Zero Clearance Fireplace Installation; Firebox Panel Kit (Required Accessory); Log Set Installation - Superior DRI3030TEN Installation And Operation Manual

Zero Clearance Fireplace Installation

This appliance may be installed in a masonry or factory built/zero clear-
ance (ZC) fireplace. When installing in a ZC fireplace, the ZC grate must
be removed and the ZC damper must be removed or secured open. The
ZC doors, screen, refractory or masonry lining, baffles and smoke shelf
may be removed if necessary to install the gas insert. However, do not cut
or alter the fireplace components. The removal of any parts to facilitate
installation must not alter the integrity of the inner or outer shells of the
fireplace cabinet. Any parts removed must be replaceable if the insert is
taken out of the fireplace or the fireplace clearly marked with a paint stick
that "This fireplace has been altered and is no longer safe to operate."
This appliance is designed to fit into a ZC fireplace with a minimum firebox
height of 19-1/2" (495mm).
If the factory-built fireplace has no gas access hole(s) provided, an ac-
cess hole of 1-1/2" (37.5 mm) or less may be drilled through the lower
sides or bottom of the firebox in a proper workmanship like manner. This
access hole must be plugged with a non-combustible insulation after the
gas supply line has been installed.
Si le foyer préfabriqué ne comporte pas d'orifices d'amenée du gaz, un
orifice d'au plus 37,5 mm (1,5 po) peut être pratiqué, selon les règles
de l'art, dans la partie inférieure des parois ou au fond de la chambre de
combustion. Cet orifice doit être obturé au moyen d'isolant incombustible
une fois la conduite de gaz en place.
The installer must mechanically attach the marking supplied with the gas
fireplace insert to the inside of the firebox of the fireplace into which the
gas fireplace insert is installed. See Figure 1 on Page 10.
Conversion from Standard 40,000 BTU Natural Gas To Optional
33,000 BTU Natural Gas Input
To convert input from 40,000 BTU's to 33,000 BTU's. (Assuming the
front door is already removed)
1. Remove the log rack (Use a 5/32" allen wrench) by removing two
screws on the front of the log rack and then pulling the log rack out
the front of the firebox.
2. Remove the burner by sliding the burner to the right off the main
burner orifice and out of the air shutter tube. The burner can now
be pulled out of the firebox and carefully placed aside.
3. Remove the main burner orifice (1/2" wrench) by turning the wrench
counterclockwise to loosen and remove.
4. Install new burner orifice #H5924 by placing the orifice in the bulkhead
and turning clockwise. Using a wrench, tighten the orifice until snug.
(Pipe dope or other approved gas line sealant will need to be applied
to the orifice before it is inserted into the bulkhead)
5. Reinstall burner by completing Step 3 in reverse.
6. Reinstall log rack by completing Step 2 in reverse.
7. The foil sticker supplied, stating DRI3030TEN-33 or DRI2530TEN-33,
will need to be affixed below the model name on the serial number
label (located in the control compartment).
Firebox Panel Kit and Log Set Installation
If logs are not installed according to the log installation instructions,
flame impingement and improper combustion could occur and result in
soot and/or excessive production of carbon monoxide (CO), a colorless,
odorless, toxic gas.
The size and position of the log set is critical to achieve a safe, reliable
and attractive flame pattern. Any attempt to use a different log set in the
fireplace will void the warranty and will result in incomplete combustion,
sooting and poor flame quality.
1. Remove the log rack (2 screws) and install the rear log on the retainer.
See Figures 8 and 9.
2. Place the rear firebox panel on the brackets and reinstall the log rack
with the rear log. IMPORTANT!!! SCREWS PASS THROUGH THE LOG
RACK AND THE BURNER PAN.
3. Install the side firebox panels by sliding them into place. See Figure 10.
Figure 8 - Log Rack Screws
Figure 9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Log Rack
Rear Log
17