Page 1
For U.S.A., Canada, Europe & Japan model Ver. 1 SERVICE MANUAL DN-S3000 MODEL TABLE TOP SINGLE CD PLAYER For purposes of improvement, specifications and design are subject to change without notice. Please use this service manual with referring to the operating instructions without fail.
DN-S3000 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 3
DN-S3000 DISASSEMBLY (Follow the procedure below in reverse order when reassembling.) 1. SLIP DISK, SLIP MAT (1) Remove a screw and pull out Slip Disc and Slip Mat. Washer Slip Disc Slip Mat Slip Sheet Anti-static Sheet 2. PLATTER (1) Remove Belt from Motor Pully.
Page 4
DN-S3000 3. DRIVE UNIT (1) Remove 4 screws and pull out Drive Unit. (2) Disconnect Flat cable and Connector. (3) Detach Drive Unit. Drive Unit Connector Flat cable Drive Unit Note: Do not pull out aslant to prevent Flat cable damage.
Page 5
DN-S3000 5. SENSOR AND SCALE UNITS OF PLATTER (1) Remove 2 screws and pull out Sensor Cover and Sensor unit. (2) Remove a E Ring. (3) Pull out Scale unit. E Ring Sensor Cover Scale unit Sensor unit 6. SENSOR AND SCALE UNITS OF SLIP DISC (1) Remove 2 screws and pull out Sensor Cover and Sensor unit.
Page 6
DN-S3000 8. DSP PWB UNIT (1) Remove 9 screws and pull out DSP PWB unit. DSP PWB unit 9. DRIVE COVER (1) Remove 4 screws and pull out Drive cover. Drive cover 10. DRIVE (1) Move Drive Rack in arrow direction through the Hole on the bottom chassis.
DN-S3000 BLOCK DIAGRAM DN-S3000 -HB,F1,F2 GND,+5 D16~31 128M LRCK TFS0 analog out SDRAM TCK0 BCLK ADSP21065L TXD0A ADRESS MAIN PANEL µcom DRIVE 32bit BUS TXD0B digital out Trans AK4353 ATAPI INTERFACE SHOCK PROOF MAIN DOUT CLOCK TXD1B TMP86CM47U ROM32k LED out...
Page 8
DN-S3000 CONFIRMING THE SERVO Required Measuring Implement Reference disc (TCD784 or CO-74176) 1. What is Service Program Service program is a special program intended for confirming servo functions etc. 2. Contents of Service Program Switch on the power while pushing the PITCH BEND + button and SCRATCH MODE button at the same time. After actuating the servo program, select an aiming process number with the SELECT knob, A button, B button, SAMP button, or SAMP B button.
Page 9
DN-S3000 Adjustment Value indication at Adjustment Item character portions. Focus Gain 35 ~ 120 Focus Balance -20 ~ +20 -20 ~ +20 Focus Offset Tracking Gain 35 ~ 120 -20 ~ +20 Tracking Balance Tracking Offset -20 ~ +20 * Reference data.
Page 10
DN-S3000 Detailed error can be displayed by PLATTER when error occurs. Error Indication FRAM CHARACTER Displays the track Displays the time at which error occurred. “H * * * * E * * * ” No. in which error occurred.
Page 11
DN-S3000 Only major semiconductors are shown, general semiconductors etc. are omitted to list. 1. IC’s Note : Abbreviation ahead of IC No. indicates the name of P.W.B., etc. DS : DSP P.W.B. PA : PANEL P.W.B. CD : CD-ROM P.W.B.
Page 12
DN-S3000 Symbol Symbol Port Name Function (IC301) (IC401) — — — — — SDCLK1 — — SDRAM clock enable 1 — — — — — — — — — — Power (+3.3V) SDCLK0 — — — — SDRAM clock enable 0 DMAR1_ —...
Page 13
DN-S3000 Symbol Symbol Port Name Function (IC301) (IC401) — — — — — Power (+3.3V) DATA9 — — — — Ext. bus data 9 DATA10 — — — — Ext. bus data 10 DATA11 — — — — Ext. bus data 11 —...
Page 14
DN-S3000 Symbol Symbol Port Name Function (IC301) (IC401) RESET_ DRES_ DRES_ — — DSP reset signal — — — — — Power (+3.3V) — — — — — ADDR23 — — — — Ext. bus address 23 ADDR22 — —...
Page 16
DN-S3000 Pin No. Type Description Pin Name XSSBAD Sub-beam addition signal input Phase detector reference current generator. Connect a resistor between this pin and XSPDIREF ground to set reference current Frequency detector reference current generator. Connect a resistor between this pin and...
