Important Notes - Kohler command pro ECH749 Service Manual

When key switch is turned ON and all safety switch
requirements are met, ECU activates fuel pump module
for about six seconds, which pressurizes system for
start-up. If key switch is not promptly turned to start
position, engine fails to start, or engine is stopped with
key switch ON (as in case of an accident), ECU switches
off pump preventing continued delivery of fuel. In this
situation, MIL will go on, but it will go back off after 4
cranking revolutions if system function is OK. Once
engine is running, fuel pump remains on.
Precision components inside fuel pump module are not
serviceable. DO NOT attempt to open fuel pump module.
Damage to components will result and warranty will be
void. Because fuel pump module is not serviceable,
engines are equipped with a special 10-micron EFI fuel
fi lter to prevent harmful contamination from entering
module.
If there are two fi lters in system, one before lift pump
will be a standard 51-75 micron fi lter, and one after lift
pump will be special 10-micron fi lter. Be sure to use an
approved 10-micron fi lter for replacement.
High pressure fuel line is an assembly of hoses, injector
caps and a fuel connector to fuel pump module. High
pressure fuel line feeds fuel to top of injectors through
injector caps. Caps are fastened to intake manifold and
injectors are locked into place. A small retaining clip
provides a secondary lock.
High pressure fuel line is serviced as a complete
assembly to prevent tampering and safety hazards.
Components are not individually serviceable.
Vent hose assembly is intended to vent fuel vapor out of
fuel pump module and direct fuel vapor into throttle body.
Most EFI engines are equipped with an engine mounted
purge port on #2 cylinder barrel baffl e. This capped
purge port can be used by OEM to vent fuel tanks or
used in conjunction with a carbon canister kit for Tier III
evaporative emissions compliance. Purge port connects
to vent hose assembly and directs all fuel vapor into
throttle body. If purge port remains unused, port must
remain capped to prevent dirt from entering engine.
EFI engines have no carburetor, so throttle function
(regulate incoming combustion airfl ow) is achieved with
a throttle valve in a separate throttle body attached to
intake manifold. Throttle body/intake manifold provides
mounting for fuel injectors, throttle position sensor, either
a separate MAP sensor and an intake air temperature
(IAT) sensor, or a TMAP sensor, high pressure fuel line,
idle speed screw, and air cleaner assembly.
Idle speed is only adjustment that may be performed on
EFI system. Standard idle speed setting for EFI engines
is 1500 RPM, but certain applications might require
a different setting. Check equipment manufacturer's
recommendation.
24 690 01 Rev. K
For starting and warm up, ECU will adjust fuel and
ignition timing, based upon ambient temperature, engine
temperature, and loads present. In cold conditions,
idle speed will probably be different than normal for a
few moments. Under other conditions, idle speed may
actually start lower than normal, but gradually increase
to established setting as operation continues. Do not
attempt to circumvent this warm up period, or readjust
idle speed during this time. Engine must be completely
warmed up, in closed loop operating mode for accurate
idle adjustment.

IMPORTANT NOTES!

● Cleanliness is essential and must be maintained at all
times when servicing or working on EFI system. Dirt,
even in small quantities, can cause signifi cant
problems.
● Clean any joint or fi tting with parts cleaning solvent
before opening to prevent dirt from entering system.
● Always depressurize fuel system through fuel
connector on fuel pump module before disconnecting
or servicing any fuel system components.
● Never attempt to service any fuel system component
while engine is running or ignition switch is ON.
● Do not use compressed air if system is open. Cover
any parts removed and wrap any open joints with
plastic if they will remain open for any length of time.
New parts should be removed from their protective
packaging just prior to installation.
● Avoid direct water or spray contact with system
components.
● Do not disconnect or reconnect ECU wiring harness
connector or any individual components with ignition
on. This can send a damaging voltage spike through
ECU.
● Do not allow battery cables to touch opposing
terminals. When connecting battery cables attach
positive (+) cable to positive (+) battery terminal fi rst,
followed by negative (-) cable to negative (-) battery
terminal.
● Never start engine when cables are loose or poorly
connected to battery terminals.
● Never disconnect battery while engine is running.
● Never use a quick battery charger to start engine.
● Do not charge battery with key switch ON.
● Always disconnect negative (-) battery cable before
charging battery, and also unplug harness from ECU
before performing any welding on equipment.
KohlerEngines.com
EFI SYSTEM-ECH
33