Oven Light - Jenn-Air JGS8750 User Manual

IJ INTENANC, co T.
LEVELING LEGS ELECTRICAL OVEN BOTTOM
• Besure the anti-tip bracket secures one
CONNECTION
ofthe rear leveling legs to thefloor.This I_---_ Theovenbottom on a conventional bake
bracketpreventstherangefromacciden- Appliances which__ rangemayberemovedfor easier cleaning.
tallytipping, require electrical NOTE: The oven bottom on convec-
power areequipped tion models is not removable.
The rangeshouldbe lev- with a three-prong
TO REMOVE:Whencool,re-_
eledwheninstalled.If the grounding plug movethe ovenracks.Slide t_
range isnot level,turnthe whichmustbeplugged d irectlyintoaprop- two catches, Io-
plasticlevelinglegs,Io- erlygrounded three-hole120volt electri- cotedat eachrear
cotedateachcar- coloutlet, cornerof the oven
her of the
range, until Always disconnect power to appliance b efore bottom,towardthe t3.,.
range islevel, servicing, front of the oven.
Thethree-pronggroundingplugofferspro- Lift the rear edgeof the oven bottom
tection against s hockhazards. DO NOT slightly,then slideit backuntil the front
OVEN
LIGHT
CUT OR REMOVE THE THIRD edgeof the ovenbottom clearsthe oven
GROUNDING PRONG FROM THE front frame.Removeoven bottom from
Toassurethe proper replacementbulb POWER CORD PLUG. oven,
is used,order bulb from Maytag Cus-
tomer Service. Call 1-800-688-8408, If anungrounded, two-holeor other type TO REPLACE:Fitthe front edge of the
askforpartnumber74OO4458-halogen electrical o utlet is encountered, it is the oven bottom into the ovenfront frame.
bulb. personal responsibility of the appli- Lower the rear of the oven bottom and
slidethetwo catches b ackto locktheoven
ante owner to have the outlet re-
CAUTION:
placed with a properly grounded bottom inplace.
three.hole electrical outlet.
• Disconnectpower to rangebefore
replacinglightbulb.
TO REMOVE RANGE
• Allow oven to cool before replacing
STORAGE DRAWER FOR CLEANING
AND
lightbulb. The storage drawer at the bottom of the
SERVICING
• Makesurebulbcoverandbulbarecool range is safe and convenient for storing
before touching, metalandglasscookware. DO NOT store I. Shut off gas supplyto appliance.
plastic,paperware,food or flammablema- 2. Disconnect electrical supply to appli-
TO REPLACE OVEN LIGHT BULB: terial in this drawer. Remove drawer to ance, ifequipped.
cleanunder range.
I. When oven is cool, use fingertips to 3. Disconnect gas supply tubing to appli-
graspedgeof bulbcover.Pullout and TO REMOVE: Emptydrawer thenpull once.
remove, out to thefirststopposition. L iftupfrontof
drawer andpull to the second stop posi- 4. Sliderangeforwardto disengage from
2. Carefullyremoveold bulb by pulling tion. Graspsidesand lift up andout to anti-tipbracket.(Seelnstallationlnstruc-
straight out of ceramic base. removedrawer, tionsfor locationof bracket.)
3. Toavoiddamagingordecreasingthelife TOREPLACE:Fittheendsofthedrawer 5. Reverse procedureto reinstall.If gas
of the newbulb,do not touchthe bulb glidesonto the rails.Lift up drawerfront line hasbeendisconnected, checkfor
with barehands or fingers. H oldwith a andgentlypush into firststopposition. L ift gas leaks afterreconnection. NOTE: A
cloth or paper towel. Pushnew bulb up and continueto slidedrawer to the qualifiedservicershoulddisconnect
prongsstraight into smallholes of closedposition, andreconnectgassupply.
ceramic base. 6, To prevent a ccidental tipping, r ange must
4. Replacebulb cover by snapping into be secured to the floor by sliding rear
place, leveling leginto anti-tipbracket.
5. Reconnect power to the range.Reset
clock.
17