Superior DRI3030TENC Installation And Operation Manual

Direct-vent fireplace insert
Hide thumbs Also See for DRI3030TENC:

Advertisement

P/N 900124-01 REV. NC 01/2014
Ce manuel d'installation est disponible
en francais, simplement en faire la de-
mande. Numéro de la pièce 900184-01.
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is
not followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
- Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
- Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INSTALLATEUR: Laissez cette notice avec l'appareil.
CONSOMMATEUR: Conservez cette notice pour consul-
tation ultérieure.
Direct-Vent
Fireplace Insert
Report # 100501897PRT-001
P900124-01
AVERTISSEMENT

INSTALLATION AND OPERATION

MODEL
DRI3030TENC
UNE SURFACE VITRÉE CHAUDE PEUT
CAUSER DES BRÛLURES.
LAISSER REFROIDIR LA SURFACE
VITRÉE AVANT D'Y TOUCHER.
NE PERMETTEZ JAMAIS À UN ENFANT
DE TOUCHER LA SURFACE VITRÉE.
AVERTISSEMENT: Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire
au minimum le risque d'incindie ou d'explosion ou
pour éviter tout dommage matériel, toute blessure
ou la mort.
- Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où vous
trouvez.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du fournis-
seur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par
le fournisseur de gaz.

Advertisement

Table of Contents
loading

Summary of Contents for Superior DRI3030TENC

  • Page 1: Installation And Operation

    INSTALLATION AND OPERATION Direct-Vent Fireplace Insert P/N 900124-01 REV. NC 01/2014 MODEL Ce manuel d’installation est disponible Report # 100501897PRT-001 DRI3030TENC en francais, simplement en faire la de- mande. Numéro de la pièce 900184-01. P900124-01 WARNING AVERTISSEMENT HOT GLASS WILL UNE SURFACE VITRÉE CHAUDE PEUT...
  • Page 2: Table Of Contents

    CONGRATULATIONS! Zero Clearance Fireplace Installation ......13 Glass Door ............ 13-14 When you purchased your new gas fireplace insert, you joined Firebox Panel Kit Installation ........14 the ranks of thousands of individuals whose answer to their home Glass Media Installation ........15 heating needs reflects their concern for aesthetics, efficiency and our environment.
  • Page 3: Safety And Warning Information

    IMPORTANT SAFETY AND WARNING AVERTISSEMENT INFORMATION On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à proximité. WARNING WARNING Young children should be carefully supervised when they are in the same room as the appliance. Tod- Any safety screen or guard removed for servicing dlers, young children and others may be susceptible the appliance must be replaced prior to operating...
  • Page 4  T hese appliances are vented gas appliances. Do not burn wood  F OR YOUR SAFETY do not install or operate this appliance without or other material in these appliances. first reading and understanding this manual. Any installation or operation of the appliance deviating from that which is stated  T his appliance is only for use with the type of gas indicated on in this manual WILL void the warranty and may be hazardous.
  • Page 5: Homeowner - Attaching Safety In Operation Warnings

    ATTACHING SAFETY-IN-OPERATION WARNING LABELS ATTACHING SAFETY IN OPERATION WARNINGS COLOCACIóN DE ADVERTENCIAS DE SEGURIDAD APPOSITION DES MISES EN GARDE RELATIVES EN OPERACIóN à LA SéCURITé D’UTILISATION It is required that the set of safety instruction labels that have been furnished with the appliance be affixed Se requiere que el juego de etiquetas de instrucciones Il est impératif que le jeu d’étiquettes de sécurité...
  • Page 6: Orifice Size/Altitude Adjustment

    IMPORTANT: When installing these appliances into a factory ORIFICE SIZE/ALTITUDE ADJUSTMENT built fireplace or heat-form, the air flow within and around the fireplace shall not be altered by the installation of the insert For altitudes above 2,000 feet (In Canada 4,500 FT/1370 M), the orifice (i.e.
  • Page 7: Codes And Approvals

    CODES AND APPROVALS COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS (Massachusetts Approval #G3-1104-102) Certification These appliances are approved for installation in the US state of Mas- Gas appliances must be tested and certified by a nationally recognized sachusetts if the following additional requirements are met: testing and certification laboratory to ANSI (American National Standard Institute) gas appliance safety standards.
  • Page 8: Pre-Installation

