Installer's Programming - Codes And Options; User Functions - DSC PC1832 Reference Manual

If the Master Code Not Changeable option is enabled the Sys-
tem Master Code can only be changed using Installer Program-
ming.
EN
NOTE:
For EN installations the installer will not have access
to Master Code Programming. In order to return the master code
to the factory default setting enter the Special Installer Function
[989][Installer's Code][989] (Master Code Factory Default Program-
ming). This will allow the installer to default the Master Code.
Duress Codes - Access Codes [33] and [34]
Duress codes are standard user codes that will transmit the
Duress Reporting Code whenever the code is entered to perform
any function on the system.
NOTE: Duress codes are not valid when entering [*][5], [*][6] or
[*][8] sections.
NOTE: Duress codes cannot be programmed as a duplicate of
another code or as a "Code + 1".
Maintenance Code
The maintenance code can only be used to arm and disarm the
system. It cannot be used to bypass zones, to access the
Escort5580(TC), or to cancel or postpone automatic arming. The
code can only be programmed in Installer's Programming. The
Maintenance code cannot bypass zones, use [*][9] to arm the
system, cancel auto-arming, or perform [*][7] command functions.
There will be no arm/disarm bell squawks when the Maintenance
code is used.
C
Guard Code
The Guard Code can arm the panel at any time. However, the
Guard code can only disarm the system after an alarm, tamper,
fault or trouble condition has occurred. It can also be used to
bypass zones and activate Command Outputs. The Guard Code
may be programmed in Section [008].
Arming and disarming using the Guard Code will log as "Closing
(Opening) by Maintenance Code". If a Command Output that
requires a code is activated with the Guard Code, no User Log will
be made. When zones are bypassed with the Guard Code, the
panel will log "[*][1] Access by User".
NOTE:
The Latching Trouble feature should be used with the
Guard Code feature in order disarm with Trouble Present.
Partition Assignments and Access Code Attributes
You can enable or disable each access code to work on each par-
tition. Additional access code attributes are also programmable.
Attributes determine what abilities the code will have.
By default, each code has the attributes of the code used to pro-
gram it. For example, if you use the Master code to program other
access codes, the new codes will have the same attributes as the
Master code. You can change the partition and attribute program-
ming by following the instructions described below.
You cannot change Master code partition or attribute program-
ming. The Master code has all partitions and all attributes turned
on, except for the Bell Squawk on Arming/Disarming and One
Time Use Code Attributes.
Access Code Partition Assignment
To program which partition(s) each code will work on:
1. Enter [*][5][Master Code][8] for partition programming.
2. Enter the 2-digit number of the access code you want to edit.
3. Enter the partition number (1-8) to toggle it on or off.
NOTE:
Partition programming is NOT supported by the following
keypads: PC5508(Z), PC5516(Z), PC5532(Z) versions v2.00 and
lower; LCD5500(Z) version 2.x and lower; LCD5501Z version 1.x
and lower.
Access Code Attributes
To program each attribute:
1. Enter [*][5][Master Code][9] for attribute programming.
2. Enter the 2-digit number of the access code you want to edit.
3. Enter the attribute number to toggle it on or off.
Programmable Attributes
Attribute Description
[1] For Future Use
[2] For Future Use
[3] Zone Bypass enabled.
This attribute allows the user to bypass zones.
[4] Escort5580(TC) Remote Access
This attribute allows the user to access the security system
via the Escort, if installed.
[5] For Future Use
[6] For Future Use
[7] Bell Squawk on Arming/Disarming. When this attribute is ON,
the bell will squawk when the access code is entered to arm
or disarm the system. For example, you can use the arm/dis-
arm bell squawk attribute to have wireless key access codes
squawk the bell, while other codes are silent. To do this,
enable attribute [7] on all access codes associated with wire-
less keys.
[8] One Time Use Code. This attribute will only affect Access
Codes 01-16. If the panel is disarmed with this code, the
code will be erased at the end of the Exit Delay the next time
that the panel is armed, regardless of which code is used to
arm the system. The code will also be erased at the end of
the Exit Delay when used to arm the panel. If the panel is dis-
armed during the Exit Delay when armed with a One Time
Use Code, it will still be valid after the next time the panel is
armed (unless the same One Time Code is used to arm the
second time).
NOTE: If you enable the Bell Squawk on Arming/Disarming
option (section [014], option [1]), the bell will sound arm/disarm
bell squawks for all access codes, regardless of the programming
for attribute [7] (see Section 5.3 Basic Programming PWS Section 3
[001]-[004] (see Section 5.4 'Advanced Programming').

Installer's Programming - Codes and Options

There are three codes which can be programmed by the installer
in Installer's Programming: the Installer's code, Master Code
and a Maintenance Code/Guard Code. All other access codes
can be programmed through the [*][5] command, as described
previously in this section.
The master code can also be programmed by the user as access
code (40). However, if the Master Code Not Changeable option
is enabled, the master code can only be accessed in Installer's
Programming.
General access codes can arm and disarm the system. When the
Code Required for Bypassing option is enabled, users must
enter a valid access code in order to bypass zones. Individual
access codes can have the Zone Bypassing attribute disabled
under Access Code Attribute programming, as described previ-
ously in this section.
If the 6-Digit User Access Codes option is enabled, all the
access codes are programmed with six digits instead of four. The
Installer's Code will become [555555]. If 4-digit codes are already
programmed and this option is selected, the first four digits of the
programmed codes will remain as programmed and the last two
digits will be [00].
If the 4-Digit User Access Codes is selected, all codes will be 4-
Digits in length, with the exception of the Panel ID code and the
Downloading Access Code. If 6-digit codes were previously pro-
grammed and this option is enabled, the first four digits of each
code will be used.
Installer's Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [006]
Maintenance Code. . . . . . . . . . . . . . . . . . . . . . . . . . .Section [008]
Master Code Not Changeable . . . . . . . . . . . . . . .Section [015]: [6]
Code Required for Bypassing . . . . . . . . . . . . . . . .Section [015]: [5]
6-digit User Access Codes . . . . . . . . . . . . . . . . . .Section [701]: [5]
NOTE: Only one keypad at a time can use [*][5] programming.

[*][6] User Functions

NOTE: Only one keypad at a time can use [*][6] programming.
15