (C) Power, AC-inlet, Sub power & Voltage Selector Circuit Guide (R) 10.17. Disassembly of the Rotary Tray 20.4.
SA-HT740GCP 1 Safety Precautions 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
SA-HT740GCP 1.2.1. Caution for fuse replacement 1.3. Protection Circuitry The protection circuitry may have operated if either of the following conditions are noticed: · No sound is heard when the power is turned on. · Sound stops during a performance.
SA-HT740GCP 3 Precaution of Laser Diode CAUTION: This unit utilizes a class 1 laser. Invisible laser radiation is emitted from the optical pickup lens. Wavelength: 662nm(DVD)/785nm(CD). Maximum output radiation power from pickup: 100µW/VDE When the unit is turned on: 1. Do not look directly into the pick up lens.
SA-HT740GCP 4 About Lead Free Solder (PbF) 4.1. Service caution based on legal restrictions 4.1.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
SA-HT740GCP 5 Handling Precautions for Traverse Unit The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid caution to electrostatic breakdown when servicing and handling the laser diode.
SA-HT740GCP 6 Accessories AC cord Remote control AM loop antenna Speaker cable FM indoor antenna Speaker label Video Cable Power plug adaptor Screws...
SA-HT740GCP 7 Operation Procedures 7.1. Remote Control Key Buttons Operations Television operations Change the television's video input mode VIDEO Turn the unit on/off Adjust the television volume VOLUME Select the source MUSIC DVD/CD, FM/AM, AUX/FRONT MUSIC P./REAR MUSIC P. Select television channels Select disc's title numbers etc./Enter...
SA-HT740GCP 7.2. Main Unit Key Buttons Operations (SA-HT740) Standby/on switch [POWER Press to switch the unit from on to standby mode OPEN/CLOSE or vice versa. In standby mode, the unit is still Open/Close the disc drawer consuming a small amount of power.
Recorded with devices using Version 1.1 of the Video Recording Format (a unified video recording DVD-VR standard), such as DVD video recorders, DVD video cameras, personal computers, etc. JPEG Recorded with Panasonic SD multi cameras or DVD video recorders using the DCF (Design rule for Camera File System) Standard Version 1.0. DVD-R (DVD-Video)
Page 16
SA-HT740GCP 7.3.2. File Extension Type Support (WMA/MP3/JPEG) Tips for making data discs When there are more than 8 groups, the eighth group onwards will be displayed on one vertical line in the menu screen. There may be differences in the display order on the menu screen and computer screen.
SA-HT740GCP 9 Self-Diagnosis and special mode setting 9.1. Service Mode Summary Table The service modes can be activated by pressing various button combination on the player and remote control unit. Below is the summary of major checking: Player buttons Remote control unit buttons...
SA-HT740GCP 9.2.1. Service Mode Table 1 Item Key Operation FL Display Mode Name Description Front Key Jitter check Jitter check In STOP (no disc) mode, Jitter rate is measured and displayed. press STOP button on the Measurement is repeatedly done in player, and "5"...
Page 21
SA-HT740GCP 9.2.2. Service Mode Table 2 Item Key Operation FL Display Mode Name Description Front Key Micro-processor firmware version Micro-processor In STOP (no disc) firmware version display & EEPROM checksum display. mode, press STOP button display & on the player, and "7"...
Page 22
SA-HT740GCP 9.2.3. Service Mode Table 3 Item Key Operation FL Display Mode Name Description Front Key In STOP (no disc) Timer 1 check Timer 1 check mode, press STOP button Laser operation timer is measured on the player, and "...
Page 23
SA-HT740GCP Note: Press " FL DISPLAY " button on remote control Note: Press " FL DISPLAY " button on remote control unit for next page display unit for next page display...
SA-HT740GCP 9.3. DVD Self Diagnostic Function-Error Code Error Diagnosis Contents Description of error Automatic FL Display Remarks Code Focus servo error Focus coil NG (OPU unit abnormal) Press [ n STOP] on main unit for next error. Tray loading error /...
Page 25
SA-HT740GCP Error Diagnosis Contents Description of error Automatic FL Display Remarks Code F602 Access failure to LEAD-IN LEAD IN data unreadable Press [ n STOP] on main caused by demodulation unit for next error error F603 Access failure to KEYDET...
SA-HT740GCP Error Diagnosis Contents Description of error Automatic FL Display Remarks Code F895 Language area Firm version agreement check for factory Press [ n STOP] on main abnormality preset setting failure prevention unit for next error F896 No existence model...