Page 17
DN-S3000 Pin No. Pin Name Type Description XHPDIAGJ This pin is used as the Passed Diagnostics signal, and may be an input or an open-drain output This pin is used as the Drive Active/Slave Present signal, and is an input or an open-drain XHDASPJ output.
Page 18
DN-S3000 MN102H730F (DS: IC501) TOP VIEW MN102H730F Terminal Function Pin Name Symbol Function CS0_ CS0_ — — — Ext. memory chip select 0 (Flash ROM CS) CS1_ CS1_ — — — Ext. memory chip select 1 (Flash ROM for memo) —...
Page 19
DN-S3000 Pin Name Symbol Function MUTE — Mute signal (H: Mute) — — — — Oscillation input — — — — Oscillation output — — — — — Power (+3.3V) OSCI OSCI — — — — Oscillation input, 32.0MHz OSCO OSCO —...
Page 20
DN-S3000 Pin Name Symbol Function MCNT0 — Motor control signal 0 MCNT1 — Motor control signal 1 P96,DAC2 MCNTDA — Motor rotation speed control signal A/D 0 P97,DAC3 RESERVE — — — BREQ_ BREQ_ — (Pu) Bus request signal BRACK_ BRACK_ —...
Page 24
DN-S3000 SP-3721A (CD: IC502) DVDRFP SDEN DVDRFN SDATA SCLK TOP VIEW MEVO MLPF SP3721A Terminal Function Pin No. Type Description Pin Name 1, 2 DVDREP , DVDREN RF Signal Inputs. Differential RF signal attenuator input pins CDRF RF Signal Inputs. Single-ended RF signal attenuator input pin...
Page 25
DN-S3000 Pin No. Pin Name Type Description Center Error Signal Output. Center error output reference to VCI NEVO SIGO Bottom Envelope Output. Bottom envelope for mirror detection Defect Output. Pseudo CMOS output. When a defect is detected, the DFT output goes high. Also the servo AGC output can be monitored at this pin, when CAR bits 7-4 are ‘0011’...
DN-S3000 TMP86CM47U-4V14 (PA: IC102) TOP VIEW TMP86CM47U-4V14 Terminal Function Pin No. Pin Name Symbol Function GND (0V) Oscillation input 16.0MHz XOUT XOUT Oscillation output TEST TEST Fixed to L Power (+5.0V) PITCHLED LED ON/OFF (L:ON) EJECTLED LED ON/OFF (L:ON) RESET_...
Page 27
DN-S3000 TMP86CM47U-3RD2 (DS: IC151) TOP VIEW TMP86CM47U-3RD2 Terminal Function Pin Name Symbol Function — — — — — GND (0V) — — — — Oscillation input 8.0MHz XOUT XOUT — — — — Oscillation output TEST TEST — — —...
Page 28
DN-S3000 W29EE011P (CD: IC507) Terminal Function Name Function OUTPUT A0 - A16 Address Inputs CONTROL BUFFER DQ0 - DQ7 Data Inputs/Outputs Chip Enable VIEW Output Enable Write Enable CORE DECODER Power Supply ARRAY Ground 14 15 16 17 18 19 20...
Page 29
DN-S3000 BA5954FP (CD: IC509) PreGND PGND PVcc2 7.5k STAND LOADING ACTUATOR DRIVER DRIVER THERMAL 7.5k SHUT DOWN DET.AMP . PVcc1 PVcc2 DET.AMP . SLED ACTUATOR 7.5k DRIVER DRIVER 7.5k PVcc1 PGND BA5954FP Terminal Function Function Function Name Name VINFC Focus driver input VOTK+ Output (+) of tracking driver 2 CFCerr1 Cap.
Page 30
DN-S3000 AK4353VF Terminal Function Pin Name Description MCKO Master Clock Output Pin Same frequency as MCKI is output Transmit Channel Output Pin DVDD Digital Power Supply Pin, +2.7∼+5.5V DVSS Digital Ground Pin, 0V MCKI Master Clock Input Pin BICK Serial Data Clock Pin...
Page 31
DN-S3000 TA7291F (DS: IC512) TA7291F Terminal Function PIN No. SYMBOL FUNCTION DESCRIPTION Supply voltage terminal for Logic OUT1 OUT2 Supply voltage terminal for Motor driver Supply voltage terminal for control GND terminal Input terminal Vref Input terminal OUT1 Output terminal...
Page 32
DN-S3000 2. FL DISPLAY 24-ST-09GN (FL101) Pin Connection Pin No. Connection Pin No. Connection — — — — NOTE: 1) F- , F+ Filament 2) NP No Pin 3) DL Datum Line 4) 1G~24G Grid 5) IC Internal Connection 6) Visual Field Upper 26 , lower 26 (min.)
