Table of Contents
Advertisement
Accessing the settings - adjustment - problem identification
menus
The boiler can be used to manage the heating system in its
entirety.
Navigation within the menus enables the boiler system +
connected peripheral units to be customised, optimising
operation for maximum comfort and maximum saving. It also
provides important information relating to the efficient operation
of the boiler.
The following menus are available:
0 Time-Date-Language
0
0
Set Dispaly Language
0
1
Set Time-Date
0
British Summer Time
1 Set Timer
2 Boiler Parameter
1
Service code (34)
General setting
3
C.H. Parameters - Part 1
4
C.H. Parameters - Part 1
5
Domestic Hot Water (COMBI Only)
9
Menù Reset to factory setting
3 Solar & Storage
3
0
General setting
3
1
Service code (34)
3
Special setting
4 Zone 1 Parameters
4
0
Set-point Zone1
4
1
Service code (34)
4
Zone 1 Setting
4
3
Diagnostics
4
4
Zone device mangement
Zone 2 Parameters
5
5
0
Set-point Zone
5
1
Service code (34)
5
Zone Setting
5
3
Diagnostics
5
4
Zone device mangement
5
5
Multizone
7 Test & Utilities
8 Service Parameter
8
1
Service code (34)
8
Boiler
8
3
Boiler Temperature
8
4
Solar & Storage
8
5
Service
8
6
Statistics
8
7
E@sy - NOT ACTIVE
8
8
Error History
Supplied By www.heating spares.co Tel. 0161 620 6677
settings - adjustment - problem identification menus
The parameters relating to each individual menu are listed in the
following pages.
The various parameters can be accessed and modified using the
M
the menus and of each individual parameter will be shown on the
display.
Encoder
(adjustment
knob)
Enables the
See manual user's
set values to
be increased
or decreased
On the display, the information relating to the menus and to the
See manual user's
individual parameters are indicated by the figures and by the scrolling
text shown in the figure below.
To access the Menus, open the cover and proceed as follows:
1. Press the M
. Turn the encoder to select a menu; the text on the display will
3. Press the M
4. Press the M
5. Turn the encoder in a clockwise direction to select code 234 -
6. Press the M
7. Turn the encoder to select a sub menu; the text on the display
8. Press the M
9. Turn the encoder to select a parameter; the text on the display
10. Press the M
11. Turn the encoder to select the new value, e.g. "75".
1. Press M
To exit, press the e
restored.
For menus which do not require the access code, it is possible to pass
directly from the menu to the sub menu.
/o
button and the encoder (see fig. below). The description of
enu
k
ABCDEFGHIL123456
/o
button; the first figure
enu
k
display.
indicate the title of the pre-selected menu, for example:
Boiler parameters".
/o
button; the first two figures on the display will
enu
k
flash and the access code will flash, e.g.
Caution! The menus reserved for qualified technicians may only
be accessed after setting the access code.
/o
button; 222 will appear on the display unit.
enu
k
Correct code.
/o
button to select the sub menu; the first two
enu
k
figures will flash, e.g. "220".
will indicate the title of the pre-selected sub menu, for example:
"230
- Heating - Part 1".
/o
button to access the sub menu parameters; the
enu
k
three figures will flash, for example: "230".
will indicate the title of the pre-selected parameter, for example:
"231
- Max. Adjustable Heating Power".
/o
button to access the parameter; the display will
enu
k
indicate the value, e.g "70".
Note: The parameter value will be displayed for 0 seconds, then
will begin to flash in alternation with the parameter, e.g.
231.
/o
to save the change or press e
enu
k
saving.
button until the normal display screen is
sc
Menu/Ok-
button
will flash on the
000
"200
-
"210
- Access code".
"70
>
to exit without
sc
37
Hide quick links:
Advertisement
Table of Contents