Page 27
SA-HT740GCP · Recovery disc (Product number: RFKZD03R005) [SPG] · Performing recovery process 1. Load the recovery disc on to the player and run it. 2. Recovery is performed automatically. When it is finished, a message appears on the screen. 3. Remove the recovery disc.
SA-HT740GCP 10 Assembling and Disassembling “ATTENTION SERVICER” Be careful when disassembling and servicing. Some chassis components may have sharp edges. Special Note: 1. This section describes the disassembly procedures for all the major printed circuit boards and main components. 2. Before the disassembly process was carried out, do take special note that all safety precautions are to be carried out.
SA-HT740GCP 10.3. Disassembling the Top Cabinet Step 1 Remove 7 screws. Step 2 Remove the top cabinet in the direction of arrow. 10.4. Disassembling the Front Panel Assembly Step 5 Detach the FFC cables from connectors (CN5705, CN5707 & CN2013).
SA-HT740GCP Step 4 Remove the FL & Head phone P.C.B. 10.11. Disassembling the Main P.C.B. 10.9. Disassembling the HDMI · Follow (Step 1) to (Step 4) of Item 10.6. Module P.C.B. · Follow (Step 1) to (Step 4) of Item 10.7.
SA-HT740GCP Selector P.C.B. Note: Refer to the diagrams of Power P.C.B. (Section 20.3) for location of the parts. 10.15. Disassembly of Switch Caution: Remember to use tie wraps to tie the black/red wires to the side of bottom chassis after repair or Regulator IC (IC5701) troubleshooting.
SA-HT740GCP 10.16. Disassembly of the Tray Base 10.17. Disassembly of the Rotary Guide (L) and Tray Base Guide Tray · Follow (Step 1) to (Step 3) of Item 10.5. · Follow (Step 1) to (Step 3) of Item 10.5. Step 1 Remove the 2 screws.
SA-HT740GCP 10.18. Disassembly of the Traverse 10.17.2. Disassembly of the Close Lock Gear Unit · Follow (Step 1) to (Step 3) of Item 10.5. · Follow the Item 10.7. Step 1 Remove 1 screw. Step 1 Rotate cam gear anti-clockwise. (Align at position (A) as marking on gear with arrow) Step 2 Flip the base mecha unit in vertical position.
SA-HT740GCP Step 2 Remove Drive Gear (A) and Drive Gear (B). Step 3 Release the 2 claws in the direction of arrow (1), and then push the pulley pin in the direction of arrow (2). 10.18.2. Disassembly of the Loading Motor P.C.B.
SA-HT740GCP Step 2 Remove 1 screw and support piece. 10.19. Assembly of Tray Assembly Step 1 Rotate cam gear anti-clockwise. Align at position (C) as marking on gear with arrow. 10.18.6. Disassembly of the Slide Plate (L) & (R) and Change Lever Step 1 Press the claw and push the Slide Plate (L) up.
Page 39
SA-HT740GCP Step 3 Push tray assembly to the direction of arrow shown.
SA-HT740GCP 11 Service Fixture and Tools Prepare service tools before proccess service position. Service Tools Loading Motor P.C.B. - Main REEX0633 (11 pin) P.C.B. Sensor P.C.B. - Power P.C.B. REEX0465 (11 pin) 12 Service Positions 12.1. Checking & Repair Main P.C.B., Power P.C.B., HDMI...
SA-HT740GCP 13 Measurements and Adjustments 13.1. Service Tools and Equipment Application Name Number Tilt adjustment DVD test disc DVDT-S20 [SPG] TORX screw driver (T6) Available on sales route. (T6) or RFKZ0185 [SPG] Others Grease RFKXPG641 [SPG] Confirmation CD test disc...
SA-HT740GCP 15 Voltage and Waveform Chart 15.1. HDMI Module P.C.B. IC3701 Re f No. MODE CD P LAY IC3701 Re f No. MODE CD P LAY Re f No. IC3701 MODE CD P LAY IC3701 Re f No. MODE CD P LAY IC3701 Re f No.
Page 46
SA-HT740GCP IC8051 Re f No. MODE CD P LAY IC8051 Re f No. MODE CD P LAY IC8051 Re f No. MODE CD P LAY Re f No. IC8111 MODE CD P LAY IC8151 Re f No. MODE CD P LAY IC8251 Re f No.