    Platinum Glass Media used to convert from NG to LP or LP to NG. Contact your IHP dealer Goldfinger Glass Media for details. Copper Glass Media RATINGS DRI3030TENC NATURAL GAS LP GAS 32,000/21,000 27,000/21,000 Max/Min Input BTUh 0-2,000 Feet (0-610 M) Manifold Pressure (IN.
  • Page 9: Insert And Fireplace Dimensions

    31-1/4" 31-1/8 (794mm) O.D. = 2-15/16" (75mm) 15-7/8" 15-7/8 13-3/8" (403mm) 13-3/8 (340mm) Top View 15-7/8" 15-7/8 (403mm) 19-3/8" 19-3/8 (492mm) Right Side View Front View Left Side View Figure 2 - Insert Dimensions Minimum Fireplace Opening 31-1/2" (800mm) Front Opening Width 19-1/2”...
  • Page 10: Clearances To Combustibles

    Minimum Clearances to Combustibles 3"/76mm 3"/76mm Minimum clearances include any projections such as shelves, window DRI3030TENC sills, mantels, spacers/standoffs or surfaces to combustible construction 3"/76mm etc. above the appliance. Paint or lacquer used to finish the mantel Facing and Mantel 1-1/2”...
  • Page 11: Fan Control Module Switch

    FAN CONTROL MODULE SWITCH INSTALLATION Before installation, verify the power switch on the Fan Control Module is Venting Installation in the ON position (as shown in Figure 6). Your IHP appliance must be vented to the outside in accordance with the current edition of the National Fuel Gas Code ANSI-Z223.1 (In Canada, the current CAN/CGA B149.1 installation code).
  • Page 12: Vertical Venting

    Vertical Venting The existing fireplace chimneys The vent pipes must be connected to the proper collars on the unit and may take various contours the exhaust vent pipe must be connected to the termination cap or the which the flexible liners will unit will not operate.
  • Page 13: Zero Clearance Fireplace Installation

    Zero Clearance Fireplace Installation AVERTISSEMENT This appliance may be installed in a masonry or factory built/zero clear- Ne pas utiliser l'appareil si le panneau frontal en ance (ZC) fireplace. When installing in a ZC fireplace, the ZC grate must be removed and the ZC damper must be removed or secured open. The verre n'est pas en place, est craqué...
  • Page 14: Firebox Panel Kit Installation

    Firebox Panel Kit Installation Instructions: 1. Remove the glass door following the instructions provided in this manual. 2. Remove the two brackets from the firebox using a 5/32" allen wrench (see Figure 11). Retain the screws for step 4, and discard the brackets as they will not be needed.
  • Page 15: Glass Media Installation

    Glass Media Installation Surround Installation The fireplace insert surround panels are made of heavy gage steel for Glass Media Kits (one required) durability and, if desired, for the ease of making an inside fit in the fire- place. See Packaging List for available sizes. Cat.
  • Page 16: Gas Line Installation

    Gas Line Installation Fuel Inlet Pressure Manifold Pressure Type Desired Minimum Maximum On Hi On Lo After leveling, position the insert in the fireplace - holding it about six Fire Fire inches out from its final location. Natural 7" WC 5"...
  • Page 17: Air Shutter Adjustment

    Air Shutter Adjustment Battery Backup - Battery Installation This appliance has an air shutter adjustment lever located behind the This appliance is equipped with a battery backup system. It requires four lower door of the inserts face, directly above the gas valve (see Figures (4) "AA"...
  • Page 18: Operation

    OPERATION WARNING • Improper installation, adjustment, alteration, Pre-Lighting Checklist service or maintenance can cause injury or property damage. For assistance or additional Be sure to check these items before the initial lighting of the insert: information, consult a qualified installer, service agency or your gas supplier.
  • Page 19: Operation

    OPERATION Receiver Remote Control System REMOTE OFF The Remote and Receiver allows you to command the functions of your appliance from the comfort of your chair and is configured to control the On/Off primary burner operation, its flame levels (through six levels) and provides On/Off and Smart thermostatic control of the appliance.
  • Page 20 OPERATION Child Safety Lock-Out Transmission Low Battery Alarm Temperature Indicator Display Thermostat With the system in the “OFF” position, press the Thermostat Key and Room Temperature Off/On/Smart the Mode Key at the same time (see Figure 22). Look at the LCD screen SMART on the Remote to verify that a C or F is visible to the right of the Room Temperature display (see Figure 23).
  • Page 21: Flame Color And Behavior

