Before Operation Checks - Honda GC135 Owner's Manual

2col_GC135_160_297x210_ORIZ_27lug09:297x210 (303x216) 25/09/09 13:04 Pagina 2
FEATURE
OIL ALERT SYSTEM (applicable types)
The Oil Alert system is designed to prevent engine damage
caused by an insufficient amount of oil in the crankcase. Before
the oil level in the crankcase can fall below a safe limit, the Oil
Alert system will automatically stop the engine.
If the engine stops and will not restart, check the engine oil level
(see page 4 ) before troubleshooting in other areas.
2

BEFORE OPERATION CHECKS

IS YOUR ENGINE READY TO GO?
For your safety, and to maximize the service life of your
equipment, it is very important to take a few moments before you
operate the engine to check its condition. Be sure to take care of
any problem you find, or have your servicing dealer correct it,
before you operate the engine.
Improperly maintaining this engine, or failure to
correct a problem before operation, can cause a
malfunction in which you can be seriously hurt or
killed.
Always perform a pre-operation inspection before
each operation, and correct any problem.
Before beginning your pre-operation checks, be sure the engine is
level and stopped.
Always check the following items before you start the engine:
Check the General Condition of the Engine
1. Look around and underneath the engine for signs of oil or
gasoline leaks.
2. Remove any excessive dirt or debris, especially around the
muffler and recoil starter.
3. Look for signs of damage.
4. Check that all shields and covers are in place, and all nuts, bolts,
and screws are tightened.
Check the Engine
1. Check the fuel level (see page 4 ). Starting with a full tank will
help to eliminate or reduce operating interruptions for refueling.
2. Check the engine oil level (see page 4 ). Running the engine
with a low oil level can cause engine damage.
The Oil Alert system (applicable types) will automatically stop
the engine before the oil level falls below safe limits. However,
to avoid the inconvenience of an unexpected shutdown, always
check the engine oil level before startup.
3. Check the air filter element (see page 5 ). A dirty air filter
element will restrict air flow to the carburetor, reducing engine
performance.
4. Check the equipment powered by this engine.
Review the instructions provided with the equipment powered
by this engine for any precautions and procedures that should
be followed before engine startup.
OPERATION
SAFE OPERATING PRECAUTIONS
Before operating the engine for the first time, please review the
SAFETY INFORMATION section on page and the BEFORE
1
OPERATION CHECKS on page .
2
Carbon monoxide gas is toxic. Breathing it can cause
unconsciousness and even kill you.
Avoid any areas or actions that expose you to carbon
monoxide.
Review the instructions provided with the equipment powered by
this engine for any safety precautions that should be observed
with engine startup, shutdown or operation.
Do not operate the engine on slopes greater than 20°.
STARTING THE ENGINE
1. Pull the choke rod to the CLOSED position.
C C L L O O S S E E D D
CHOKE ROD
Do not use the choke if the engine is warm or the air temperature
is high.
ENGLISH
2. Move the control lever.
Control lever with engine stop function:
Move the control lever away from the SLOW position, about 1/3
of the way toward the FAST position.
CONTROL LEVER
Control lever with only engine stop function:
Move the control lever to the ON position.
CONTROL LEVER
CLOSED
3. Pull the starter grip lightly until you feel resistance, then pull
briskly in the direction of the arrow as shown below. Return the
starter grip gently.
STARTER GRIP
D D i i r r e e c c t t i i o o n n
Do not allow the starter grip to snap back against the engine.
Return it gently to prevent damage to the starter.
F F A A S S T T
S S L L O O W W
S S T T O O P P
S S L L O O W W
S S T T O O P P
O O N N
O O N N
t t o o p p u u l l l l