SA-HT740GCP 15.2. Main P.C.B. IC2001 Re f No. MODE CD P LAY S TANDBY IC2001 Re f No. MODE CD P LAY S TANDBY IC2001 Re f No. MODE CD P LAY S TANDBY IC2001 Re f No. MODE CD P LAY...
SA-HT740GCP 15.3. Power P.C.B. IC5001 Re f No. MODE CD P LAY 11.8 11.9 S TANDBY 11.8 11.9 Re f No. IC5001 MODE CD P LAY 12.0 56.5 56.5 -3.1 S TANDBY 12.0 56.5 56.5 -3.1 Re f No. IC5001...
SA-HT740GCP 15.5. Loading Motor P.C.B., Tray Motor P.C.B., Sensor P.C.B., Regulator P.C.B. Loading Motor P.C.B. Q9001 Re f No. MODE CD P LAY S TANDBY Tray Motor P.C.B. Q9101 Q9102 Re f No. MODE CD P LAY S TANDBY -0.2 Sensor P.C.B.
S-VIDEO OUT (SOLDER SIDE) 11 10 CN2001 CN2002 HDMI MODULE P.C.B. Loading (SIDE:A) Motor CN2013 FC9101 SENSOR TO TUNER PACK UNIT P.C.B. (SOLDER SIDE) CN9102 FP8251 FP8531 TO WIRELESS P3901 TO SPINDLE MOTOR ASS'Y TO OPTICAL SA-HT740GCP WIRING CONNECTION PICKUP...
Page 56
( Not Supplied) IC3931 BUFFER EXDT0 C0JBAA000344 AND GATE TXRST DATA HOTPLG OP CPU CMD DVD CMD EXDT15 IC8695 AND GATE C0JBAA000346 DVD STAT OP CPU STAT IC8691 AND GATE C0JBAA000346 DVD CLK OP CPU CLK AMUTE SA-HT740GCP BLOCK DIAGRAM...
Page 57
SHIFT REGISTER LATCH POWER ON RESET DVD CLK DVD CK DVD CMD DVD CMD DVD STAT DVD STA ST/DO IC2001 ST / DO TU SDA MN101C49GHF1 TU SD SYSTEM CONTROL POWER FM DET SUPPLY TU SCL (FM:ON) (FM) SA-HT740GCP BLOCK DIAGRAM...
SA-HT740GCP 19 Schematic Diagram Notes Put a conductive mat on the work table. Do not touch the legs of IC or LSI with the fingers directly. · This schematic diagram may be modified at any time with the development of new technology.
Page 85
SA-HT740GCP 22 Basic Troubleshooting Guide 22.1. Basic Troubleshooting Guide for Traverse Unit (HDMI Module P.C.B) Problems Checking Points Checking components 1) Distorted picture or abnormal a) Check SDRAM address, data bus, CLK and IC8051 sound is heard during initialisation other control signals waveform...
Page 86
SA-HT740GCP 22.2. Basic Troubleshooting Guide for HDMI AV output Problems Checking Points Checking components 1) TV does not have display. Set 1) Check setting of the set in Setup Menu whether FL display shows U702 / U703. HDMI video output is turned ON.
SA-HT740GCP 23.2. HT740 Block (Analog Signal : DVD 5.1ch Play Back Mode)
Page 90
SA-HT740GCP 23.3. HT740 Block (Analog Signal : 2ch Analog Input Mode)
Page 91
SA-HT740GCP 23.4. HT740 Power Supply Block...
Page 92
SA-HT740GCP 23.5. HT740 Power Block (SMPS)
Page 93
SA-HT740GCP 24 Terminal Function of ICs 24.1. IC2001 (MN101C49GHF1): Terminal Function Name Micro-processor IC MUTE_HP Headphone mute MP_SEL Select front MPort or rear MPort Terminal Function (SELECT Name AVSS Power supply for A_D converter SUB_ Subwoofer frequency Limiter LIMITER KEY1...
Page 94
SA-HT740GCP 25 Exploded Views 25.1. Cabinet Parts Location...
Page 98
SA-HT740GCP 26 Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety purpose. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufacture’s specified parts shown in the parts list.
Page 99
SA-HT740GCP 26.1. Component Parts List Ref. Part No. Part Name & Description Remarks RGQ0446-K TRAY BASE Ref. Part No. Part Name & Description Remarks RGQ0359-K1 ROTARY TRAY RMM0254-2 SLIDE PLATE R CABINET AND CHASSIS RMB0842 TRAY SPRING RME0384 CLOSE LOCK GEAR SPRING...
