Fisher & Paykel CG604DX Installation Instructions Manual
Hide thumbs
Also See for CG604DX:
- User manual (20 pages) ,
- Installation instructions manual (13 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel CG604DX
Summary of Contents for Fisher & Paykel CG604DX
- Page 1 INSTALLATION INSTRUCTIONS Gas Cooktop CG604DX & CG905DX models GB IE IN www.fisherpaykel.com 590877A 06.15...
-
Page 3: Important Safety Instructions
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING! Electrical Shock Hazard Please make this information available Before carrying out any work ● ● to the person installing the appliance on the electrical section of the as it could reduce your installation appliance, it must be disconnected costs. - Page 4 SAFETY AND WARNINGS IMPORTANT! Do not use or store flammable ● ● materials on or near this appliance. Regardless of room size, all rooms Do not spray aerosols in the vicinity of containing the appliance must have ● ● this appliance while it is in operation. direct access to the outside air via an Packing elements (eg plastic bags, openable window or equivalent.
- Page 5 SAFETY AND WARNINGS Before you install the appliance, please the supply connection point (gas shut- ● ● make sure that off valve) is accessible after installation. the local distribution conditions (nature the benchtop is made of a heat resistant ● ●...
-
Page 6: Parts Supplied
SAFETY AND WARNINGS If installed with an approved flexible ● ● hose, the hose should not come in contact with the bottom of the appliance or any sharp edges. Flexible hose assemblies should be BS 699.1 certified. Seal exposed bare edges of the cutout ●... -
Page 7: Gas Rate Summary
All appliances are factory set for either Natural Gas or LPG. Check the ‘Gas type’ sticker on the base of the appliance. SEMI-RAPID SEMI-RAPID SEMI-RAPID SEMI-RAPID RAPID MINI WOK CG604DX CG905DX CG604DX SEMI-RAPID MINI WOK GAS TYPE Jet size Nominal... - Page 8 PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE CG604DX CG905DX PRODUCT AND CABINETRY DIMENSIONS Overall height of product (excluding burners, dials and pan supports) Overall width of product Overall depth of product...
-
Page 9: Clearance Dimensions
CLEARANCE DIMENSIONS FRONT CG604DX CG905DX CLEARANCE DIMENSIONS Minimum clearance from left edge of cutout to nearest combustible surface Minimum clearance from right edge of cutout to nearest combustible surface Minimum clearance from rear edge of cutout to: Nearest combustible surface... - Page 10 DISCARD PACKAGING FIT THE ELBOW AND WASHER Model may vary from illustrations shown Foam Tape Adhesive side Ensure edge of tape lines up with outer edge of cooktop Fibre washer Elbow (1/2” BSP external thread) Floating nut Recycle responsibly APPLY ADHESIVE FOAM TAPE AROUND EDGE LOWER GENTLY INTO THE CUTOUT Floating nut Fibre washer...
-
Page 11: Connect To Gas Supply
FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS lifting o yellow tip Foam Tape good ame Adhesive side view from below PG test point adaptor (if using LPG) 16-20mm 20-30mm 30-40mm 40mm+ Repeat on all the other sides Elbow (½”... -
Page 12: Leak Testing
diameter of 10 mm and comply with relevant AS 5601/NZS 5261 requ The hose must not be kinked, subjected to abrasion or permanently d LEAK TESTING The hose must not be near or in contact with any hot surfaces (e.g. base of metal hotlplate, ue, or chassis of underbench oven etc.) Leak testing of the appliance shall be conducted according to the manufacturer’s instructions. -
Page 13: Installation Instructions
INSTALLATION INSTRUCTIONS AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Note: pan supports may vary Duplicate data label TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. -
Page 14: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clamping brackets? Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation? Have you used the fibre washer supplied? Have you sealed all connections with gas tape? Have you leak-tested all connections? Is the cooktop set to the correct working pressure? - Page 16 www.fisherpaykel.com Copyright © Fisher & Paykel Appliances 2015. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.