SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING! Electrical shock hazard Particular attention shall be given to Disconnect the appliance from ● ● the relevant requirements regarding ventilation. the mains electricity supply Read these instructions carefully before before carrying out any work or ●...
Page 4
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS For rooms with a volume between ● ● 5 m3 and 10m3, permanent ventilation This gas appliance is suitable for through a free area of at least 50 cm2 ● ● connection only to the gas type for will be required, unless the room has which it was set at the factory, as a door which opens directly to the...
Page 5
SAFETY AND WARNINGS Before you install the appliance, please the supply connection point (gas shut- ● ● make sure that off valve) is accessible after installation. the local distribution conditions (nature the benchtop is made of a heat resistant ● ●...
Page 6
SAFETY AND WARNINGS When you install the appliance We do not recommend you flush mount ● ● or seal this appliance into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred by doing...
PARTS SUPPLIED Dual Wok Pan support Pan support Small pan support (1) Wok stand (1) Fibre washer (1) Mini wok Pan (Models with a Dual Wok only) (not supplied with support (1) (some models only) Dual Wok only models) (CG604D only) Elbow 1/2“...
GAS RATE SUMMARY All appliances are factory set for either Natural Gas or LPG and are not convertible. Check the ‘Gas type’ sticker on the base of the appliance. CG301D DUAL WOK GAS TYPE Jet size Nominal Nominal (mm) rating...
Page 10
PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE CG301D CG302D CG451D CG603D CG604D CG752D CG903D CG905D PRODUCT AND CABINETRY DIMENSIONS Overall height of product (excluding burners, dials and pan supports)
CLEARANCE DIMENSIONS FRONT CG301D CG302D CG451D CG603D CG604D CG752D CG903D CG905D CLEARANCE DIMENSIONS Minimum clearance from left edge of cutout to nearest combustible surface Minimum clearance from right edge of cutout to nearest combustible surface Minimum clearance from rear edge of cutout to:...
Page 12
Note: Gas inlet connection is located in the rear right corner. REAR SIDE FRONT CG301D CG302D CG451D CG603D CG604D CG752D CG903D CG905D...
Page 13
FLUSH MOUNTING INSTALLATION (OPTIONAL) 5 mm 5 mm 5 mm ROUTER THE BENCHTOP TO THE SPECIFIED DEPTH FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SILICONED 16 - 50mm 16 - 50mm view from below Choose most appropriate slot for benchtop min.
Page 14
DISCARD PACKAGING REMOVE THE TWO TRANSIT SCREWS Model may vary from illustrations shown fting o yellow tip good ame Foam Adhesive side Recycle responsibly Repeat on the other side FIT THE ELBOW AND WASHER LOWER GENTLY INTO THE CUTOUT Floating nut Fibre washer Elbow (½”...
Page 15
FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS lifting o yellow tip Floating nut Elbow (½” BSP external thread) Fibre washer good ame Foam Tape Adhesive side LPG Models NG Models LPG Models view from below Make sure to t the supplied Make sure to t the supplied Make sure to t the supplied regulator.
INSTALLATION INSTRUCTIONS AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label Model may vary TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. ●...
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clamping brackets? Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation? Have you used the fibre washer supplied? Have you sealed all connections with gas tape? Have you leak-tested all connections? Is the cooktop set to the correct working pressure?