Page 100
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks IC2102 C1BB00001098 IC ASP Q5014 B1ABCF000011 TRANSISTOR IC2103 C0AABB000125 IC HEADPHONES AMP Q5015 B1ADBL000010 TRANSISTOR IC2105 C0ABCB000088 IC MUSIC PORT AMP Q5022 B1ABCF000011...
Page 101
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks D5012 B0ACCE000003 DIODE LB8305 J0JBC0000042 CHIP BEAD D5013 B0ACCE000003 DIODE LB8401 J0JBC0000042 CHIP BEAD D5031 B0BC3R400001 DIODE LB8421 ERJ2GE0R00X CHIP JUMPER D5041 B0ACCK000005...
Page 102
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks CN6902 K1MN19AA0004 19P CONNECTOR L6903 J0JBC0000041 CHIP INDUCTOR CN9102 K1MY11BA0021 11P CONNECTOR L6904 J0JBC0000019 CHIP INDUCTOR CN9003 K1MY11BA0021 11P CONNECTOR L6905 J0JBC0000019 CHIP INDUCTOR...
Page 103
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2045 ERJ3GEYJ221V 220 1/16W P3901 K1FY119H0001 CONNECTOR R2048 ERJ3GEY0R00V 0 1/16W P5701 K2AA2B000015 JK AC INLET R2049 ERJ3GEY0R00V 0 1/16W R2051 ERJ3GEYJ103V 10K 1/16W...
Page 104
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2214 ERJ3GEYJ153V 15K 1/16W R2621 ERJ3GEYJ393V 39K 1/16W R2215 ERJ3GEYJ272V 2.7K 1/16W R2622 ERJ3GEY0R00V 0 1/16W R2218 ERJ3GEY0R00V 0 1/16W R2623 ERJ3GEYJ563V 56K 1/16W...
Page 105
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2976 ERJ3GEYJ103V 10K 1/16W R5183 ERJ1TYJ220U 22 1W R2977 ERJ3GEYJ103V 10K 1/16W R5189 ERJ3GEYJ823V 82K 1/16W R2979 ERJ3GEYJ103V 10K 1/16W R5197 ERJ3GEYJ103V 10K 1/16W...
Page 106
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R5744 ERJ3GEYJ153V 15K 1/16W R6803 ERJ3GEYJ122V 1.2K 1/16W R5745 ERJ3GEYJ103V 10K 1/16W R6804 ERJ3GEYJ102V 1K 1/16W R5746 ERJ3GEYJ473V 47K 1/16W R6805 ERJ3GEYJ102V 1K 1/16W...
Page 107
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R8555 ERJ2GEJ2R2X 2.2 2W W2030 ERJ6GEY0R00V CHIP RESISTOR R8556 ERJ3GEYJ560V 56 1/16W W2031 ERJ6GEY0R00V CHIP RESISTOR R8557 ERJ3GEYJ510V 51 1/16W W2037 ERX2SJ1R5E RESISTOR...
Page 108
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks W4005 ERJ3GEY0R00V CHIP JUMPER C2002 ECJ1VB1C104K 0.1 16V W4006 ERJ6GEY0R00V CHIP RESISTOR C2003 ECEA1EKS220B 22 25V W4007 ERJ3GEY0R00V CHIP JUMPER C2004 ECJ1VB1H103K 0.01 50V...
Page 109
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C2279 ECJ1VC1H470J 47P 50V C2810 ECJ1VB1H103K 0.01 50V C2280 ECJ1VB1C104K 0.1 16V C2811 ECJ1VB1C104K 0.1 16V C2281 ECJ1VB1H102K 1000P 50V C2812 ECJ1VB1C104K 0.1 16V...
Page 110
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C2966 ECJ1VB1H103K 0.01 50V C5035 ECJ1VB1H104K 0.1 50V C2967 ECJ1VB1H103K 0.01 50V C5036 ECJ1VB1H104K 0.1 50V C2968 ECEA1CKA101B 100 16V C5040 ECJ1VB1H104K 0.1 50V...
Page 111
SA-HT740GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C5722 ECJ1VB1H104K 0.1 50V C8007 ECJ0EF1C104Z 0.1 16V C5723 ECJ1VB1H104K 0.1 50V C8008 ECJ0EF1C104Z 0.1 16V C5725 ECA1HAK2R2XB 2.2 50V C8011 F2G0J101A066 100 6.3V...