Chapter 5 Operating Basics; Switching Power On/Off; Adjusting Volume; Audio Frequency (Af) Gain - Kenwood TS-2000 Instruction Manual

OPERATING BASICS

SWITCHING POWER ON/OFF

1 Switch the DC power supply ON.
2 Press and hold [ ] (POWER) briefly to switch
the transceiver ON.
• Do not press the switch for more than
approximately 2 seconds; the transceiver will
be switched OFF.
• Upon power up, "HELLO" appears, followed by
the selected frequency and other indicators.
PF
F LOCK A
3 To switch the transceiver OFF, press [
(POWER) again.
4 Switch the DC power supply OFF.
• You may skip step 3. After switching the
transceiver ON, you can switch it OFF or ON
using only the power switch of the DC power
supply. The transceiver stores the information
of the POWER switch position when the DC
power source is switched OFF.

ADJUSTING VOLUME

AUDIO FREQUENCY (AF) GAIN

Turn the MAIN AF control clockwise to increase the
audio level and counterclockwise to decrease the
level.
Note: The position of the MAIN AF control does not affect the
volume of beeps caused by pressing keys nor the CW transmit
sidetone. The audio level for Packet operation is also independent of
the MAIN AF control setting.
18
HF/VHE/UHF ALL MO
PF
F LOCK A
MAIN
AUTO
CAR MEN
LSB
USB
MIC
REV
TX MONI
CW
PWR
FSK
DELAY NAR
M
FM
KEY
AM
CLR
SEL
1MHz
DISP CTRL
]
CW TUNE 9.6k STA CON
HF/VHE/UHF ALL MODE MULTI BANDER TS-2000
RIT
RIT/SUB
ALT
XIT
_ +
CLEAR
P.C.T
SET
SUB
UTO
MENU
SB TF-
SB SET
MAIN SUB
SEL SG.SEL
1MHz SCAN
CTRL

RADIO FREQUENCY (RF) GAIN

Set the MAIN RF control fully clockwise. You may
turn it counterclockwise slightly when you have
trouble hearing the desired signal because of
excessive atmospheric noise or interference from
other stations. First take note of the peak S-meter
reading of the desired signal. Then turn the MAIN RF
control counterclockwise until the S-meter reads the
peak value that you noted. Signals that are weaker
than this level will be attenuated and reception of the
station will become easier.
Depending on the type and gain of your antenna, and
the condition of the band, you may also prefer leaving
the MAIN RF control turned counterclockwise by the
same amount rather than turning it fully clockwise.
When using FM mode, always set the MAIN RF
control fully clockwise.

SELECTING VFO A OR VFO B

2 VFOs are available for controlling the frequency on
the main transceiver. Each VFO, VFO A and VFO B,
works independently so that a different frequency and
mode can be selected. When SPLIT operation is
activated, VFO A is used for reception and VFO B is
used for transmission. The opposite combination is
also possible.
Press [A/B] to toggle between VFO A and VFO B.
• "tA" or "tB" appears to indicate which VFO is
selected.

SELECTING A BAND

Press [+] or [–] to select your desired band.
• Holding down either key changes the bands
continuously.
<PANEL>
SUB
MAIN
9.6k STA CON
CW TUNE
HF/VHE/UHF ALL MODE MULTI BANDER TS-2000
RIT
RIT/SUB
ALT
XIT
_
+
CLEAR
P.C.T
SET
SUB
UTO
MENU
SB TF-
SB
SET
MAIN SUB
SEL SG.SEL
1MHz CTRL SCAN
9.6k STA CON
CW TUNE
HF/VHE/UHF ALL MODE MULTI BANDER TS-2000
RIT
RIT/SUB
ALT
XIT
_ +
CLEAR
P.C.T
SET
SUB
UTO
MENU
SB TF-
SB SET
MAIN SUB
SEL SG.SEL
1MHz CTRL SCAN
9.6k STA CON
CW TUNE
HF/VHE/UHF ALL MODE MULTI BANDER TS-2000
RIT
RIT/SUB
ALT
XIT
_ +
CLEAR
P.C.T
SET
SUB
UTO
MENU
SB TF-
SB SET
MAIN SUB
SEL SG.SEL
1MHz CTRL SCAN