Using The Video Setup - Denon DVD-2910 Operating Instructions Manual

ENGLISH
When the Display Position is Selected and
Adjusted:
• Press the cursor button (ª), then select the
horizontal/vertical direction with the cursor
buttons ( , ), set the adjustment value with
0 1
the (• , ª ) cursor buttons, and press the
ENTER button.
SETUP LEVEL (0 IRE, 7.5 IRE)
(Factory default: 0 IRE)
6
• This corrects floating black.
H. POSITION (–7 to +7) (Factory default: 0)
• A 15-step portion of position adjustment is
permitted left and right.
V. POSITION (–3 to +7) (Factory default: 0)
• A 11-step portion of position adjustment is
permitted up and down.
The picture and sound may be disturbed while
the display position is being adjusted.
To exit the picture adjust mode
Press the PICTURE ADJUST button.
PICTURE MODE STD(STANDARD)
M1(MEMORY1)
1(ADJUSTMENT 1)
M2(MEMORY2)
M3(MEMORY3)
2(ADJUSTMENT 2)
M4(MEMORY4)
M5(MEMORY5)
GAMMA
SET(PIC SETUP)
26
P I CT URE MODE
STD M1 M2 M3 M4 M5 SET
Remote control unit
P I C S ET UP
Remote control unit
SE TUP LEVE L
0 0
0
CONTRAST
BRIGHTNESS
1 Only effective for progressive scan.
SHARPNESS(MID)
2 Only effective for HDMI, DVI and
1
SHARPNESS(HI)
progressive scan.
HUE
2
CCS •
When HDMI and DVI signals are
output, the SHARPNESS (MID/HI),
WHITE LEVEL
CHROMA DELAY and Gamma
CHROMA LEVEL
1
CHROMA DELAY
correction settings will have no
DNR
effect.
G0~G9
SETUP LEVEL
H.POSITION 2
V.POSITION
2
12

USING THE VIDEO SETUP

The video output setting of the HDMI and the DVI-D connectors can be changed.
2
The video output setting of the PICTURE MODE, PROGRESSIVE MODE and ADJUST MODE also can be
2
changed.
PLAY
OPEN/CLOSE
DBY
Display the setting mode
The HDMI, DVI, 480P, 576P, 720P and 1080i
indicators flash when the connection is being
checked, then stop flashing, remaining lit, once
the check is completed.
Press the HDMI/DVI SELECT button.
• The modes described below will appear on the
display.
HDMI/DVI OFF (FACTORY DEFAULT)
No output signals from the HDMI and DVI-D
connectors.
This mode is set to use the COMPONENT VIDEO
OUT connector.
HDMI Y Cb Cr
Outputs the component signals from the HDMI
1
connector.
HDMI RGB
Outputs the RGB signals from the HDMI
connector.
DVI
Outputs the RGB signals from the DVI-D
connector.
The video signals are only output from one of
the HDMI, DVI or progressive component
video output connectors.
Press the HDMI/DVI FORMAT button.
• The modes described below will appear on the
display.
Select the item you wish to set and press the
select knob to define it.
480P/576P (FACTORY DEFAULT)
Outputs the image from the HDMI or DVI-D
connector at 480P or 576P.
720P
Outputs the image from the HDMI or DVI-D
connector at 720P.
1080i
Outputs the image from the HDMI or DVI-D
2
connector at 1080i.
• When playing back a PAL-formated disc, be sure
to set the TV TYPE option to NTSC. (See pages 18,
19.)
• The video or audio signals may be interrupted
when the output setting mode is switched.
• Depending on the TV you are using, if the TV's
input is not set to HDMI or DVI, the HDMI or DVI
OFF mode may be set. In this case, set the TV's
input setting to HDMI or DVI before performing
the DVI setup procedure.
• Connect to an HDCP compatible display to view
images with DVI connections.
1 2
STOP
STILL / PAUSE
SUPER PURE
AUDIO CD DIRECT HDMI / DVI
SELECT SELECT FORMAT
SETUP
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-2910
1 2
HDMI / DVI HDMI/DVI OFF
SELECT FORMAT
HDMI Y Cb Cr
Main unit
HDMI/DVI
SELECT FORMAT
HDMI R G B
Remote
DVI
control unit
480P/576P
720P
1080i
HDMI / DVI
HDMI/DVI
SELECT FORMAT
SELECT FORMAT
Main unit Remote control unit