Denon DN-S3000 Operating Instructions Manual page 9

!9
(SAMP)EXIT/RELOOP
• Use this to turn the Sampler Loop mode on
and off. Also acts as EXIT/RELOOP button for
Sampler Loop to exit or back again.
@0
A/B TRIM button
With push of this button, the A and B
•
point trim mode changes on and off
while in PLAY or CUE mode.
@1
(SAMP.) STOP button
• Push this button while in Sampler record or
playback, Sampler record or playback stops.
@2
TITLE button
• CD TEXT:
When there is CD text data, the CD text data
is displayed when the button is pressed.
• MP3:
When an MP3 file has ID-3 tag data, the title,
artist name and album name are selected and
displayed each time the button is pressed.
@3
CONT./SINGLE, RELAY button
• CONT./SINGLE:
Short pushing play ending mode between
CONT (continue: play more tracks) and
SINGLE (stop playing and ReCUE's back to
your set point).
• SINGLE PLAY LOCK:
SINGLE PLAY LOCK can be selected by
PRESET(9). At this time , if this button is
pushed, it will be selected. When SINGLE
PLAY LOCK is selected, track selection during
playback is disabled. This prevents playback
from stopping when the Track Select Knob is
turned accidentally during playback.Play
ending mode is the same as single.
• RELAY:
You can turn on and off RELAY PLAY mode.
Relay playback is possible when two DN-
S3000s are connected by X-EFFECT.
@4
TIME, T.TIME button
• TIME:
A short push will displays mode changes
between ELAPSED TIME and REMAIN TIME.
• T.TIME:
A long push, will display mode changes
between TRACK TIME and DISC TIME.
• So, you can select display mode from four
modes, TRACK ELAPSED, TRACK REMAIN,
DISC ELAPSED and DISC REMAIN.
@5
MEMO, PRESET button
• MEMO:
The memo mode starts when this button is
pushed once in the Cue mode.
• PRESET:
When this button is pushed for more than 1
sec, the PRESET mode menu is displayed.
@6
(SAMP) PITCH button
• Push this button, pitch of Sampler can be
adjusted with the PARAMETERS knob.
@7
(SAMP) VOL. button
• Push this button, output level of Sampler
playback can be adjusted with
PARAMETERS knob.
@8
NEXT TRACK button
• If this button is pushed during playback, the
NEXT TRACK mode will be selected. The next
track can be selected with the PARAMETERS
knob.
@9
SCRATCH MODE, SEARCH button
Select the source for Scratch playback and the
manual search/bend mode.
• MAIN:
This button lights up or blinks at orange.
Manipulate Main Track sound
• SAMP.:
This button lights up or blinks at green.
Manipulate Sampler Track sound
• SEARCH:
When this button is pushed for more than 1
sec, the SEARCH mode is selected.
When the Scratch Disc selector is set to
SEARCH during playback, it works as the pitch
bend function.
When Scratch Disc is turned in the pause or
standby mode, works as the manual search
function. Manual search works and you can
move the CUE point around by one frame at a
time (1/75 second) with an audible frame-
repeat sound, da-da-da-da.
#0
TRACK/PARAMETERS knob
• TRACK:
When PARAMETERS LED is on, turn this knob
to select tracks.
By pushing this knob down while turning, the
tracks will change by 10 tracks at a time.
• PARAMETERS:
When the PARAMETER LED is flashing, turn
this knob to select and change the parameter
for items found in the Platter effects, Memo,
and Preset data, etc.
#1
FAST SEARCH (6),
1-MIN.SKIP button
#2
FAST SEARCH (7)
1-MIN.SKIP button
• 1-MIN.SKIP:
When one of these buttons is short pushed,
the playback position skips approximately 1
minute in the forward ( 6 ) or reverse (
direction.
• FAST SEARCH:
When one of these buttons is pressed and
held in, the disc is fast-searched in the forward
( 6 ) or reverse ( 7 ) direction.
the
#3
PITCH BEND – button
#4
PITCH BEND + button
• Pushing these buttons will change main
playing speed temporary.
• While pushing PITCH BEND + button playing
speed increases and speed decreases while
pushing PITCH BEND – button.
• When release button, playing speed returns to
the previous speed.
#5
Pitch Slider
• Use this slider to adjust playing speed.
• The playing speed decreases when slid
upwards and increases downwards.
#6
PITCH/KEY, RANGE button
• With this button you can select PITCH and
KEY ADJUST mode. Mode changes Pitch on,
Key Adjust on and both off cyclically. PITCH
LED indicates in Pitch mode and KEY ADJUST
indicator in the display lights up in Key Adjust
mode.
• RANGE:
Push this button for more than 1 sec to select
the pitch range. The pitch range can be
selected with the PARAMETERS knob.
#7
DUMP/RVS button
• Push this button to select between RVS or
DUMP and OFF.
#8
BRAKE button
• Push this button to set the BRAKE.
#9
DRAG-S button
• Push this button to set the DRAG-S.
7 )
ENGLISH
9