Control Board Diagnostics - Bradford White RTG 199 MEN Installation And Operation Instructions Manual

7.6

Control board diagnostics

1. Press ON/OFF button into ON.
2. Immediately following, press and hold simultaneously buttons
or and for 3 seconds, until display reads P2.
P
3. Press to enter P2 adjustment. The current setting will appear on
P
the display. If not, repeat process.
4. Press and release the button on the control panel until the
P
display reads 'P4'. You are now in the diagnostic mode of the control
board.
5. When the display reads 'P4', press and release the
again and the display should read 'E'.
+
6. Use the and button on the control board to cycle through
different diagnostic modes available.
7. Once in the selected diagnostic mode of your choice, press and
release the button to display the diagnostic information.
P
EXAMPLE: to read the flow rate in gallons per minute while the unit is
flowing water, cycle to the '3d' mode and press the
reading of 25 on the display would indicate the heater is reading a flow
rate of 2.5 gallons/minute.
8. Once the information is obtained, press the
return to the diagnostic mode menu and scroll to addition diagnostic
information.
9. Press ON/OFF button to turn OFF the appliance and back ON again to
return heater to normal function.
Diagnostic menu
E Entry/Exit into sub-modes
0d Heat exchanger water temperature
1d Inlet water temperature (°F)
2d Outlet water temperature (°F)
3d Water flow (gallons/min)
4d Bypass control monitor (°F) [0d - 2d]
5d Fan speed (Hz)
6d Burner power (%)
7d Maximum power (kW)
8d Back flow temperature (°C)
9d Exhaust temperature (°C)
1F Most recent error/failure
2F 2nd most recent error
3F 3rd most recent error
4F 4th most recent error
5F 5th most recent error
6F 6th most recent error
7F 7th most recent error
8F 8th most recent error
9F 9th most recent error
10F 10th most recent error
1P* Appliance type - Cd (Condensing)
Appliance type - nC (Non condensing)
2P* Appliance power - 175 / 199 (kBTU/hr)
Table 38 * Settings define from factory
RTG 199 ME – 6 720 811 615 (2015/04)
Diagnostic menu
+
3P*
H0
H1
H2
+
button once
Table 38 * Settings define from factory
7.6.1
To see how many hours the appliance has worked, please enter the
"Diagnostic menu" (chapter 7.6);
▶ Select the sub-mode "H0".
▶ Select the sub-mode "H1".
button. A
P
▶ Select the sub-mode "H2".
button again to
P
After checking the sub-modes H0, H1 and H2, introduce the values in
the table below;
Working hours
Number in H0
Number in H1
Number in H2
(H0 + H1 + H2) = Total of hours
Table 39
Example:
Calculation of number of working hours,
Working hours
Number in H0
Number in H1
Number in H2
(H0 + H1 + H2) = Total of hours
Table 40
Temperature range - H (100-140°F)
Temperature range - C (100-184°F)
Numbers of hours - mode 0
Numbers of hours - mode 1
Numbers of hours - mode 2
Working hours
Write the number that shows in the display.
Write the number that shows in the display.
Write the number that shows in the display.
______ (X 100) =
______ (X 10 000) =
5 (X 100) =
0 (X 10 000) =
Maintenance and service
______ _______ +
_______ +
_______
__________
60 60 +
500 +
0
560
41