User Program; Functions That Can Be Set With User Programs; Toner Save Mode (Al-2020/2035/2040); User Programs (Al-2020/2035/2040) - Sharp AL-2020 Service Manual

[11] USER PROGRAM

The conditions of factory setting can be changed according to the
use conditions.
1. Functions that can be set with user
programs
Toner save mode
Reduces toner consumption by approximately 10%.
Power save modes
The unit has two power save modes of operation: preheat mode
and auto power shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save (
cator will light up and other indicators will remain on or off as
before. In this condition, the fuser in the unit is maintained at a
lower heat level, thereby saving power. To copy from the preheat
mode, make desired copier selections and press the start (
key using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power
save ( ) indicator will light up and other indicators except the
ONLINE indicator will go out. The auto power shut-off mode saves
more power than the preheat mode but requires a longer time
before starting copying. To copy from the auto power shut-off
mode, press the start ( ) key. Then make desired copier selec-
tions and press the start ( ) key using the normal copying proce-
dure.
Auto clear
The unit returns to the initial settings a preset amount of time after
the end of job.
This preset amount of time (auto clear time) can be changed.
Resolution of AUTO & MANUAL mode
You can set the copy resolution used for AUTO and MANUAL
( ) exposure mode.

2. Toner save mode (AL-2020/2035/2040)

1) Press the exposure mode selector key to select the MANUAL
( ) mode.
2) Press and hold down the exposure mode selector key for
approximately 5 seconds. The MANUAL (
go out and the PHOTO (
light and dark indicator marked "5" will light up, indicating the
standard toner mode is active.
) indi-
) indicator will
) indicator will begin to blink. The
AL-2020/2035/2040/2050/2060 USER PROGRAM 11 - 1
3) To enter the toner save mode, press the light (
light and dark indicator marked "1" will light up, indicating the
toner save mode is selected.
4) Press the exposure mode selector key. The PHOTO (
indicator will stop blinking and light up steadily. The light and
dark indicator marked "3" will light up. The toner save mode is
now active.
Note: To return to the standard mode, repeat the procedure but
use the dark (
3).

3. User programs (AL-2020/2035/2040)

)
The user programs allow the parameters of certain functions to be
set, changed, or canceled as desired.
Set the power save modes, auto clear time, preheat mode,
SPF automatic original discharge time, resolution of AUTO &
MANUAL mode and reset factory setting.
1) Press and hold down the light (
more than 5 seconds until all the alarm indicators (
) blink and "
2) Use the left copy quantity (
number (1: Auto clear time, 2: Preheat mode, 3: Auto power
shut off mode, 4: Auto power shut off timer, 6: SPF automatic
original discharge time, 10: Resolution of AUTO & MANUAL
mode, 21: Reset factory, 24: Prevention of OC copies when
the SPF is up function, 25: Copy effective paper width setting
function (Bypass tray), 26: Copy effective paper width setting
function (Tray), 28: Selection of copy start state (Polygon rota-
tion on/off), 29: Fusing temperature setting when the bypass
tray is used). The selected number will blink in the left side of
the display.
3) Press the start (
steadily lit and the currently selected parameter number for the
program will blink on the right side of the display.
4) Select the desired parameter using the right copy quantity
( ) key. The entered parameter number will blink on the
right of the display.
Program
Mode
No.
1 Auto clear time
2 Preheat mode
Auto power shut off mode *1 → ON, 2 → OFF
3
4 Auto power shut off timer
6 SPF automatic original
discharge time
10 Resolution of AUTO &
MANUAL mode
21 Reset factory
24 Prevention of OC copies
when the SPF is up
function
) key to select exposure level "5" in step
) key simultaneously for
" appears in the display.
) key to select a user program
) key. The entered program number will be
Parameters
1 → 10 sec., 2 → 30 sec.,
*3 → 60 sec., 4 → 90 sec.,
5 → 120 sec., 6 → OFF
*1 → 30 sec., 2 → 60 sec.,
3 → 5 min., 4 → 30 min.,
5 → 60 min., 6 → 120 min.,
7 → 240 min.
*1 → 5 min., 2 → 30min.,
3 → 60 min., 4 → 120 min.,
5 → 240 min.
1 → 5 min., *2 → 30 min.,
3 → 60 min., 4 → 120 min.,
5 → 240 min., 6 → OFF
*1 → 300dpi, 2 → 600dpi
1 → YES, *2 → NO
*1 → ON, 2 → OFF
) key. The
)
, ,