    OPERATION Burner Flame Appearance Blower Speed Control Soot above Soot at No Soot at Flame Tip Flame Tip Flame Tip This appliance is equipped with a hot air circulating blower. The speed of the blower is controlled by the Remote. The blower speed can be Dark Orange Semi-Transparent Flame...
  • Page 22: Wiring Diagrams

    POWER 120 V AC ROOM AIR BLOWER ADAPTOR BOX FAN CONTROL MODULE 14 - RED 4 - PUR 3 - GRAY BURNER PILOT CONTROL NOTE: SWITCH CONDITIONS BOARD GIVEN AT ROOM TEMPERATURE N/C = NORMALLY CLOSED N/O = NORMALLY OPEN = FEMALE DISCONNECT 4-GRN = MALE DISCONNECT...
  • Page 23: Maintenance And Servicing

    o Check that the area around the insert is kept clear and is free of MAINTENANCE AND SERVICING combustible materials, gasoline and other flammable vapors and liquids. WARNING 2. The viewing glass should be cleaned periodically (see Glass Main- tenance). Turn off gas and electrical power to the fireplace and allow it to cool before cleaning or servicing the appliance.
  • Page 24: Glass Maintenance

    Blower Removal Glass Door Cleaning and Maintenance Unplug the power supply cord from the electrical outlet prior to removing Cleaning: Do not remove or clean the glass door when hot. When cool, the blower. The blower can be accessed through the back wall of the firebox. the glass may be cleaned with a clean, soft cloth and a household glass cleaner.
  • Page 25: Troubleshooting

    TROUBLESHOOTING NOTE: When troubleshooting the gas control system, be sure the external gas shut off valve, located at the gas supply inlet is in the “ON” position. IMPORTANT: Call your gas supplier or plumber for additional help with any gas control problem. Valve system troubleshooting should only be accomplished by a qualified service technician.
  • Page 26 REPLACEMENT PARTS - DRI3030TENC H8859 Cassette Assembly NG 32,000 BTU (if LP, also requires H8858 Conversion Kit) H8490 3/8" NPT Pipe Nipple, 8" H5924 Orifice, Main Burner #36 NG 32,000 BTU Item # Cat. # Description H5964 Orifice, Main Burner #53 LP 27,000 BTU...
  • Page 27 REPLACEMENT PARTS - DRI3030TENC NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
  • Page 28: Accessories

    ACCESSORIES - DRI3030TENC Gas Conversion Product Reference Information Kits Cat. No. Description Ship. Ship. DRI3030TENC-33 Weight Volume F1789 DRI3030TENC 144 lb. 16.9 cu. ft. Cat. No. Model Description H8458 RDV-CK-TCC-LP to NG LP to NG Conversion Kit Porcelain Panel Kit...
  • Page 29 Surround Trim Kits H5143 GFT2941-B Trim/Black 29" x 41" H5145 GFT2948-B Trim/Black 29" x 48" Barrier Screen Kit H5144 GFT3341-B Trim/Black 33" x 41" H5146 GFT3348-B Trim/Black 33" x 48" 75036 GFT2941-G Trim/Gold 29" x 41" 75038 GFT2948-G Trim/Gold 29" x 48" 75040 GFT3341-G Trim/Gold 33"...
  • Page 30: Insert Labels

    SAFETY / LISTING LABEL - DRI3030TENC SERIAL SERIAL Le numéro de série est indiqué dans la MODÈLE MODEL Ravenna™ CD Ravenna™ CD RDV CD DRI3030TENC DRI3030TENC section anglophone de cette étiquette FABRIQUÉ PAR: MANUFACTURED BY: LENNOX HEARTH PRODUCTS Innovative Hearth Products LLC...
  • Page 31 LIGHTING LABEL - DRI3030TENC POUR PLUS DE SÉCURITÉ LIRE AVANT DE METTRE EN MARCHE FOR YOUR SAFETY READ BEFORE OPERATING AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la WARNING: If you do not follow these instructions exactly, a fire or explosion may présente notice risque de déclencher un incendie ou une explosion entraînant des...
  • Page 32 NOTES...
  • Page 33: Warranty

    THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior™ Brand gas fireplace, Stove or Insert ("Product") to be free from defects in materials and workmanship at the time of manufacture. The Product body and firebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only.
  • Page 34: Replacement Parts

    WARRANTY Normally, all parts should be ordered through your IHP distributor or dealer. Parts will be shipped at prevailing prices at time of order. Your gas appliance is covered by a limited warranty (provided with When ordering repair parts, always give the following information: appliance).

Table of Contents