Bradford White RTG 199 MEN Installation And Operation Instructions Manual page 13

4.3.2 Vent specifications
Install appliance as close to point of vent termination as possible. The
exhaust piping must vent directly to the outside of the structure.
Horizontal sections of vent must pitch upward towards termination ¼"
for every foot of horizontal length, to prevent the pooling of condensate,
and be supported at 4 foot intervals with overhead hangers.
Exception: horizontal run between last elbow and termination must
pitch down to termination 1/4" per foot. Note: For horizontal
terminations, venting must terminate once it penetrates to the outside of
the structure. There must be no sections of vent pipe exposed to the
outdoors other than the termination. Note: Listed thimbles or collars are
necessary where venting passes through wall and ceiling partitions. If
the vent system passes through combustible areas where the vent
clearance requirements cannot be maintained, consult local codes. The
distance to combustibles using this chase technique is 1 inch. Note:
Type-B vent must never be used as the actual exhaust vent system for
the appliance, as it is not gas tight and illegal for use with this appliance.
This will create a serious health hazard and void the warranty.
3" VENTING Z flex
3" 2SVEEWCF0390
90° elbow
3" Tee 2SVSTTF03
Terminal
3" Horizontal 2SVSTB03
Terminal
3" horiz. 2SVSHTD03
terminal
with damper
3" Vertical 2SVSRCF03
Terminal
Table 6 3" Terminator Part Numbers
4" VENTING Z flex
4" 2SVEEWCF0490
90° elbow
4" Tee 2SVSTTF04
Terminal
4" Horizontal 2SVSTB04
Terminal
4" horiz. 2SVSHTD04
terminal
with damper
4" vertical 2SVSRCF04
terminal
Table 7 4" Terminator Part Numbers
For specific questions concerning vent material, specifications, usage or
installation, please contact the vent manufacturer directly.
RTG 199 ME – 6 720 811 615 (2015/04)
Protech Heat Fab
FSELB9003 9314
FSTT3 9390TEE
FSTB3 N/A
N/A N/A
FSRC3 5300CI
Protech Heat Fab
FSELB9004 9414
FSTT4 9490TEE
FSTB4 N/A
FSRC4 5400CI
N/A N/A
Company
Z-flex
ProTech Industries
Heat-Fab
Table 8 Vent manufacturers
Condensate drain requirements
An external condensate drain (not supplied with the heater) must be
installed under the following conditions:
• All vertical terminating vent installations.
• Horizontal terminating vent installations where the total linear vent
length is greater than 10 feet (3.1 m) for 3" and 5 feet (1.5 m) for 4".
• Vent installations where any section of the exhaust vent pipe passes
through an unconditioned space.
Twin pipe termination clearances
The minimum clearance between exhaust vent and combustion air inlet
terminations for twin pipe penetration is 3 feet.
Minimum combustion air and exhaust pipe length
The minimum exhaust pipe length is 1 foot (0.3m) of straight vent pipe.
The minimum combustion air pipe length is one 90° elbow.
Maximum combustion air and exhaust pipe length
The following tables display the maximum allowable straight pipe
lengths for combustion air and exhaust piping with consideration to the
number of elbows used. Reduce the equivalent length for each elbow
used from the maximum allowable length depending on the system
used.
Maximum Maximum
allowable allowable
Venting
total vent Exhaust
Length Length
3" 57 ft 28.5 ft
4" 122.5 ft 61.25 ft
Table 9 Maximum Allowable Exhaust and Combustion Air Lengths
Use of elbows
It is recommended to limit the amount of elbows used in the exhaust and
combustion air piping to reduce friction in the air flow. The following lists
the maximum amount of 90° elbows allowed in either the exhaust or
combustion air piping:
Max. number of 90° elbows
Max number of elbows
Table 10
Two 45° elbows are equal to one 90° elbow. Any
combination of 45° and 90° elbows may be used in
the vent system as long as the combination does not
exceed the maximum listed in table 9 above.
Installation instructions
Contact info
www.z-flex.com
800-654-5600
www.protechinfo.com
800-766-3473
www.heatfab.com
800-772-0739
Maximum Elbow
allowable Equivalency
Intake
Length
90° 45°
28.5 ft 5 ft 2.5 ft
61.25 ft 5 ft 2.5 ft
3" venting 4" venting
5 7
13