Fisher & Paykel CG604DX Installation Instructions Manual
Gas cooktop
Hide thumbs
Also See for CG604DX:
- User manual (20 pages) ,
- Installation instructions manual (17 pages)
Related Manuals for Fisher & Paykel CG604DX
Summary of Contents for Fisher & Paykel CG604DX
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS Gas cooktop CG604DX & CG905DX models NZ AU 590447B 03.13... -
Page 2: Safety And Warnings
SAFETY AND WARNINGS Do not use or store flammable materials on or near this appliance. WARNING! Do not spray aerosols in the vicinity of this appliance while it is in operation. Electrical shock hazard Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these Before carrying out any work on the electrical section of the appliance, it must may cause serious injuries. -
Page 3: Parts Supplied
All appliances are factory set for Natural gas but are convertible to LPG. See ‘Converting to a different gas type’ SEMI-RAPID SEMI-RAPID SEMI-RAPID SEMI-RAPID MINI WOK RAPID CG905DX CG604DX CG604DX & CG905DX BURNER SEMI-RAPID RAPID MINI WOK Nominal Nominal Nominal Nominal... - Page 4 PRODUCT & CABINETRY DIMENSIONS Note: Gas inlet connection is located in the rear right corner. FRONT REAR SIDE Product and cabinetry dimensions (mm) overall height of product (excluding burners, dials and pan supports) overall width of product overall depth of product height of chassis (below top of bench) width of chassis...
-
Page 5: Clearance Dimensions
CLEARANCE DIMENSIONS FRONT Clearance dimensions (mm) minimum clearance from left edge of cutout to nearest combustible surface minimum clearance from right edge of cutout to nearest combustible surface minimum clearance from rear edge of cutout to: nearest combustible surface nearest non-combustible surface minimum height of non-combustible material when used on adjacent walls minimum clearance from cooktop surface to: rangehood... - Page 6 DISCARD PACKAGING FIT THE ELBOW AND WASHER Model may vary from illustrations shown Fibre washer Recycle responsibly Elbow (1/2” BSP external thread) Floating nut APPLY ADHESIVE FOAM TAPE AROUND EDGE LOWER GENTLY INTO THE CUTOUT Foam Tape Turn the cooktop upside down and place it on a soft surface.
-
Page 7: Connect To Gas Supply
FIT CLAMPING BRACKETS BASED ON THE SECURE TO BENCHTOP BENCHTOP THICKNESS view from below Repeat on all the other sides 16-20mm 20-30mm 30-40mm 40mm+ CONNECT TO GAS SUPPLY CHECK ALL CONNECTIONS FOR GAS LEAKS If converting to LPG, see 16 'Converting to a different gas type' Adjust to obtain a test point Make sure the supply pressure pressure of 1 kPa with all the... -
Page 8: Test Operation
AFFIX DUPLICATE DATA LABEL SOMEWHERE FIT PAN SUPPORTS ACCESSIBLE & PLUG COOKTOP IN Ensure the pan supports are located securely and in the correct orientation (refer to User guide) Duplicate data label TEST OPERATION To check that the ignition system operates correctly, light each burner by itself, then all burners in combination. -
Page 9: Converting To A Different Gas Type
Use a 7 mm box spanner. Mini wok burner (CG604DX only) has 1 injector. Use a 7 mm ring spanner. Wok burner (CG905DX only) has 3 injectors. Use a 7 mm ring spanner on two of them. -
Page 10: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Installer’ s name: Have you installed the clamping brackets? Installer’ s signature: Have you verified that the type of model (factory-set for NG or Installation company: converted to LPG) matches the type of gas at the site of installation? Date of installation: Have you used the fibre washer supplied? Have you leak-tested all connections?