Page 33
DN-S3000 PRINTED WIRING BOARDS GU-3414 CD-ROM P.W.B. UNIT COMPONENT SIDE FOIL SIDE...
Page 34
DN-S3000 GU-3546 DSP P.W.B. UNIT COMPONENT SIDE...
DN-S3000 NOTE FOR PARTS LIST Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis- supplying.
Page 39
DN-S3000 PARTS LIST OF P.W.B. UNIT Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model GU-3414A CD-ROM P.W.B. UNIT ASS'Y Ref.No. Part No. Part Name Remarks Q'ty...
Page 47
DN-S3000 Ref.No. Part No. Part Name Remarks Q'ty OTHER PARTS GROUP CW031 203 5280 039 3P KR-DS CONN.CORD CW041 203 6393 048 4P KR-DS CON CORD CW042 203 6393 022 4P KR-DS CON CORD CW091 204 2464 013 9P KR-DS CONN.CORD...
Page 48
DN-S3000 EXPLODED VIEW Parts List WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
Page 49
DN-S3000 PARTS LIST OF EXPLODED VIEW Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model Ref.No. Part No. Part Name Remarks Q'ty GU-3546 DSP PWB UNIT GU-3547...
Page 51
DN-S3000 EXPLODED VIEW OF CD DRIVE UNIT (FG-5000) Parts List Adjust the HEAT SINK to this line when placing it Bond this part (SC-608LZ) Fix this part with two-sided adhesive tape (58-3) (58-2) (58-1) Bond these part (SC-608LZ) (58-3) (58-2)
Page 52
DN-S3000 PARTS LIST OF CD DRIVE UNIT (FG-5000) Ref.No. Part No. Part Name Remarks Q'ty 9KA 2A49 6A CD MECHA ASS'Y TD-S202H2D GU-3414A CD-ROM PWB UNIT 415 0900 001 PROTECT SHEET 412 4997 008 DRIVE BRACKET HEAT SINK 9KC 2G03 9A...
Page 54
DN-S3000 PARTS LIST OF CD MECHANISM UNIT ( TD-S202SA(D) ) Ref. No. Part No. Part Name Remarks Q'ty New Ref. No. Part No. Part Name Remarks Q'ty New 20 9KC 8G00 6 GEAR-LOAD-A 9KC 8A00 1 CLAMPER-PLATE ASSY 21 9KC 8G00 7...
Page 55
DN-S3000 Ref. No. Part No. Part Name Remarks Q'ty New Ref. No. Part No. Part Name Remarks Q'ty New T/T MOTOR ASSY 74-1 TABLE-M32 74-2 MAGNET-M32 SCREWS 74-3 RUBBER-M32 74-4 BACK YOKE-M32 35 9KS 14N1 02 M1.4X2 PRECISION SCREW TYPE-1 74-5 T.T BUSH-SLOT-NI...
Page 56
DN-S3000 PACKING VIEW Contents PARTS LIST OF PACKING & ACCESSORIES Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model Ref.No. Part No. Part Name Remarks Q'ty 505 0350 019...
Page 57
DN-S3000 WIRING DIAGRAM DN-S3000 SINGLE CD PLAYER WIRING DIAGRAM CX031(FG5000) OUTSW 1 OUTSW SLOT IN DET SLOT IN DET 3 GND CX042(FG5000) LED POEWR1 LED POEWR1 INSW 2 INSW 3 GND LED POEWR2 LED POEWR2 CX021(FG5000) LOAD- 1 LOAD- GU-3547-5 DISC SENSOR UNIT...
Page 58
DN-S3000 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufactur- CAUTION: Before returning the unit to the customer, make sure you make µ either (1) a leakage current check or (2) a line to chassis resis- tance check.
Page 59
DN-S3000 SCHEMATIC DIAGRAMS (1/5) SIGNAL LINE SCHEMATIC DIAGRAMS (1/5) GU-3414 CD-ROM UNIT...
Page 60
DN-S3000 SCHEMATIC DIAGRAMS (2/5) SCHEMATIC DIAGRAMS (2/5) SIGNAL LINE GU-3546 DSP UNIT (1/2)
Page 61
DN-S3000 SCHEMATIC DIAGRAMS (3/5) SIGNAL LINE SCHEMATIC DIAGRAMS (3/5) GU-3546 DSP UNIT (2/2)
Page 62
DN-S3000 SCHEMATIC DIAGRAMS (4/5) SCHEMATIC DIAGRAMS (4/5) GU-3547-1 PANEL UNIT GU-3547-2 PANEL2 UNIT GU-3547-3 FLT UNIT GU-3547-4 SLIDE VR UNIT GU-3547-5 DISC SENSOR UNIT GU-3547-6 TABLE SENSOR UNIT...