Kenwood TS-2000 Instruction Manual page 18

4 GETTING ACQUAINTED
PF
F LOCK A
!9 LSB/ USB/ AUTO key
Press to select lower sideband (LSB) or upper
sideband (USB) mode for voice or digital operation.
Press [FUNC], [LSB/ USB/ AUTO] to toggle the auto
mode selection {page 73}.
@0 CW/ FSK/ REV key
Press to select CW or FSK (Frequency Shift Keying)
mode {pages 30, 51}. Press [FUNC],
[CW/ FSK/ REV] to reverse the sideband pitch.
@1 FM/ AM/ NAR key
Press to select FM or AM mode. Press [FUNC],
[FM/ AM/ NAR ] to select narrow bandwidth
transmission mode {page 29}.
@2 CLR key
Press to exit from, abort, or reset various functions.
Also used to erase memory channels {page 62} or
locking out memory channels from the scan list {page
62}.
@3 DISP key
Press to toggle the normal operating mode and DSP
filter setting display mode {page 55}. Press and hold
to start the Visual Scan function {page 70}.
@4 1MHz/ SEL key
Press to switch the MHz Up/ Down function ON or
OFF using the MULTI/ CH control. Press [FUNC],
[1MHz/ SEL] to change the increment/ decrement
step value {page 37}. Press and hold to start the
MHz Scan function {page 68}.
@5 Tuning control
Turn to select the desired frequency {page 37}. Use the
convenient finger-tip cavity for continuous tuning.
The lever behind this control adjusts the control torque
level; turn fully clockwise for light torque or fully
counterclockwise for heavy torque.
@6 CTRL key
Press to toggle the operating controls between the
main transceiver and the sub-receiver. The
transmission band is not affected by this key.
10
20
19 25
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
MAIN
AUTO
CAR
LSB
USB
MIC
REV
TX MONI
CW
PWR
FSK
DELAY NAR
KEY FM
AM
CLR
SEL
1MHz
DISP CTRL
21
23 24 26
22
@7 MENU key
Press to select or cancel the Menu mode that is used
for activating and configuring functions {page 21}.
@8 TF-SET key
While operating split-frequency, press to monitor or
change your transmit frequency {page 31}.
@9 +/ – (Up/ Down) keys
Press to step through all the Amateur radio bands
consecutively {page 18}. Also used to make
selections from the Menu {page 21}, and to check the
Start and End frequencies of the Scan function
{page 62}.
#0 MAIN key
Press to transfer the operating controls to the MAIN
transceiver. Also moves the transmission band to the
main transceiver frequency.
#1 SUB key
Press to transfer the operating controls to the sub-
receiver. Also moves the trasmission band to the
sub-receiver frequency.
#2 SCAN/ SG.SEL key
Press to start or stop the Scan function {page 66}.
Press [FUNC], [SCAN/ SG.SEL] to select a scan
group {page XX}.
#3 CALL/ C.IN key
Press to recall a call channel for the selected
operating band (HF/ 50 MHz/ 144 MHz/ 430
(440) MHz/ 1.2 GHz (TS-2000 Optional). Press
[FUNC], [CALL/ C.IN] to write a new Call Channel to
the memory {page 75}.
29
27 28 33
CW TUNE
RIT
ALT
XIT
CLEAR
P.C.T
SET
SUB
MENU
TF-
SET
MAIN SUB
SG.SEL
SCAN M.IN
M VFO
32
30 31
9.6k STA CON
RIT/SUB
_
+