Table of Contents
Advertisement
[12] USER PROGRAM
The user settings consist of the following items.
1. User programs
A. Copy mode
Program
Program name
number
1
AUTO CLEAR
2
PREHEAT MODE
3
AUTO SHUT-OFF
4
AUTO SHUT-OFF
TIME
5
STREAM FEEDING
6
LAYOUT IN 2IN1
7
OFFSET
FUNCTION
8
ROTATE ORIG.
IMAGE
9
AE/TEXT
RESOLUTION
10
2-SIDED COPY
MODE (AR-168L
only)
11
MARGIN WIDTH
12
MEM. FOR
PRINTER
13
AUTO KEY REPEAT 1: ON
14
KEY PRESS TIME
Setting codes
(factory default setting
appears in bold)
1: 10 SEC.
• Auto clear time automatically returns the copy settings to the initial settings if no
2: 30 SEC.
keys are pressed for a preset period of time following the end of a copy job.
3: 60 SEC.
• This program is used to select the period of time. Auto clear time can also be
4: 90 SEC.
disabled.
5: 120 SEC.
6: OFF
1: 30 SEC.
• This function automatically switches the machine to a low power consumption
2: 1 MIN.
state if the set duration of time elapses without the machine being used when the
3: 5 MIN.
power is on. The power save indicator lights up, however, the keys on the
4: 30 MIN.
operation panel can be used. Normal operation automatically resumes when a key
5: 60 MIN.
on the operation panel is pressed, an original is placed, a print job is received.
6: 120 MIN.
7: 240 MIN.
1: ON
• Use this setting to enable or disable auto power shut-off mode.
2: OFF
1: 5 MIN.
• This function automatically switches the machine to a state that consumes even
2: 30 MIN.
less power than preheat mode if the set duration of time elapses without the
3: 60 MIN.
machine being used when the power is on. All lights except the power save
4: 120 MIN.
indicator go off. To resume normal operation, press the [START] key. Normal
5: 240 MIN.
operation also resumes automatically when a print job is received or scanning is
begun from a computer. While in auto power shut-off mode, no keys (except the
[START] key) can be used.
1: ON
• When copying using the RSPF, while "SET ORIGINALS FOR STREAM
2: OFF
FEEDING." appears in the display after an original has been scanned (about 5
seconds), a subsequent original can be placed and automatically fed into the
machine.
1: PATTERN 1
• Use this setting to select the layout pattern when two original pages are copied
2: PATTERN 2
onto a single sheet of paper.
1: ON
• When enabled, this function offsets the position in the paper output tray of sets of
2: OFF
copies during copy job, and print jobs when using the printer function.
1: ON
• When two-sided copying is performed, this function rotates the image on the back
2: OFF
of the original. This is convenient when binding the copies at the top (tablet
binding).
1: 300dpi
• This setting is used to change the copy resolution in AUTO and TEXT mode from
2: 600dpi
600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slower when high-
quality mode is used.
1: HI-SPEED
• If the memory fills up when two-sided copying is performed, "NORMAL" can be
2: NORMAL
selected to make copying possible. However, "NORMAL" results in a slower
copying speed. Normally "HI-SPEED" is selected to enable fast two-sided
copying.
1: 1/4"
• Use this setting to set the margin width.
2: 1/2"
3: 3/4"
4: 1"
1: 30%
• Use this to change the proportion of machine memory used for printer mode.
2: 40%
3: 50%
4: 60%
5: 70%
• Use this setting to select whether or not holding down a key causes repeated input
2: OFF
of the key. For keys that normally cause a set value to increase when held down
(for example, holding down the [<] key [v] or [>] key [^]), this program can be used
to have the set value not change when the key is held down.
1: NORMAL
• Use this setting to select how long a key must be pressed for the input to be
2: 0.5 SEC.
accepted. By selecting a longer time, you can prevent settings from being
3: 1.0 SEC.
changed by the accidental pressing of a key.
4: 1.5 SEC.
5: 2.0 SEC.
AR-168N/168L USER PROGRAM 12 - 1
Explanation
Advertisement
Table of Contents
