Self-Diagnosis Code Table - Sony Handycam DCR-PC115 Service Manual

DCR-PC115/PC115E/PC120BT/PC120E
4.

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0
C 2 1 0
C 2 2 0
C 3 1 1
C 3 1 1
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 3
C 3 1 4
C 3 1 4
C 3 1 1
C 3 1 1
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 3
C 3 2 4
C 3 2 4
E 0
6 1
E 1
6 1
E 6 2 0
E 6 2 0
E 9 1 0
Symptom/State
0 Non-standard battery is used.
0 Condensation.
0 Video head is dirty.
LOAD direction. Loading does not
0
complete within specified time
UNLOAD direction. Loading does not
1
complete within specified time
0 T reel side tape slacking when unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0 FG fault when starting capstan.
0 FG fault when starting drum.
2 FG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0 FG fault when starting capstan.
0 FG fault when starting drum
FG fault during normal drum
2
operations
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
0 (With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
1 (With yaw angular velocity sensor output
stopped.)
Charging the flash does not complete
1
witin the specified time.
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus MR sensor (Pin 8,9 of CN151 of
CD-349 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC201 of VC-270 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin ql,wa of CN151 of
CD-349 board) when zooming is performed when the zoom lens is
operated and the zoom motor drive circuit (IC201 of VC-270 board)
when zooming is not performed.
Inspect pitch angular velocity sensor (SE3450 of VM-027 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE3451 of VM-027 board)
peripheral circuits.
Inspect the flash unit (ST1850 and MC1850).
— 10 —
Correction